Answer:
(a). The largest value of θ is 71.9°.
(b). The second largest value of θ is 57.7°.
(c). The third largest value of θ is 47.7° .
Explanation:
Given that,
Width of diffraction grating [tex]w= 19.2\ mm[/tex]
Number of rulings[tex]N=6010[/tex]
Wavelength = 337 nm
We need to calculate the distance between adjacent rulings
Using formula of distance
[tex]d=\dfrac{w}{N}[/tex]
Put the value into the formula
[tex]d=\dfrac{19.2\times10^{-3}}{6010}[/tex]
[tex]d=3.19\times10^{-6}\ m[/tex]
We need to calculate the value of m
Using formula of constructive interference
[tex]d \sin\theta=m\lambda[/tex]
[tex]\sin\theta=\dfrac{m\lambda}{d}[/tex]
Here, m = 0,1,2,3,4......
[tex]\lambda[/tex]=wavelength
For largest value of θ
[tex]\dfrac{m\lambda}{d}>1[/tex]
[tex]m>\dfrac{d}{\lambda}[/tex]
Put the value into the formula
[tex]m>\dfrac{3.19\times10^{-6}}{337\times10^{-9}}[/tex]
[tex]m>9.46[/tex]
[tex]m = 9[/tex]
(a). We need to calculate the largest value of θ
Using formula of constructive interference
[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]
Now, put the value of m in to the formula
[tex]\theta=\sin^{-1}(\dfrac{9\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]
[tex]\theta=71.9^{\circ}[/tex]
(b). We need to calculate the second largest value of θ
Using formula of constructive interference
[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]
Now, put the value of m in to the formula
[tex]\theta=\sin^{-1}(\dfrac{8\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]
[tex]\theta=57.7^{\circ}[/tex]
(c). We need to calculate the third largest value of θ
Using formula of constructive interference
[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]
Now, put the value of m in to the formula
[tex]\theta=\sin^{-1}(\dfrac{7\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]
[tex]\theta=47.7^{\circ}[/tex]
Hence, (a). The largest value of θ is 71.9°.
(b). The second largest value of θ is 57.7°.
(c). The third largest value of θ is 47.7° .
local unit of measurement of length : confined to a particular place cise Choose the best answer from the given alterna MKS system stands for ........ i. mass, kilogram and second ii. metre, kilogram and second iii. metre, kilometre and second iv. metre, kilogram and standard
MKS stands for metre , kilogram and second
If a disk rolls on a rough surface without slipping, the acceleration of the center of gravity (G) will _ and the friction force will b
Answer:
Will be equal to alpha x r; less than UsN
g As observed on earth, a certain type of bacteria is known to double in number every 24 hours. Two cultures of these bacteria are prepared, each consisting initially of one bacterium. One culture is left on earth and the other placed on a rocket that travels at a speed of 0.893c relative to the earth. At a time when the earthbound culture has grown to 256 bacteria, how many bacteria are in the culture on the rocket, according to an earth-based observer
Answer:
86.4 hrs
Explanation:
The amount of bacteria is initially 1
It doubles every 24 hrs.
After first 24 hrs, the amount = 2
After next 24 hrs = 4
After next 24 hrs = 8
After next 24 hrs = 16
After next 24 hrs = 32
After next 24 hrs = 64
After next 24 hrs = 128
After next 24 hrs = 256
Total time taken to reach 256 = 24 x 8 = 192 hrs
For the bacteria culture on the rocket that travels at a speed of 0.893c relative to the earth, this time is contracted by the relationship
t = t'(1 - ¥^2)^0.5
Where t is the contracted time =?
t' is the time on earth
¥ = v/c
Where v is the speed of the rocket
c is the speed of light
since v = 0.893c
¥ = 0.893
Substituting, we have
t = 192 x (1 - 0.893^2)^0.5
t = 192 x 0.2025^0.5
t = 192 x 0.45 = 86.4 hrs
Charge of uniform density (0.30 nC/m2) is distributed over the xy plane, and charge of uniform density (−0.40 nC/m2) is distributed over the yz plane. What is the magnitude of the resulting electric field at any point not in either of the two charged planes?
