Answer:
the magnitude of the electric field is 1.25 N/C
Explanation:
The induced emf in the cube ε = LB.v where B = magnitude of electric field = 5 T , L = length of side of cube = 1 cm = 0.01 m and v = velocity of cube = 1 m/s
ε = LB.v = 0.01 m × 5 T × 1 m/s = 0.05 V
Also, induced emf in the cube ε = ∫E.ds around the loop of the cube where E = electric field in metal cube
ε = ∫E.ds
ε = Eds since E is always parallel to the side of the cube
= E∫ds ∫ds = 4L since we have 4 sides
= E(4L)
= 4EL
So,4EL = 0.05 V
E = 0.05 V/4L
= 0.05 V/(4 × 0.01 m)
= 0.05 V/0.04 m
= 1.25 V/m
= 1.25 N/C
So, the magnitude of the electric field is 1.25 N/C
The magnitude of the electric field is 1.25 N/C
Calculation of the magnitude of the electric field:But before that the following calculations need to be done.
ε = LB.v = 0.01 m × 5 T × 1 m/s
= 0.05 V
Now
ε = ∫E.ds
here ε = Eds because E is always parallel to the side of the cube
So,
= E∫ds ∫ds
= 4L so we have 4 sides
Now
= E(4L)
= 4EL
So,4EL = 0.05 V
Now
E = 0.05 V/4L
= 0.05 V/(4 × 0.01 m)
= 0.05 V/0.04 m
= 1.25 V/m
= 1.25 N/C
hence, The magnitude of the electric field is 1.25 N/C
learn more about electric field here: https://brainly.com/question/1834208
In the lab, you shoot an electron towards the south. As it moves through a magnetic field, you observe the electron curving upward toward the roof of the lab. You deduce that the magnetic field must be pointing:_______.
a. to the west.
b. upward.
c. to the north.
d. to the east.
e. downward.
Answer:
a. to the west.
Explanation:
An electron in a magnetic field always experience a force that tends to change its direction of motion through the magnetic field. According to Lorentz left hand rule (which is the opposite of Lorentz right hand rule for a positive charge), the left hand is used to represent the motion of an electron in a magnetic field. Hold out the left hand with the fingers held out parallel to the palm, and the thumb held at right angle to the other fingers. If the thumb represents the motion of the electron though the field, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the particle.
In this case, if we point the thumb (which shows the direction we shot the electron) to the south (towards your body), with the palm (shows the direction of the force) facing up to the roof, then the fingers (the direction of the field) will point west.
A radar installation operates at 9000 MHz with an antenna (dish) that is 15 meters across. Determine the maximum distance (in kilometers) for which this system can distinguish two aircraft 100 meters apart.
Answer:
R = 36.885 km
Explanation:
In order to distinguish the two planes we must use the Rayleigh criterion that establishes two distinguishable objects if in their diffraction the central maximum of one coincides with the first minimum of the other
The diffraction equation for slits is
a sin θ = m λ
the first minimum occurs for m = 1
sin θ = λ a
as the diffraction experiments the angles are very small, we approximate
sin θ = θ
θ = λ / a
This expression is for a slit, in the case of circular objects, when solving the system in polar coordinates, a numerical constant appears, leaving the expression of the form
θ = 1.22 λ / a
In this problem they give us the frequency, let's find the wavelength with the relation
c = λ f
λ = c / f
θ = 1.22 c/ f a
since they ask us for the distance between the planes, we can use the definition of radians
θ = s / R
if we assume that the distance is large, we can approximate the arc to the horizontal distance
s = x
we substitute
x / R = 1.22 c / fa
R = x f a / 1.22c
Let's reduce the magnitudes to the SI system
f = 9000 MHz = 9 109 Hz
a = 15 m
x = 100 m
let's calculate
R = 100 10⁹ 15 / (1.22 3 108)
R = 3.6885 10⁴ m
let's reduce to km
R = 3.6885 10¹ km
R = 36.885 km
A square coil of wire with 15 turns and an area of 0.40 m2 is placed parallel to a magnetic field of 0.75 T. The coil is flipped so its plane is perpendicular to the magnetic field in 0.050 s. What is the magnitude of the average induced emf
Answer:
The magnitude of the average induced emf is 90V
Explanation:
Given;
area of the square coil, A = 0.4 m²
number of turns, N = 15 turns
magnitude of the magnetic field, B = 0.75 T
time of change of magnetic field, t = 0.05 s
The magnitude of the average induced emf is given by;
E = -NAB/t
E = -(15 x 0.4 x 0.75) / 0.05
E = -90 V
|E| = 90 V
Therefore, the magnitude of the average induced emf is 90V
What is the emf of this cell under standard conditions? Express your answer using three significant figures.
