Answer:
The discharge rate is [tex]Q = 0.0192 \ m^3 /s[/tex]
Explanation:
From the question we are told that
The diameter is [tex]d = 60 \ mm = 0.06 \ m[/tex]
The head is [tex]h = 6 \ m[/tex]
The coefficient of contraction is [tex]Cc = 0.68[/tex]
The coefficient of velocity is [tex]Cv = 0.92[/tex]
The radius is mathematically evaluated as
[tex]r = \frac{d}{2}[/tex]
substituting values
[tex]r = \frac{ 0.06 }{2}[/tex]
[tex]r = 0.03 \ m[/tex]
The area is mathematically represented as
[tex]A = \pi r^2[/tex]
substituting values
[tex]A = 3.142 * (0.03)^2[/tex]
[tex]A = 0.00283 \ m^2[/tex]
The discharge rate is mathematically represented as
[tex]Q = Cv *Cc * A * \sqrt{ 2 * g * h}[/tex]
substituting values
[tex]Q = 0.68 * 0.92* 0.00283 * \sqrt{ 2 * 9.8 * 6}[/tex]
[tex]Q = 0.0192 \ m^3 /s[/tex]
Sunlight reflected from a smooth ice surface is completely polarized. Determine the angle of incidence. (nice = 1.31.)
Answer:
Explanation:
We shall apply Brewster's law to solve the problem . Let i be the angle of reflection required. According to this law ,
tan i = μ where i is angle of incidence , μ is refractive index of the medium .
Here i = ? , μ = 1.31
tani = 1.31
i = 53° approx .
At the angle of 53° incidence , the reflected ray will be completely polarised .
Two buses 'A' and 'B' are moving in the same direction with the velocities 30m/s and 40m/s respectively. Find the relative velocity of the bus 'A' with respect to the bus 'B'. Calculate the relative displacement between them after 4 minutes.:)
Hope who are reading this may have a good life;)
Lots of love from Nepal <3
Relative Velocity, aVb:
[tex]{ \bf{ _{A} V_{B} =V_{A} - V_{B} }} \\ _{A} V_{B} = 30 - 40 \\ _{A} V_{B} = - 10 \: {ms}^{ - 1} \\ |_{A} V_{B}| = 10 \: {ms}^{ - 1} [/tex]
Relative displacement:
[tex] = \frac{ |_{A} V_{B}| }{time} \\ \\ = \frac{10}{4} \\ = 2.5 \: metres[/tex]
Three resistors, each having a resistance, R, are connected in parallel to a 1.50 V battery. If the resistors dissipate a total power of 3.00 W, what is the value of R
Answer:
The value of resistance of each resistor, R is 2.25 Ω
Explanation:
Given;
voltage across the three resistor, V = 1.5 V
power dissipated by the resistors, P = 3.00 W
the resistance of each resistor, = R
The effective resistance of the three resistors is given by;
R(effective) = R/3
Apply ohms law to determine the current delivered by the source;
V = IR
I = V/R
I = 3V/R
Also, power is calculated as;
P = IV
P = (3V/R) x V
P = 3V²/R
R = 3V² / P
R = (3 x 1.5²) / 3
R = 2.25 Ω
Therefore, the value of resistance of each resistor, R is 2.25 Ω
A circular coil of wire 8.40 cm in diameter has 17.0 turns and carries a current of 3.20 A . The coil is in a region where the magnetic field is 0.610 T.Required:a. What orientation of the coil gives the maximum torque on the coil ?b. What is this maximum torque in part (A) ?c. For what orientation of the coil is the magnitude of the torque 71.0 % of the maximum found in part (B)?