Answer: E = 39.54 N/C
Explanation: Electric field can be determined using surface charge density:
[tex]E = \frac{\sigma}{2\epsilon_{0}}[/tex]
where:
σ is surface charge density
[tex]\epsilon_{0}[/tex] is permitivitty of free space ([tex]\epsilon_{0} = 8.85.10^{-12}[/tex][tex]C^{2}/N.m^{2}[/tex])
Calculating resulting electric field:
[tex]E=E_{1} - E_{2}[/tex]
[tex]E = \frac{\sigma_{1}-\sigma_{2}}{2\epsilon_{0}}[/tex]
[tex]E = \frac{[0.3-(-0.4)].10^{-9}}{2.8.85.10^{-12}}[/tex]
[tex]E=0.03954.10^{3}[/tex]
E = 39.54
The resulting Electric Field at any point is 39.54N/C.
The magnitude of the resulting electric field at any point should be 28.2 N/C.
Calculation of the magnitude:Since the Charge of uniform density (0.30 nC/m2) should be allocated over the xy plane, and charge of uniform density (−0.40 nC/m2)should be allocated over the yz plane.
So,
E1
= σ1/2ε0
= 0.30e-9/(2*8.85e-12)
= 16.949 N/C
So, direction of E1 is +z
Now
E2 = σ2/2ε0
= 0.40e-9/(2*8.85e-12)
= 22.6 N/C
So, direction of E2 is -x
Now
E = √(E1*E1+E2*E2)
= √(16.949*16.949+22.6*22.6)
= 28.2 N/C
Learn more about magnitude here: https://brainly.com/question/14576767
Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 2.2% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of the galaxy relative to the earth
Answer:
Vrel= 0.75c
Explanation:
See attached file
The elastic portion of the downward-sloping straight-line demand curve lies:_______
a. at the intersection with the supply curve.
b. anywhere to the right of the current market price.
c. above the point of unit elasticity.
d. below the point where total revenue is maximized.
Answer:
c. above the point of unit elasticity.
Explanation:
The elastic portion of the downward-sloping straight-line demand curve lies above the point of unit elasticity. Supply and demand are fundamental concept in economics. The demand curve shows how much of a good people will want at a different prices. The demands curves illustrates the intuition why people purchase a good for a lower price. For the demand curve, the price is always shown on the vertical axis and the demand curve is shown on the horizontal axis. Thus , the quantity demanded increases as the price gets lower. However, the price elasticity of the demand curve varies along the demand curve. This is because there is a key distinction between the gradient and the elasticity. The gradient which is the slope of the line is always the same in the demand curve but elasticity of the demand changes in the percentage of the quantity demand. Therefore, elasticity will vary along the downward-sloping straight - line demand curve. So, in a downward-sloping straight-line demand curve, the elastic portion is usually above the point of unit elasticity
The highest mountain on mars is olympus mons, rising 22000 meters above the martian surface. If we were to throw an object horizontaly off the mountain top, how long would it take to reach the surface? (Ignore atmospheric drag forces and use gMars=3.72m/s^2
a. 2.4 minutes
b. 0.79 minutes
c. 1.8 minutes
d. 3.0 minutes
Answer:
t = 1.81 min , the correct answer is c
Explanation:
This is a missile throwing exercise
The object is thrown horizontally, so its vertical speed is zero (voy = 0), let's use the equation
y = y₀ + [tex]v_{oy}[/tex] t - ½ g t²
the final height is y = 0 and the initial height is y₀ = 22000 m
0 = y₀ + 0 - ½ g t²
t = √y 2y₀ / g
let's calculate
t = √(2 22000 / 3.72)
t = 108.76 s
let's reduce to minutes
t = 108.76 s (1 min / 60 s)
t = 1.81 min
The correct answer is c
Select the situation for which the torque is the smallest.
a. A 200 kg piece of silver is placed at the end of a 2.5 m tree branch.
b. A 20 kg piece of marble is placed at the end of a 25 m construction crane arm.
c. A 8 kg quartz rock is placed at the end of a 62.5 m thin titanium rod.
d. The torque is the same for two cases.
e. The torque is the same for all cases.