Complete Question
A voltaic cell utilizes the following reaction and operates at 298 K:
3Ce4+(aq)+Cr(s)→3Ce3+(aq)+Cr3+(aq).
What is the emf of this cell under standard conditions? Express your answer using three significant figures.
Answer:
The value is [tex]E^o_{cell} = 2.35 V[/tex]
Explanation:
From the question we are told that
The ionic equation is
[tex]3 Ce^{4 +} _{(aq)} + Cr _{(s)} \to 3 Ce^{3+} _{(aq)} + Cr^{3r} _{(aq)}[/tex]
Now under standard conditions the reduction half reaction is
[tex]Ce^{4+} + e \to Ce^{3+} ; \ \ E^o_r = 1.61 V[/tex]
And the oxidation half reaction is
[tex]Cr^{3+} + 3e^{-} \to Cr ; \ \ \ E^o_o = - 0.74 V[/tex]
The emf of this cell under standard conditions is mathematically represented as
[tex]E^o_{cell} = E^o _r - E^o _o[/tex]
substituting values
[tex]E^o_{cell} = 1.61 - (- 0.74)[/tex]
[tex]E^o_{cell} = 2.35 V[/tex]
Ellen says that whenever the acceleration is directly proportional to the displacement of an object from its equilibrium position, the motion of the object is simple harmonic motion. Mary says this is true only if the acceleration is opposite in direction to the displacement. Which one, if either, is correct
Answer:
Both Ellen and Mary are correct.
Explanation:
Both are correct, it's just different ways of saying the same thing.
When the acceleration is always opposite in direction to the displacement, then, the acceleration is directly proportional to the displacement of an object from its equilibrium position
A car is going 8 meters per second on an access road into a highway
and then accelerates at 1.8 meters per second squared for 7.2
seconds. How fast is it then going?
Answer:
20.96 m/s^2 (or 21)
Explanation:
Using the formula (final velocity - initial velocity)/time = acceleration, we can plug in values and manipulate the problem to give us the answer.
At first, we know a car is going 8 m/s, that is its initial velocity.
Then, we know the acceleration, which is 1.8 m/s/s
We also know the time, 7.2 second.
Plugging all of these values in shows us that we need to solve for final velocity. We can do so by manipulating the formula.
(final velocity - initial velocity) = time * acceleration
final velocity = time*acceleration + initial velocity
After plugging the found values in, we get 20.96 m/s/s, or 21 m/s
(a) If electrons were used (electron microscope), what minimum kinetic energy would be required for the electrons
Answer:
K = 1.6 10⁻¹⁵ J
Explanation:
In an electron microscope, electrons are used to form images, these electrons are accelerated in electric fields so that they have a kinetic energy that allows obtaining a good amplification with the microscope.
electrical potential energy is converted to kinetic energy
U = K
e V = ½ m v²
v = √2eV /m
the wavelength of these electrons we obtain from the de Broglie equation
λ = h / p
p = mv
λ = h / mv
λ = h / mra 2eV / m
λ = h / ra 2eVm
where we can see that as the potential energy increases, it electrifies the shorter the wavelength of the electrons and consequently the greater the magnification of the microscope
in general these microscopes use from 10000X onwards therefore for this saponification
K = e V
K = 1.6 10⁻¹⁹ 10000
K = 1.6 10⁻¹⁵ J
A merry-go-round spins freely when Diego moves quickly to the center along a radius of the merry-go-round. As he does this, it is true to say that
Answer:
A) the moment of inertia of the system decreases and the angular speed increases.
Explanation:
The complete question is
A merry-go-round spins freely when Diego moves quickly to the center along a radius of the merry-go-round. As he does this, It is true to say that
A) the moment of inertia of the system decreases and the angular speed increases.
B) the moment of inertia of the system decreases and the angular speed decreases.
C) the moment of inertia of the system decreases and the angular speed remains the same.
D) the moment of inertia of the system increases and the angular speed increases.