Answer:
a) for the torque to be maximum, sin should be maximum
i.e (sinФ)maximum = 1
b) therefore the Maximum torque is
Tmax = 0.1838 × 1 = 0.1838 N.m
c) Given the torque is 71.0% of its maximum value; Ф = 45.24⁰ ≈ 45⁰
Explanation:
Given that; Diameter is 8.40 cm,
Radius (R) = D/2 = 8.40/2 = 4.20 cm = 0.042 m
Number of turns (N) = 17
Current in the loop (I) = 3.20 A
Magnetic field (B) = 0.610 T
Let the angle between the loop's area vector A and the magnetic field B be
Now. the area of the loop is;
A = πR²
A = 3.14 ( 0.042 )²
A = 0.005539 m²
Torque on the loop (t) = NIABsinФ
t = 17 × 3.20 ×0.005539 × 0.610 × sinФ
t = 0.1838sinФ N.m
for the torque to be maximum, sin should be maximum
i.e (sinФ)maximum = 1
therefore the Maximum torque is
Tmax = 0.1838 × 1 = 0.1838 N.m
Given the torque is 71.0% of its maximum value
t = 0.71 × tmax
t = 0.71 × 0.1838
t = 0.1305
Now
0.1305 N.m = 0.1838 sinФ N.m
sinФ = 0.1305 / 0.1838
sinФ = 0.71001
Ф = sin⁻¹ 0.71001
Ф = 45.24⁰ ≈ 45⁰
What is a benefit of joining the YMCA instead of a private health club?
The YMCA has nicer equipment and buildings.The YMCA has nicer equipment and buildings. , ,
The YMCA is likely to be in an upscale neighborhood.The YMCA is likely to be in an upscale neighborhood. , ,
The YMCA is much more affordable.The YMCA is much more affordable. , ,
The YMCA has restaurants and spa services.
Answer:
Explanation:
This depends on where you are.
The YMCA where I grew up was affordable. Very. Or my mother would not have let me go.
Find the momentum of a particl with a mass of one gram moving with half the speed of light.
Answer:
129900
Explanation:
Given that
Mass of the particle, m = 1 g = 1*10^-3 kg
Speed of the particle, u = ½c
Speed of light, c = 3*10^8
To solve this, we will use the formula
p = ymu, where
y = √[1 - (u²/c²)]
Let's solve for y, first. We have
y = √[1 - (1.5*10^8²/3*10^8²)]
y = √(1 - ½²)
y = √(1 - ¼)
y = √0.75
y = 0.8660, using our newly gotten y, we use it to solve the final equation
p = ymu
p = 0.866 * 1*10^-3 * 1.5*10^8
p = 129900 kgm/s
thus, we have found that the momentum of the particle is 129900 kgm/s
What is the maximum speed (in units of m/s) with which a car can round a
flat horizontal curve of radius (r=60 m), if the coefficient of static friction between tires and
road is (0.4)?
A) 5
B) 15.5
€) 240
D) 25.1
Answer:
B) 15.5 m/s
Explanation:
r = 60m
μs = 0.4
using the formula max V = √r*g*μs (flat roadway)
v = sqrt(60 * 10 * 0.4)
v = 15.5 m/s
Six automobiles are initially traveling at the indicated velocities. The automobiles have different masses and velocities. The drivers step on the brakes and all automobiles are brought to rest.Automobile 1: 500kg, 10m/sAutomobile 2: 2000kg, 5m/sAutomobile 3: 500kg, 20m/sAutomobile 4: 1000kg, 20m/sAutomobile 5: 1000kg, 10m/sAutomobile 6: 4000kg, 5m/sRequired:a. Rank these automobiles based on the magnitude of their momentum before the brakes are applied, from largest to smallest.b. Rank these automobiles based on the magnitude of the impulse needed to stop them, from largest to smallest.c. Rank the automobiles based on the magnitude of the force needed to stop them, from largest to smallest.
Answer:
A. largest: (4000 kg, 5 m/s; 1000 kg, 20 m/s)
medium: (2000 kg, 5 m/s; 500 kg, 20 m/s; 1000 kg, 10 m/s)
smallest: (500 kg, 10 m/s)
B. largest: (4000 kg, 5 m/s; 1000 kg, 20 m/s)
medium: (2000 kg, 5 m/s; 500 kg, 20 m/s; 1000 kg, 10 m/s)
smallest: (500 kg, 10 m/s)
C. You can't say anything about the forces required until we know about the time frames required for each one to stop. So If they all stopped in the same time interval, then the rankings are the same.
How does the capacitance of capacitor vary with the dielectric resistant of a medium
Answer:
Every dielectric medium will have a dielectric (strength) constant.