Answer:
e. The torque is the same for all cases.
Explanation:
The formula for torque is:
τ = Fr
where,
τ = Torque
F = Force = Weight (in this case) = mg
r = perpendicular distance between force an axis of rotation
Therefore,
τ = mgr
a)
Here,
m = 200 kg
r = 2.5 m
Therefore,
τ = (200 kg)(9.8 m/s²)(2.5 m)
τ = 4900 N.m
b)
Here,
m = 20 kg
r = 25 m
Therefore,
τ = (20 kg)(9.8 m/s²)(25 m)
τ = 4900 N.m
c)
Here,
m = 8 kg
r = 62.5 m
Therefore,
τ = (8 kg)(9.8 m/s²)(62.5 m)
τ = 4900 N.m
Hence, the correct answer will be:
e. The torque is the same for all cases.
A thick wire with a radius of 4.0 mm carries a uniform electric current of 1.0 A, distributed uniformly over its cross-section. At what distance from the axis of the wire, and greater than the radius of the wire, is the magnetic field strength equal to that at a distance 2.0 mm from the axis. distance
Answer:
8 mm
Explanation:
From the information given:
The Ampere circuital law can be used to estimate the magnetic field strength at two points when the distance is less than the radius and when the distance is greater than the radius.
when the distance is less than the radius ; we have:
[tex]B_1 = \dfrac{ \mu_o \times I \times r}{2 \times \pi \times \ d^2}[/tex]
when the distance is greater than the radius; we have:
[tex]B_2 = \dfrac{\mu_o \ \times I}{2 \ \times \pi \times R}[/tex]
Equating both equations together ; we have :
[tex]\dfrac{ \mu_o \times I \times r}{2 \times \pi \times \ d^2} = \dfrac{\mu_o \ \times I}{2 \ \times \pi \times R}[/tex]
[tex]\dfrac{1}{R}= \dfrac{r}{d^2}[/tex]
[tex]R= \dfrac{d^2}{r}[/tex]
where; d = radius of the wire and r = distance;
[tex]R =\dfrac{4^2}{2}[/tex]
[tex]R =\dfrac{16}{2}[/tex]
R = 8 mm
A thermos bottle works well because:
a. its glass walls are thin
b. silvering reduces convection
c. vacuum reduces heat radiation
d. silver coating is a poor heat conductor
e. none of the above
Answer:
A thermos bottle works well because:
A) Its glass walls are thin
Answer:
A thermos bottle works well because:
C
Vacuum reduces heat radiation
6. What is the bulk modulus of oxygen if 32.0 g of oxygen occupies 22.4 L and the speed of sound in the oxygen is 317 m/s?