E) the moment of inertia of the system increases and the angular speed decreases
In angular momentum conservation, the initial angular momentum of the system is conserved, and is equal to the final angular momentum of the system. The equation of this angular momentum conservation is given as
[tex]I_{1} w_{1} = I_{2} w_{2}[/tex] ....1
where [tex]I_{1}[/tex] and [tex]I_{2}[/tex] are the initial and final moment of inertia respectively.
and [tex]w_{1}[/tex] and [tex]w_{2}[/tex] are the initial and final angular speed respectively.
Also, we know that the moment of inertia of a rotating body is given as
[tex]I = mr^{2}[/tex] ....2
where [tex]m[/tex] is the mass of the rotating body,
and [tex]r[/tex] is the radius of the rotating body from its center.
We can see from equation 2 that decreasing the radius of rotation of the body will decrease the moment of inertia of the body.
From equation 1, we see that in order for the angular momentum to be conserved, the decrease from [tex]I_{1}[/tex] to [tex]I_{2}[/tex] will cause the angular speed of the system to increase from [tex]w_{1}[/tex] to [tex]w_{2}[/tex] .
From this we can clearly see that reducing the radius of rotation will decrease the moment of inertia, and increase the angular speed.
An electron is moving at speed of 6.3 x 10^4 m/s in a circular path of radius of 1.7 cm inside a solenoid the magnetic field of the solenoid is perpendicular to the plane of the electron's path. Find its relevatn motion.
Answer:
Here, m=9×10
−31
kg,
q=1.6×10
−19
C,v=3×10
7
ms
−1
,
b=6×10
−4
T
r=
qB
mv
=
(1.6×10
−19
)(6×10
−4
)
(9×10
−31
)×(3×10
7
)
=0.28m
v=
2πr
v
=
2πm
Bq
=
2×(22/7)×9×10
−31
(6×10
−4
)×(1.6×10
−19
)
=1.7×10
7
Hz
Ek=
2
1
mv
2
=
2
1
×(9×10
−31
)×(3×10
7
)
2
J
=40.5×10
−17
J=
1.6×10
−16
40.5×10
−17
keV
=2.53keV
During World War II, mass spectrometers were used to separate the radioactive uranium isotope U-235 from its far more common isotope, U-238. Estimate the radius of the circle traced out by a singly ionized lead atom moving at the same speed.
Answer:
21.55 m
Explanation:
_____ is a distinct element found in Balinese Gamelan music in which a pair of gongs, one of them de-tuned, is played together, creating a sound similar to a tremolo.
its music btw
Answer:
best song ever will you follow me I will also follow you
A fish appears to be 2.00 m below the surface of a pond when viewed almost directly above by a fisherman. What is the actual depth of the fish
Answer:
2,66
Explanation:
The refractive index= real depth/ apparent depth
real depth = refractive index * apparent depth
Let's assume index for water is 1.33
real depth = 2*1,33 = 2,66
A generator consists of 1000 turns of wire around a coil of area 10cm2 (0.0010m 2 ). Calculate the peak output voltage of this generator when operating at 100 cycles/second in a 0.50 tesla field.
Answer:
The peak output voltage of this generator is 314.2 V.
Explanation:
Given;
the number of turns of the coil, N = 1000 turns
area of the coil, A = 0.001 m²
angular frequency of the coil, f = 100 cycles/seconds
magnitude of the magnetic field, B = 0.5 T
The peak output voltage of this generator is given by;
E = NBAω
Where;
ω is the angular velocity = 2πf
E = NBA(2πf)
E = 1000 x 0.5 x 0.001(2 x π x 100)
E = 314.2 V
Therefore, the peak output voltage of this generator is 314.2 V.
Find the minimum thickness (in nm) of a soap bubble that appears green when illuminated by white light perpendicular to its surface. Take the wavelength to be 549 nm, and assume the same index of refraction as water (nw
Answer:
103nm
Explanation:
Pls see attached file
What is the frequency of the fundamental mode of vibration of a steel piano wire stretched to a tension of 440 N? The wire is 0.630 m long and has a mass of 5.69 g.