For space / vacuum it is 1. For rest of the dielectric media, it is greater than 1. The capacitance of a capacitor filled with a material of dielectric constant k, is given by the relation:
C = k . C0 (where C0 is the capacitance with space / vacuum as the dielectric material in that capacitor which means no dielectric between the plates)
So, it clearly states that the higher the dielectric constant, the more the capacitance i.e. it is directly proportional to the dielectric strength.
Dielectric constant varies with temperature.
Explanation:
plz mark me as a brainliest
A wire carries current in the plane of this paper toward the top of the page. The wire experiences a ma netic force toward the right edge of the page. The direction of the magnetic field causing this force is:
A. in the plane of the page and toward the left edge
B. in the plane of the page and toward the bottom edge
C. upward out of the page
D. downward into the page
Answer:
D) True. In this case the thumb goes up the page, the fingers are extended out of the page and the palm points to the left
Explanation:
The magnetic force on a conductor is given by
F = i L x B
bold letters indicate vectors. We can write this expression in the form of magnitudes
F = i L B sin θ
The direction of the force can be found by the rule of the right hand, the thumb points in the direction of the current, the fingers extended in the direction of the magnetic field and the palm gives the direction of the force
Let's apply this expression to the case presented.
A) False. In this case the force is out of the page and is in contradiction with the real force
B) False. In this case the force is zero since the displacement of the current and the field would be parallel
C) False. In this case the force is to the left
D) True. In this case the thumb goes up the page, the fingers are extended out of the page and the palm points to the left
a skier starts at the top of a hill this hill is 100 meters in the air the hill is pictured below the skier has a mass of about 50kg using the law of conversation of energy determine the Pe and Ke at the various points a he is at his maximum height and not moving at point E he has come to a complete stop
Answer:
a) Em = Pe = 4.9 10⁴ J, b) K = 2.05 10⁴ J , c) K = 3.92 104 J ,
e) W_ friction = Em = 4.9 10⁴ J
Explanation:
The skier goes down the slope if we assume that there is no friction, the mechanical energy is conserved
Em = PE + K
where the potential energy is
PE = m g h
the kinetic energy is
K = ½ m v²
Let's write the mechanical energy at various points
a) Point A. It is the highest point of the entire system and as the skier is leaving his speed is zero
Em = Pe
Em = m g h
let's calculate
Em = 50 9.8 100
Em = 4.9 10⁴ J
b) Point B. This point is 60 m
Em = Pe + K
K = Em - Pe
K = 4.9 10⁴ - m g h_B
K = 4.9 10⁴ - 5 9.8 60
K = 4.9 10⁴ - 2.85 10⁴
K = 2.05 10⁴ J
c) point c. This point is 20 m
Em = Pe + K
K = Em -Pe = 4.9 10⁴ J - m g h_c
K = 4.9 10⁴ - 50 9.8 20 = 4.9 10⁴ - 9800
K = 3.92 104 J
d) point d. It is at a height of 60 m
Em = Pe + K
K = Em -Pe
K = 4.9 10⁴ - m g h
K = 4.9 10⁴ - 50 9.8 60 =4.9 104 - 2.94 10⁻⁴
K = 4.897 104 J
e) point E. In this part they indicate that the body is stopped, therefore in this flat part it must be friction so that a device work is carried out that makes the understanding transform into heat by friction and the system stops
W_ friction = Em = 4.9 10⁴ J
Suppose, we have a parallel plate capacitor and we know the following about it: Area of each plate = $0.0012m^2$ Distance between the two plates = $0.002m$ Charge on each plate after fully charging the capacitor = $2\times10^{-6}C$ Potential difference between the plates after fully charging the capacitor = $4\times 10^{-3}V$ My solution: We know that the electric field intensity at a point between two equally and oppositely charged plates is $\LARGE\frac{\sigma}{\epsilon_0}$. So, for the above case, $$\large E = \frac{\sigma}{\epsilon_0}$$ $$\large\implies E = \frac{\frac{2\times10^{-6}}{0.0012}}{8.85\times10^{-12}}{NC^{-1}}$$ $$\large\implies E =188323917.1NC^{-1}$$ My book's solution: $$E = \frac{V}{d}$$ $$\implies E=\frac{4\times 10^{-3}V}{0.002m}NC^{-1}$$ $$\implies E = 2NC^{-1}$$ If the books solution is correct, could you please explain why my answer is wrong and the book's is correct? Thanks in advance!