Answer:
[tex] \boxed{\sf Bulk \ modulus \ of \ oxygen \approx 143.5 \ kPa} [/tex]
Given:
Mass of oxygen (m) = 32.0 g = 0.032 kg
Volume occupied by oxygen (V) = 22.4 L = 0.0224 m³
Speed of sound in oxygen (v) = 317 m/s
To Find:
Bulk modulus of oxygen
Explanation:
[tex]\sf Density \ of \ oxygen \ (\rho) = \frac{m}{V}[/tex]
[tex]\sf \implies Bulk \ modulus \ of \ oxygen \ (B) = v^{2} \rho[/tex]
[tex]\sf \implies B = v^{2} \times\frac{m}{V}[/tex]
[tex]\sf \implies B = {(317)}^{2} \times \frac{0.032}{0.0224} [/tex]
[tex]\sf \implies B = {(317)}^{2} \times 1.428[/tex]
[tex]\sf \implies B = 100489 \times 1.428[/tex]
[tex]\sf \implies B = 143498.292 \: Pa[/tex]
[tex]\sf \implies B \approx 143.5 \: kPa[/tex]
A 50.0 ohm and a 30.0 ohm resistor are connected in parallel. What is their equivalent resistance? Unit=Ohms
R(parallel) = product/ sum
50×30/50+30
1500/80
18,75 ohms
Answer: 18.75
above is right but you need to put a dot after the number 18
If a bus travels 50 km in 10 hours, how fast was the
bus travelling?
Answer:
5 kilometers per hour
Explanation:
Speed = distance / time
Distance: 50km
Time: 10 hours
Speed = 50/10 = 5kph
Answer:
5kmph
Explanation:
if the bus traveled 50 km in 10 hours, we have to divide 50 by 10 to see how fast it traveled per hour.
50/10 = 5
therefore, the bus was traveling 5 km per hour
hope this helps :)
What type of energy conversion occurs when you place your feet near the fireplace and they become warm?
O Radiant to thermal
o Thermal to mechanical
O Mechanical to chemical
O Nuclear to thermal
Answer:
It is the first one RADIENT TO THERMAL
Explanation:
The heat emitted from the campfires is an an example of radiant energy and thermal energy is refers to the energy contained within a system that is responsible for its tempreture with in this case is the campfires and heat energy being reflected upon your feet.
Answer:
A
Explanation:
The speed of a horse is 134 meters per second how long does it takes to travel a distance of 19,311?
Answer:
just need some focus
Explanation:
tan 13. The speed of a horse is 134 meters per second how long does it take to travel a distance of 19,311m? M+ tud V 134 14. You are walking down the block and see your neighbor's pitbull 30 meters away, out of the fence, starring at you. Suddenly, he starts running towards you at 20m/s. How long will it be before you're the pitbull's lunch? V 15. A pendulum has a frequency of 2 Hz what is it's period. T = 1/2 16. You have just finished a 1600 mile trip, and it took you 16 hours. What was your average speed V = Ad At 17. You are flying from New York, NY to SanFrancisco California, a distance of 2582 miles, it takes 6.33hrs to complete the flight what was your average speed? give answer in m/s. V = Ad = At 3 of 6
A load of 1 kW takes a current of 5 A from a 230 V supply. Calculate the power factor.
Answer:
Power factor = 0.87 (Approx)
Explanation:
Given:
Load = 1 Kw = 1000 watt
Current (I) = 5 A
Supply (V) = 230 V
Find:
Power factor.
Computation:
Power factor = watts / (V)(I)
Power factor = 1,000 / (230)(5)
Power factor = 1,000 / (1,150)
Power factor = 0.8695
Power factor = 0.87 (Approx)
calculate horizontal distance travelled by a ball travelling with a speed of 20root2 mper sec without hitting ceiling of height 20 m per sec
Calculate the horizontal distance travelled by a ball throw with a velcoity 20 sqrt 2 ms^(-1) without hitting the ceiling of an anditorium of heith 20 m. Use g= 10 ms^(-2). =(20√2)2sin2×45∘10=9800×1)10=80m .
HOPE SO IT HELPS YOU
When a battery is connected to a lightbulb properly, current flows through the lightbulb and makes it glow. How much current flows through the battery compared with the lightbulb
Answer:
The same amount of current flows through the battery and light bulb
Explanation:
Because for a single loop, the current is the same at every point in the loop. Thus, the amount of current that flows through the lightbulb is the same as the amount that flows through the battery
Answer:
The same amount of current flows through the battery and light bulb
Explanation:
The advantage of a hydraulic lever is A : it transforms a small force acting over a large distance into a large force acting over a small distance. B : it transforms a small force acting over a small distance into a large force acting over a large distance. C : it allows you to exert a larger force with less work. D : it transforms a large force acting over a large distance into a small force acting over a small distance. E : it transforms a large force acting over a small distance into a small force acting over a large distance.