Answer:
220.698HzExplanation:
The fundamental frequency f₀ is expressed as f₀ =V/2L where;
V is the speed of the string = [tex]\sqrt{\frac{T}{M} }[/tex]
m is the mass of the string
L is the length of the string
T is the tension in the string
f₀ = [tex]\frac{1}{2L} \sqrt{\frac{T}{m} }[/tex]
Given datas
m = 5.69g = 0.00569 kg
T = 440N
L = 0.630 m
Required
Fundamental frequency of the steel piano wire f₀
[tex]f_0 = \frac{1}{2(0.630)}\sqrt{\frac{440}{0.00569} } \\ \\f_0 = \frac{1}{1.26}\sqrt{77,328.65 } \\\\f_0 = \frac{1}{1.26} * 278.08\\\\f_0 = 220.698Hz[/tex]
Hence the frequency of the fundamental mode of vibration of the steel piano wire stretched to a tension of 440N is 220.698Hz
When light is either reflected or refracted, the quantity that does not change in either process is its
Answer:
Frequency
Explanation:
When waves travel from one medium to another, it is only the frequency of the wave that remains constant . when a wave is refracted at the boundary between two media, the wave will slow down and its wavelength decreases. The wave usually bends at the interface between the two media. The wavelength and speed of a wave may change at the boundary between two media but its frequency remains the same.
Hence the frequency of light is its only property that remains constant.
What is the momentum of a 36.9 N bowling ball with a velocity of 7.56 m/s?
Answer:
momentum (m)=36.9N
velocity (v)=7.56m/s
now,
momentum (m)=m×v
36.9=m×7.56
36.9÷7.56=m
m=4.89kg
Tech A says parallel circuits are like links in a chain. Tech B says total current in a parallel circuit equals the sum of the current flowing in each branch of the circuit. Who is correct?
Answer: Only Tech B is correct.
Explanation:
First, tech A is wrong.
The circuits that can be compared with links in a chain are the series circuit, and it can be related to the links in a chain because if one of the elements breaks, the current can not flow furthermore (because the elements in the circuit are connected in series) while in a parallel circuit if one of the branches breaks, the current still can flow by other branches.
Also in a parallel circuit, the sum of the currents of each path is equal to the current that comes from the source, so Tech B is correct, the total current is equal to the sum of the currents flowing in each branch of the circuit.
Alpha particles (charge = +2e, mass = 6.68 × 10-27 kg) are accelerated in a cyclotron to a final orbit radius of 0.30 m. The magnetic field in the cyclotron is 0.80 T. The period of the circular motion of the alpha particles is closest to: A. 0.25 μs B. 0.16 μs C. 0.49 μs D. 0.40 μs E. 0.33 μs
Answer:
Option B: T ≈ 0.16 μs
Explanation:
We are given;
Mass; m = 6.68 × 10^(-27) kg
Magnetic field;B = 0.80 T
Charge;q = 2e
Now, e is the charge on an electron and it has a value of 1.6 × 10^(-19) C
So, q = 2 × 1.6 × 10^(-19)
q = 3.2 × 10^(-19) C
The period of the circular motion of the alpha particles moving along a in the presence of the magnetic field is given by;
T = 2πm/qB
Where ;
m, q and B are as stated earlier.
Plugging in the relevant values, we have;
T = (2π × 6.68 × 10^(-27))/(3.2 × 10^(-19) × 0.8)
T = 0.16395 × 10^(-6) s
This can also be written as;
T ≈ 0.16 μs
What is the power P of the eye when viewing an object 61.0 cm away? Assume the lens-to-retina distance is 2.00 cm , and express the answer in diopters.
Answer:
The power of the eye is 51.64 diopters
Explanation:
The power of the eye is given by;
[tex]P = \frac{1}{f} = \frac{1}{d_o} +\frac{1}{d_i}[/tex]
where;
P is the power of the eye in diopter
f is the focal length of the eye
[tex]d_o[/tex] is the distance between the eye and the object
[tex]d_i[/tex] is the distance between the eye and the image
Given;
[tex]d_o[/tex] = 61.0 cm = 0.61 m
[tex]d_i[/tex] = 2.0 cm = 0.02 m
[tex]P = \frac{1}{d_o} +\frac{1}{d_i} \\\\P = \frac{1}{0.61} + \frac{1}{0.02} \\\\P = 51.64 \ D[/tex]
Therefore, the power of the eye is 51.64 diopters.