Answer:
udegsgsfsjtajtsiaitskhsigsfjsjgsyoeyodogdoydyosiskgoydoydiydiyddohdohdohyodhodohdoydoydoydosoydogdkgdohdhdohdgodyodoydoydyodoydyodoydohxohdohxohxohxohxogxkx skzjgz a few days
Light of wavelength 500 nm falls on two slits spaced 0.2 mm apart. If the spacing between the first and third dark fringes is to be 4.0 mm, what is the distance from the slits to a screen?
Answer:
L = 0.8 m
Explanation:
Since, the distance between first and third dark fringes is 4 mm. Therefore, the fringe spacing between consecutive dark fringes will be:
Δx = 4 mm/2 = 2 mm = 2 x 10⁻³ m
but,
Δx = λL/d
λ = wavelength of the light = 500 nm = 5 x 10⁻⁷ m
d = slit spacing = 0.2 mm = 0.2 x 10⁻³ m
L = Distance between slits and screen = ?
Therefore, using the values, we get:
2 x 10⁻³ m = (5 x 10⁻⁷ m)(L)/(0.2 x 10⁻³)
L = (2 x 10⁻³ m)(0.2 x 10⁻³ m)/(5 x 10⁻⁷ m)
L = 0.8 m
One charge is fixed q1 = 5 µC at the origin in a coordinate system, a second charge q2 = -3.2 µC the other is at a distance of x = 90 m from the origin.
What is the potential energy of this pair of charges?
Answer:
5.4uC
Explanation:
Distinguish between physical and chemical changes. Include examples in your explanations.
Answer:
Chemical changes are recognized when a substance changes its properties permanently and it cannot be the same substance as before.
Instead the physical changes implies that if you can return to the same substance through a reverse process.
Explanation:
A chemical change is, by example, a combustion, if a sheet of paper burns, its result is ashes, the ashes cannot go back to being a sheet of paper because its properties changed, heat energy was generated that changed matter permanently.
A physical change, by example, is that of freezing water, the water becomes ice, but this can easily become water again if the temperature is increased, its properties do not change and the chemistry of the substance does not change.
A chemical change takes place when a chemical reaction takes place, while when a matter changes forms but not the chemical identity then a physical change takes place.
• A product or a new compound formation takes place from a chemical change as the rearrangement of atoms takes place to produce novel chemical bonds.
• In a chemical change always a chemical reaction takes place.
• Some of the chemical changes examples are souring milk, burning wood, digesting food, mixing acid and base, cooking food, etc.
• In a physical change no new chemical species form.
• The changing of the state of a pure substance between liquid, gas, or solid is a physical change as there is no change in the identity of the matter.
• Some of the physical changes are melting of ice, tempering of steel, breaking a bottle, crumpling a sheet of aluminum foil, boiling water, and shredding paper.
Thus, a new substance is formed during a chemical change, while a physical change does not give rise to a new substance.
To know more about:
https://brainly.com/question/7279398
In part A of the lab we see that the magnetic field of a long straight wire __. a. increases with distance in a linear relationship b. increases with distance in a non-linear relationship c. decreases with distance in an inverse (1/r) relationship d. decreases with distance in an inverse-square (1/r2) relationship
Explanation:
a long straight wire __. a. increases with distance in a linear relationship b. increases with distance in a non-linear relationship c. decreases with distance in an inverse (1/r) relationship d. decreases with distance in an inverse-square (1/r2) relationship
In part A of the lab, we see the magnetic field of a long straight wire decreases with distance in an inverse (1/r) relationship, therefore the correct option is C.
What is a magnetic field?A magnetic field could be understood as an area around a magnet, magnetic material, or an electric charge in which magnetic force is exerted. The SI unit of the magnetic field is tesla.