Answer:
A) it transforms a small force acting over a large distance into a large force acting over a small distance.
Explanation:
The hydraulic lever works based on Pascal's law of transmission of pressure through a fluid. In the hydraulic lever, the pressure transmitted is the same.
Pressure transmitted P = F/A
where F is the force applied
and A is the area over which the force is applied.
This pressure can be manipulated on the input end as a small force applied over a small area, and then be transmitted to the output end as a large force over a large area.
F/A = f/a
where the left side of the equation is for the output, and the right side is for the input.
The volume of the displaced fluid will be the same on both ends of the hydraulic lever. Since we know that
volume V = (area A) x (distance d)
this means that the the piston on the input smaller area of the hydraulic lever will travel a greater distance, while the piston on the larger output area of the lever will travel a small distance.
From all these, we can see that the advantage of a hydraulic lever is that it transforms a small force acting over a large distance into a large force acting over a small distance.
If the terminals of a battery with zero internal resistance are connected across two identical resistors in series, the total power delivered by the battery is 8.00 W. If the same battery is connected across the same resistors in parallel, what is the total power delivered by the battery
Answer:
24W
Explanation:
The series connection has a resistance of 2R
The parallel connection has a resistance of R/2 .. the resistance has decreased by a factor 4
Assuming the battery still provides the same pd .. the current increases by a factor of 4 .. increasing the power output by a factor of 4 also (P = V x A)
Power output = 4 x 8W .. .. So P = 24 W
Three capacitors C1 = 10.7 µF, C2 = 23.0 µF, and C3 = 29.3 µF are connected in series. To avoid breakdown of the capacitors, the maximum potential difference to which any of them can be individually charged is 125 V. Determine the maximum energy stored in the series combination.
Answer:
E = 1336.71875 J
Explanation:
We are given;. Capacitance of Capacitor 1; C1 = 10.7 µF
Capacitor 2; C2 = 23.0 µF
Capacitor 3; C3 = 29.3 µF
Supply voltage;V = 125 V
Formula for capacitance in series is;
Capacitors in series circuit: C(eq) = 1/C(1) +1/C(2) +1/C(3) .......
Thus, equivalent capacitance is;
C(eq) = (1/10.7) + (1/23) + (1/29.3) = 0.1711 µF = 0.1711 × 10^(6) F
Now, the formula for maximum energy stored is;
E = ½ × C(eq) × V²
E = ½ × 0.1711 × 10^(-6) × 125²
E = 1336.71875 J
A child is trying to throw a ball over a fence. She gives the ball an initial speed of 8.0 m/s at an angle of 40° above the horizontal. The ball leaves her hand 1.0 m above the ground and the fence is 2.0 m high. The ball just clears the fence while still traveling upwards and experiences no significant air resistance. How far is the child from the fence?
Answer:
the child is 1.581 m far from the fence
Explanation:
The diagrammatic illustration that give a better view of what the question denote can be seen in the image attached below.