The power P of the eye when viewing an object 61.0 cm away is 51.639D
The power of a lens is a reciprocal of its focal length and it is expressed as:
[tex]P=\frac{1}{f}[/tex]
According to the mirror formula
[tex]\frac{1}{f} =\frac{1}{d_i} +\frac{1}{d_0}[/tex]
where
[tex]d_i[/tex] is the distance from the lens to the image = 61.0cm = 0.61m
[tex]d_0[/tex] is the distance from the lens to the object = 2.00cm = 0.02m
[tex]P=\frac{1}{f} =\frac{1}{0.02} +\frac{1}{0.61}\\P=50+1.639\\P=51.639D[/tex]
Hence the power P of the eye when viewing an object 61.0 cm away is 51.639D
Learn more here: https://brainly.com/question/14870552
The distance from the Sun to Earth is approximately 149,600,000 km. The distance from the Sun to Venus is approximately 108,200,000 km. The elongation angle αα is the angle formed between the line of sight from Earth to the Sun and the line of sight from Earth to Venus. Suppose that the elongation angle for Venus is 10∘.10 ∘. Use this information to find the possible distances between Earth and Venus.
Answer:
335206922km
Explanation:
Pls see attached file
which of the following can not happen when a light ray strikes a new medium
Answer:
amplification
Explanation:
reflection can happen
some amount of lighr get absorbed
something gets refracted
but amplification cant
krichoffs law of current questions
Answer:
Explanation:
Kirchhoff's Current Law, often shortened to KCL, states that “The algebraic sum of all currents entering and exiting a node must equal zero.
#I AM ILLITERATE
a coach is travelling east wards at 12.6 m/s after 12 second its velocity is 9.5 m/s in the same direction. what is the acceleration and direction of its acceleration?
pls do it with the formula
thx mates :)
[tex]\\ \rm\longmapsto a=\dfrac{v-u}{t}[/tex]
[tex]\\ \rm\longmapsto a=\dfrac{12.6-9.5}{12}[/tex]
[tex]\\ \rm\longmapsto a=\dfrac{3.1}{12}[/tex]
[tex]\\ \rm\longmapsto \overrightarrow{a}=0.25m/s^2[/tex]
Which is produced around a wire when an electrical current is in the wire? magnetic field solenoid electron flow electromagnet
Answer:
A. magnetic field
Explanation:
The magnetic field is produced around a wire when an electrical current is in the wire because of the magnetic effect of the electric current therefore the correct answer is option A .
What is a magnetic field ?A magnetic field could be understood as an area around a magnet, magnetic material, or an electric charge in which magnetic force is exerted.
As given in the problem statement we have to find out what is produced around a wire when an electrical current is in the wire.
The magnetic field is produced as a result when an electrical current is passed through the conducting wire .
Option A is the appropriate response because a wire's magnetic field is created when an electrical current flows through it due to the magnetic influence of the electric current .
Learn more about the magnetic fields here, refer to the link given below;
brainly.com/question/23096032
#SPJ6
2. The glass core of an optical fiber has an index of refraction 1.60. The index of refraction of the cladding is 1.48. What is the maximum angle a light ray can make with the wall of the core if it is to remain inside the fiber?
Answer:
We know that the maximum angle that a light ray can wake with the wall of the core is equipment to the minimum angle with the normal of the core that will give rise in total internal reflection. so using Snell's law the angle is subtracted from 90° to get the maximum angle a light ray can make with the wall of the core if it is to remain inside the fiber.
So using
n1sinစ1. = n2sinစ2
1.6sin(x1) = 1.48sin(90),
But sin(90)=1
1.6sin(စ1) = 1.48,
sin(စ1) = 1.48/1.6
စ = 68°
Explanation:
Answer:
i = 67.66⁰Explanation:
Using the Snell's law formula to solve this question which states that the ratio of the sine of angle of incidence to the sine of angle of refraction is a constant for a given pair of media. This constant is known as the refractive index for the given pair of media. Mathematically,
n = sin(i)/sin(r) where;
i is the angle of incidence
r is the angle of refraction.
n is the refractive index.
Given the refractive index of the optical fibre n₁ = 1.60 and that of cladding n₂ = 1.48
n₂/n₁ = sin(i)/sin(r)
The light ray can make with the wall of the core when its angle of refraction is 90⁰. The angle of incidence at this maximum point is known as the critical angle.