For a long straight wire carrying the current, the relation with the distance as given below
B = μI/(2πr)
where B is the magnetic field
μ is the permeability of the free space
r is the distance from the wire
As we can see from the above relation
the magnetic field of a long straight wire decreases with distance in an inverse (1/r) relationship, therefore the correct answer is option C.
Learn more about the magnetic fields from here
brainly.com/question/23096032
#SPJ2
A light beam inside a container of some liquid hits the surface of the liquid/air interface. Depending on the angle, the light beam may or may not be able to get out into the air medium. At what angle will the beam of light be totally reflected back into the liquid in the container
Answer:
Following are the solution to the given question:
Explanation:
Applying the Snell Law:
when is the liquid's refractive index, is the air's refractive index.
the liquid's refractive index, the air's index of refraction.
It is the limiting case when , Inside the interphase of two mediums, light is scattered. Thus,
[tex]n_l \sin \theta_l = n_a \sin 90^\circ = n_a[/tex]
[tex]\theta_l = \arcsin \dfrac{n_a}{n_l} =\arcsin \dfrac{1}{1.38} = 46.4^\circ[/tex]
From the incident angles [tex]\theta_l[/tex] is greater than 46.4°, that is the light reflected back into the liquid.
Nuclear plants use radioactive fuel to produce steam which turns a turbine to generate electricity. This is an example of a(n) _____. A) heat pump B) heat mover C) internal combustion engine D) external combustion engine
Answer:
C) internal combustion engineExplanation:
A light beam is traveling through an unknown substance. When it strikes a boundary between that substance and the air (nair≈1), the angle of reflection is 29.0∘ and the angle of refraction is 39.0∘. What is the index of refraction n of the substance?
Answer:
0.7707
Explanation:
From Snell's law,
n(1) * sin θ1 = n(2) * sinθ2
Where n(1) = refractive index of air = 1.0003
θ1 = angle of incidence
n(2) = refractive index of second substance
θ2 = angle of refraction
The angle of reflection through the unknown substance is the same as the angle of incidence of air. Thus this means that θ1 = 29°
=> 1.0003 * sin29 = n(2) * sin39
n(2) = (1.0003 * sin29) / sin39
n(2) = 0.7707
Explanation:
The index of refraction n of the substance is 0.7707
Snell law:Here we know that
n(1) * sin θ1 = n(2) * sinθ2
here
n(1) = refractive index of air = 1.0003
θ1 = angle of incidence
n(2) = refractive index of second substance
θ2 = angle of refraction
The angle of reflection should be via the unknown substance that represent the same as the angle of incidence of air.
So,
θ1 = 29°
1.0003 * sin29 = n(2) * sin39
n(2) = (1.0003 * sin29) / sin39
n(2) = 0.7707
learn more about refraction here: https://brainly.com/question/21312906
The concentration of sodium and potassium ions in the blood and body fluid is regulated by :
Answer:
Kidney
Explanation:
One of the main function of the kidney is to maintain the homeostasis of sodium and potassium ions in the blood and body.
Aldosterone is a key steroid hormone that balances sodium and potassium ions in the blood and body fluid. Potassium and sodium ions generate electric impulse in the body which helps to perform different activities such as muscles flexing.
Kidney function for reabsorption and secretion, in which reabsorption of Na is done nd balances the sodium and potassium in the blood and body.
A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?
Complete Question
A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .
Part A. Calculate the coil's self-inductance.
Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.
Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?
Answer:
Part A
[tex]L = 0.000863 \ H[/tex]
Part B
[tex]\epsilon = 0.863 \ V[/tex]
Part C
From terminal a to terminal b
Explanation:
From the question we are told that
The number of turns is [tex]N = 590 \ turns[/tex]
The cross-sectional area is [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]
The radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]
Generally the coils self -inductance is mathematically represented as
[tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]
Where [tex]\mu_o[/tex] is the permeability of free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]
substituting values
[tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]
[tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]
[tex]L = 0.000863 \ H[/tex]
Considering the Part B
Initial current is [tex]I_1 = 5.00 \ A[/tex]
Current at time t is [tex]I_t = 3.0 \ A[/tex]
The time taken is [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]
The self-induced emf is mathematically evaluated as
[tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]
=> [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]
substituting values
[tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]
[tex]\epsilon = 0.863 \ V[/tex]
The direction of the induced emf is from a to b because according to Lenz's law the induced emf moves in the same direction as the current
This question involves the concepts of the self-inductance, induced emf, and Lenz's Law
A. The coil's self-inductance is "0.863 mH".
B. The self-induced emf in the coil is "0.58 volts".
C. The direction of the induced emf is "from b to a".
A.