From the image attached below, let assume that the release point is the origin, then equation of the motion (x) is as follows:
[tex]x - x_o = u_xt[/tex]
[tex]\mathtt{x = u_xt \ \ \ since (x_o = 0)}[/tex] ---- (1)
the equation of the motion y is :
[tex]\mathtt{y - y_o =u_yt - 0.5 gt^2}[/tex]
[tex]\mathtt{y = u_yt-4.9t^2 \ \ \ since (y_o =0)}[/tex]
[tex]\mathtt{ 1= (u \ sin 40^0)t -4.9 \ t^2 }[/tex]
[tex]\mathtt{1 = 8 sin 40^0 t - 4.9 t^2}[/tex]
[tex]\mathtt{1 = 5.14t - 4.9t^2}[/tex]
[tex]\mathtt{4.9t^2 - 5.14t +1 = 0}[/tex]
By using the quadratic formula, we have;
[tex]\mathtt{ \dfrac{ -b \pm \sqrt{b^2 - 4ac}}{2a}} }[/tex]
where;
a = 4.9, b = -5.14 c = 1
[tex]= \mathtt{ \dfrac{ -(-5.14) \pm \sqrt{(-5.14)^2 - 4(4.9)(1)}}{2(4.9)}} }[/tex]
[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{26.4196 -19.6}}{9.8}} }[/tex]
[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{6.8196}}{9.8}} }[/tex]
[tex]= \mathtt{ \dfrac{ 5.14+ \sqrt{6.8196}}{9.8} \ \ OR \ \ \dfrac{ 5.14- \sqrt{6.8196}}{9.8}} }[/tex]
[tex]= \mathtt{ \dfrac{ 5.14+ 2.6114}{9.8} \ \ OR \ \ \dfrac{ 5.14- 2.6114}{9.8}} }[/tex]
[tex]= \mathtt{ \dfrac{ 7.7514}{9.8} \ \ OR \ \ \dfrac{ 2.5286}{9.8}} }[/tex]
[tex]= \mathbf{ 0.791 \ \ OR \ \ 0.258} }[/tex]
In as much as the ball is traveling upward, then we consider t= 0.258sec.
From equation (1)
[tex]\mathtt{x = u_x(0.258)}[/tex]
[tex]\mathtt{x = ucos 40^0 (0.258)}[/tex]
[tex]\mathtt{x = 8 \ cos 40^0 (0.258)}[/tex]
[tex]\mathbf{x = 1.581 \ m}[/tex]
Thus, the child is 1.581 m far from the fence
A projectile is shot from the edge of a cliff 80 m above ground level with an initial speed of 60 m/sec at an angle of 30° with the horizontal. Determine the time taken by the projectile to hit the ground below.
Answer:
8 seconds
Explanation:
Answer:
Explanation:
Going up
Time taken to reach maximum height= usin∅/g
=3 secs
Maximum height= H+[(usin∅)²/2g]
=80+[(60sin30)²/20]
=125 meters
Coming Down
Maximum height= ½gt²
125= ½(10)(t²)
t=5 secs
A patient prescribed a metered dose inhaler will find it
A. works for lower (not upper) respiratory diseases only.
B. should be filled with medication in aerosol form only.
C. is filled with medication used to administer a fixed amount of medication per inhalation through the mouth.
D. should be filled with medication in powder form only.
Answer:The correct answer should be C. is filled with medication used to administer a fixed amount of medication per inhalation through the mouth.
Explanation:
Answer:
c. is filled with medication used to administer a fixed amount of medication per inhalation through the mouth.
A charged capacitor and an inductor are connected in series. At time t = 0, the current is zero, but the capacitor is charged. If T is the period of the resulting oscillations, the next time, after t = 0 that the energy stored in the magnetic field of the inductor is a maximum is
Answer:
t = T / 2 all energy is stored in the inductor
Explanation:
The circuit described is an oscillating circuit where the charge of the condensation stops the inductor and vice versa, in this system the angular velocity of the oscillation is
w = √1/LC
2π / T =√1 / LC
T = 2π √LC
The energy is constant and for the initial instant it is completely stored in the capacitor
Uc = Q₀² / 2C
In the process, the capacitor is discharging and the energy is stored in the inductor until when the charge in the capacitors zero, all the energy is stored in the inductor
U = L I² / 2
in the intermediate instant the energy is stored in the two elements.
Since the period of the system is T for time t = 0 all energy is stored in the capacitor and for t = T / 2 all energy is stored in the inductor
After t = 0 the maximum energy stored in the magnetic field of the inductor is equal to [tex]U'=\dfrac{L I^{2}}{2}[/tex] for the time period, half of period of oscillation (t = T/2).