On substitution:
1.48/1.60 = sin(i)/sin90
1.48/1.60 = sin(i)/1
sin(i) = 1.48/1.60
sin(i) = 0.925
i = sin⁻¹0.925
i = 67.66⁰
Hence the maximum angle a light ray can make with the wall of the core if it is to remain inside the fiber is 67.66⁰.
An ac generator consists of a coil with 40 turns of wire, each with an area of 0.06 m2 . The coil rotates in a uniform magnetic field B = 0.4 T at a constant frequency of 55 Hz. What is the maximum induced emf?
a. 625 V
b. 110 V
c. 421 V
d. 332 V
e. 200 V
Answer:
d. 332 V
Explanation:
Given;
number of turns in the wire, N = 40 turns
area of the coil, A = 0.06 m²
magnitude of the magnetic field, B = 0.4 T
frequency of the wave, f = 55 Hz
The maximum emf induced in the coil is given by;
E = NBAω
Where;
ω is angular velocity = 2πf
E = NBA(2πf)
E = 40 x 0.4 x 0.06 x (2 x π x 55)
E = 332 V
Therefore, the maximum induced emf in the coil is 332 V.
The correct option is "D"
d. 332 V
1) True or False:
Atomic mass number is the number of neutrons and protons.
2) True or False:
Fe (iron) has 26 protons. Hint: protons equal what number?
3) True or False:
A photon of infrared light has less energy than a photon of red light.
Answer:
1.true
Explanation:
Answer:
1. True
2. True
3. True
Explanation for Question 1.
A nucleus consists of a bunch of protons and neutrons; these are known as nucleons. The atomic mass number, which is the total number of nucleons;
So, this sentence says that the atomic number is the number of protons and neutrons.
Explanation for Question 2.
Iron has 26 protons.
The number of protons = the atomic number.
So, the atomic number should be 26 also,
When we see the periodic table, Iron's atomic number is 26, so the statement is true.
Explanation for Question 3.
Red photons of light carry about 1.8 electron volts of energy. Infrared radiation has longer waves than red light, and thus oscillates at a lower frequency and carries less energy.
So, the above statement proves that the photon of infrared light has less energy than the photon of red light.
The left end of a long glass rod 8.00 cm in diameter and with an index of refraction of 1.60 is ground and polished to a convex hemispherical surface with a radius of 4.00 cm. An object in the form of an arrow 1.70 mm tall, at right angles to the axis of the rod, is located on the axis 24.0 cm to the left of the vertex of the convex surface.
A) Find the position of the image of the arrow formed by paraxial rays incident on the convex surface.
B) Find the height of the image formed by paraxial rays incident on the convex surface.
C) Is the image erect or inverted?
Answer:
A) 0.1477
B) 0.65388 mm
C) object is inverted
Explanation:
The formula for object - image relationships for spherical reflecting surface is given as;
n1/s + n2/s' = = (n2 - n1)/R
Where;
n1 & n2 are the Refractive index of both surfaces
s is the object distance from the vertex of the spherical surface
s' is the image distance from the vertex of the spherical surface
R is the radius of the spherical surface
We are given;
index of refraction of glass; n2 = 1.60
s = 24 cm = 0.24 m
R = 4 cm = 0.04 m
index of refraction of air has a standard value of 1. Thus; n1 = 1
a) So, making s' the subject from the initial equation, we have;
s' = n2/[((n2 - n1)/R) - n1/s]
Plugging in the relevant values, we have;
s' = 1.6/[((1.6 - 1)/0.04) - 1/0.24]
s' = 0.1477
b) The formula for lateral magnification of spherical reflecting surfaces is;
m = -(n1 × s')/(n2 × s) = y'/y
Where;
m is the magnification
n1, n2, s & s' remain as earlier explained
y is the height of the object
y' is the height of the image
Making y' the subject, we have;
y' = -(n1 × s' × y)/(n2 × s)
We are given y = 1.7 mm = 0.0017 m and all the other terms remain as before.
Thus;
y' = -(1 × 0.1477 × 0.0017)/(1.6 × 0.24)
y' = - 0.00065388021 m = -0.65388 mm
C) since y' is negative and y is positive therefore, m = y'/y would result in a negative value.
Now, in object - image relationships for spherical reflecting surface, when magnification is positive, it means the object is erect and when magnification is negative, it means the object is inverted.
Thus, the object is inverted since m is negative.
What would happen if you changed the position of the screen, but kept the other factors the same?
Answer:
I wish I could help but iam srry