The self-inductance of the coil is given by the following formula:
[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]
where,
L = self-inductance = ?
[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²
N = No. of turns = 590
A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²
r = radius = 5 cm = 0.05 m
Therefore,
[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]
L = 0.863 x 10⁻³ H = 0.863 mH
B.
The self-induced emf is given by the following formula:
[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]
where,
E = self-induced emf = ?
ΔI = change in current = 2 A
Δt = change in time = 3 ms = 0.003 s
Therefore,
[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]
E = 0.58 volts
C.
According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.
Learn more about Lenz's Law here:
https://brainly.com/question/12876458?referrer=searchResults
You have two capacitors and want to connect them across a voltage source (battery) to store the maximum amount of energy. Should they be connected in series or in parallel?
Answer:
In parallel
Explanation:
Ctotal = C1 + C2 + ... + Cn
A very long straight wire carries a 12 A current eastward and a second very long straight wire carries a 14 A current westward. The wires are parallel to each other and are 42 cm apart. Calculate the force on a 6.4 m length of one of the wires.
Answer: 5.12x10∧-4N
Explanation:
Force = I B L
L = 6.4m
Let Current (I) I₁ = I₂= 14A
Distance of the wire = 42cm = 0.42m
BUT
B = μ₀I / 2πr
=(2X10∧-7 X 12) / 0.42
B =5.714×10∧-6T
Force = I B L
Force = 14x [5.714×10-6]×6.4
Force = 5.12x10∧-4N
What happens to the magnetic field when you reverse the direction of current by sliding the battery voltage bar past 0 volts
Answer:
The polarity of the magnetic field changes
Explanation:
This because The magnetic field generated is always perpendicular to the direction of the current and parallel to the solonoid. Hence if we reverse the current the direction of magnetism also reverses. In other words the magnetic poles gets reversed (North pole becomes south pole and the south pole becomes the north pole)
A circuit contains a single 220 pF capacitor hooked across a battery. It is desired to store three times as much energy in a combination of two capacitors by adding a single capacitor to this one.
How would you hook it up?
The capacitor is connected in series to the original capacitor
or
The capacitor is connected in parallel to the original capacitor
I believe its parallel
but now What would its value be?
Answer
The capacitor should be connected in parallel as parallel connection gives the arithmetic sum of capacitance which will give a corresponding sum of energy while capacitors in series gives the sum of the reciprocal if the individual capacitance
A satellite in geostationary orbit is used to transmit data via electromagnetic radiation. The satellite is at a height of 35,000 km above the surface of the earth, and we assume it has an isotropic power output of 1.0 kW (although, in practice, satellite antennas transmit signals that are less powerful but more directional).
Required:
a. Reception devices pick up the variation in the electric field vector of the electromagnetic wave sent out by the satellite. Given the satellite specifications listed in the problem introduction, what is the amplitude E0 of the electric field vector of the satellite broadcast as measured at the surface of the earth? Use ϵ0=8.85×10^−12C/(V⋅m) for the permittivity of space and c=3.00×10^8m/s for the speed of light.
b. Imagine that the satellite described in the problem introduction is used to transmit television signals. You have a satellite TV reciever consisting of a circular dish of radius R which focuses the electromagnetic energy incident from the satellite onto a receiver which has a surface area of 5 cm^2. How large does the radius R of the dish have to be to achieve an electric field vector amplitude of 0.1 mV/m at the receiver?
Answer:
1. 6.99x 10^-6V/m
2. 18m
Explanation:
See attached file
A Cannonball is shot at an angle of 35.0 degrees and is in flight for 11.0 seconds before hitting the ground at the same height from which it was shot.