The given problem is based on the charging and discharging concepts of capacitor. An oscillating circuit is a circuit where the charge of the capacitor stops the inductor and vice versa, in this system the angular frequency of the oscillation is given as,
[tex]\omega =\dfrac{1}{\sqrt{LC}}\\\\\\\dfrac{2 \pi}{T} =\dfrac{1}{\sqrt{LC}}\\\\\\T = 2\pi \times \sqrt{LC}[/tex]
here, T is the period of oscillation.
Also, the energy stored in the capacitor is constant and for the initial instant it is completely stored in the capacitor. So, the energy stored is given as,
[tex]U =\dfrac{Q^{2}}{2C}[/tex]
here, C is the capacitance.
In the process, the capacitor is discharging and the energy is stored in the inductor until when the charge in the capacitors zero, all the energy is stored in the inductor. So, the expression for the energy stored in the inductor is,
[tex]U'=\dfrac{L I^{2}}{2}[/tex]
here, L is the inductance and I is the current.
Note :- The period of the system is T for time t = 0 all energy is stored in the capacitor and for t = T / 2 all energy is stored in the inductor.
Thus, we conclude that after t = 0 the maximum energy stored in the magnetic field of the inductor is equal to [tex]U'=\dfrac{L I^{2}}{2}[/tex] for the time period, half of period of oscillation (t = T/2).
Learn more about the capacitance here:
https://brainly.com/question/12644355
Activity
Spend time observing or thinking about events that involve matter and energy. Which events can you explain? Which
events can't you explain? Now answer the following questions.
Part A
Describe three events that you cannot explain.
Answer:Eating. Your muscles in your arms and mouth use energy to feed itself. Then your body digest the food which also takes energy.
Sleep. When your tired, you don’t have much energy. It is said that you use more energy while your sleeping. But how do you become energized if you were using even more energy than before?
Answer:
Different kinds of balls bounce to different heights when dropped on the same floor.
Sugar dissolves faster in hot milk than in cold milk.
Plants grow more slowly when they are not near a window.
Explanation:
What is the angle between a wire carrying an 8.40 A current and the 1.20 T field it is in, if 50.0 cm of the wire experiences a magnetic force of 2.55 N? ° (b) What is the force (in N) on the wire if it is rotated to make an angle of 90° with the field? N
Answer:
A. 30.38°
B 5.04N
Explanation:
Using
F= ILBsin theta
2 .55N= 8.4Ax 0.5mx 1.2T x sintheta
Theta = 30.38°
B. If theta is 90°
Then
F= 8.4Ax 0.5mx 1.2x sin 90°
F= 5.04N
In order to waken a sleeping child, the volume on an alarm clock is doubled. Under this new scenario, how much more energy will be striking the child's ear drums each second?
Answer:4 times more energy will be striking the childbearing
Explanation:
Because Volume is directly proportional to amplitude of sound. Energy is proportional to amplitude squared. If you triple the amplitude, you multiply the energy by 4
3. Which of the following accurately describes circuits?
O A. In a parallel circuit, the same amount of current flows through each part of the circuit
O B. In a series circuit, the amount of current passing through each part of the circuit may vary
O C. In a series circuit, the current can flow through only one path from start to finish
O D. In a parallel circuit, there's only one path for the current to travel.
Answer:
Option (c)
Explanation:
In a Series circuit, as the components are connected end-to-end ,the current can flow through only one path from start to finish.
(C.) is the only correct statement in the list of choices.
In a series circuit, the current can flow through only one path from start to finish.
"A light beam incident on a diffraction grating consists of waves with two different wavelengths. The separation of the two first order lines is great if"
Answer:
A light beam incident on a diffraction grating consists of waves with two different wavelengths. The separation of the two first order lines is great if
the dispersion is great