A. What is the magnitude of the inital velocity?B. What was the maximum height reached by the cannonball?C. How far, horizontally, did it travel?
Answer:
Explanation:
According to Equations of Projectile motion :
[tex]Time\ of\ Flight = \frac{2vsin(x)}{g}[/tex]
vsin(x) = 11 * 9.8 / 2 = 53.9 m/sec
(A) v (Initial velocity) = 11 * 9.8 / 2 * sin(35) = 94.56 m/sec
[tex]Maximum Height = \frac{(vsinx)^{2} }{2g}[/tex]
(B) Maximum Height = 53.9 * 53.9 / 2 * 9.8 = 142.2 m
[tex]Horizontal Range = vcosx * t[/tex]
(C) Horizontal Range = 94.56 * 0.81 * 11 = 842.52 m
A ferry boat sails east across a lake at 10 km/h. A woman is walking east on
the boat at 1.5 km/h. What is her speed relative to the boat?
A. 8.5 km/h west
B. 8.5 km/h east
C. 1.5 km/h east
O D. 1.5 km/h west
Answer:
B
8.5 km/h east
Explanation:
Relative velocity= Va -Vb
=10-1.5
=8.5 km/h east
The concept relative speed is used when two or more bodies moving with some speed are considered. The relative speed of woman to the boat is 8.5 km/h east. The correct option is B.
What is relative speed?The relative speed of two bodies is defined as the sum of their speeds if they are moving in the opposite direction and it is the difference of their speeds if they are moving in the same direction.
The speed of the moving body with respect to the stationary body is known as the relative speed. The term relative means in comparison to. The relative speed is a scalar quantity.
Here both the boat and women are travelling in the same direction. So the relative speed is given as:
Relative speed = 10 - 1.5 = 8.5 km / h
Therefore the relative speed is 8.5 km/h east.
Thus the correct option is B.
To know more about relative speed, visit;
https://brainly.com/question/11476119
#SPJ7
Give an example of a fad diet that is not healthy and one that is healthy. Explain how you know the difference.
Answer:
Good Diet: ! gallon of water a day, Fruits, Vegetables, White meats(Chicken), Don't eat past 3 PM.
Bad Diet: Pizza, Red meat, Baked goods, Eating at late hours.
Explanation: I know the difference because, When you drink water first thing in the morning it gets your metabolism running. Than means you can digest foods better, you want to feed your body good foods but you should not eat until you feel stuffed. You should eat until you are no longer starving. Than you should drink a cup of water in between meals. I know you should not eat past 3 pm because your body needs time to digest foods because you should never go to sleep with a full stomach. I know the difference between good food and bad food because when you eat healthy food and a balanced diet, your body will have more energy and you wont feel tired afterwards. Eating bad foods and food with artificial sugars will clump up in your kidneys, and your body will have small bursts of energy but you will feel lazy afterwards...Your body is supposed to stay energized from a healthy meal in order to give you the energy your body needs to exercise. If you feel droopy all the time and you don't want to do anything, than you are unhealthy.
Answer:
A vegetarian diet is an example of a good fad diet if you do it correctly. It can help you get lots of veggies and good nutrients from them while still following the non-meat diet you want. This can be effective and good for weight loss becasue you are still eating and getting all the good nutrients and calories from less fatty foods.
Vegan diet (some can be successful but many people fail and do not do good that is why I choose this) The problem with this fad diet is that it can cause nutritional deficiencies and lead to a host of additional health problems, including negatively impacting hormonal health and metabolism. Many people also struggle to find healthy vegan food and end up eating bad and fatty foods instead.
Explanation:
Got a 100
An electric train operates on 800 V. What is its power consumption when the current flowing through the train's motor is 2,130 A?
Answer:
1704 kWExplanation:
To solve for the power consumed by the trains motor we have to employ the formula for power which is
Power= current * voltage
Given that
voltage V= 800 V
current I= 2130 A
Substituting in the formula for power we have
Power= 2130*800= 1704000 watt
Power = 1704 kW
This is the amount of energy consumed, transferred or converted per unit of time
Hence the power consumed by the trains motor is 1704 kW