A viewing screen is separated from a double slit by 5.20 m. The distance between the two slits is 0.0300 mm. Monochromatic light is directed toward the double slit and forms an interference pattern on the screen. The first dark fringe is 3.70 cm from the center line on the screen.
Required:
a. Determine the wavelength of light.
b. Calculate the distance between the adjacent bright fringes.
Answers
Answer:
The wavelength of this light is approximately [tex]427\; \rm nm[/tex] ([tex]4.27\times 10^{-7}\; \rm m[/tex].)The distance between the first and central maxima is approximately [tex]7.40\; \rm cm[/tex] (about twice the distance between the first dark fringe and the central maximum.)Explanation:
WavelengthConvert all lengths to meters:
Separation of the two slits: [tex]0.0300\; \rm mm = 3.00\times 10^{-5}\; \rm m[/tex].Distance between the first dark fringe and the center of the screen: [tex]3.70\; \rm cm = 3.70\times 10^{-2}\; \rm m[/tex].Refer to the diagram attached (not to scale.) Assuming that the screen is parallel to the line joining the two slits. The following two angles are alternate interior angles and should be equal to each other:
The angle between the filter and the beam of light from the lower slit, andThe angle between the screen and that same beam of light.These two angles are marked with two grey sectors on the attached diagram. Let the value of these two angles be [tex]\theta[/tex].
The path difference between the two beams is approximately equal to the length of the segment highlighted in green. In order to produce the first dark fringe from the center of the screen (the first minimum,) the length of that segment should be [tex]\lambda / 2[/tex] (one-half the wavelength of the light.)
Therefore:
[tex]\displaystyle \cos \theta \approx \frac{\text{Path difference}}{\text{Slit separation}} = \frac{\lambda / 2}{3.00\times 10^{-5}\; \rm m}[/tex].
On the other hand:
[tex]\begin{aligned} \cot \theta &\approx \frac{\text{Distance between central peak and first minimum}}{\text{Distance between the screen and the slits}} \\ &= \frac{3.70\times 10^{-2}\; \rm m}{5.20\; \rm m} \approx 0.00711538\end{aligned}[/tex].
Because the cotangent of [tex]\theta[/tex] is very close to zero,
[tex]\cos \theta \approx \cot \theta \approx 0.00711538[/tex].
[tex]\displaystyle \frac{\lambda /2}{3.00\times 10^{-5}\; \rm m} \approx \cos\theta\approx 0.00711538[/tex].
[tex]\begin{aligned}\lambda &\approx 2\times 0.00711538 \times \left(3.00\times 10^{-5}\; \rm m\right) \\ &\approx 4.26 \times 10^{-7}\; \rm m = 426\; \rm nm\end{aligned}[/tex].
Distance between two adjacent maximaIf the path difference is increased by one wavelength, then the intersection of the two beams would move from one bright fringe to the next one.
The path difference required for the central maximum is [tex]0[/tex].The path difference required for the first maximum is [tex]\lambda[/tex].The path difference required for the second maximum is [tex]2\,\lambda[/tex].On the other hand, if the distance between the maximum and the center of the screen is much smaller than the distance between the screen and the filter, then:
[tex]\begin{aligned}&\frac{\text{Distance between image and center of screen}}{\text{Distance between the screen and the slits}} \\ &\approx \cot \theta \\ &\approx \cos \theta \\ &\approx \frac{\text{Path difference}}{\text{Slit separation}}\end{aligned}[/tex].
Under that assumption, the distance between the maximum and the center of the screen is approximately proportional to the path difference. The distance between the image (the first minimum) and the center of the screen is [tex]3.70\; \rm cm[/tex] when the path difference is [tex]\lambda / 2[/tex]. The path difference required for the first maximum is twice as much as that. Therefore, the distance between the first maximum and the center of the screen would be twice the difference between the first minimum and the center of the screen: [tex]2 \times 3.70\; \rm cm = 7.40\; \rm cm[/tex].
Related Questions
Suppose you want a telescope that would allow you to see distinguishing features as small as 3.5 km on the Moon some 384,000 km away. Assume an average wavelength of 550 nm for the light received.Required:What is the minimum diameter mirror on a telescope?
Answers
Explanation:
[tex]\theta=1.22 \frac{\lambda}{D}[/tex]
And, from equation ( 2 ), we get
[tex]\theta=\frac{x}{d}[/tex]
Thus,
[tex]\frac{x}{d} &=1.22 \frac{\lambda}{D}[/tex]
[tex]D &=1.22 \frac{\lambda d}{x}[/tex]
[tex]=1.22 \frac{550 \times 10^{-9} 3.84 \times 10^{8}}{5 \times 10^{3}}[/tex]
[tex]=0.0515 \mathrm{m}[/tex]
Thus, the diameter of the telescope's mirror that would allow us to see details as small as is
A 60 mAs results in an exposure of 85 mGya, with all factors remaining the same, what would the new exposure be if 120 mAs is used?
Answers
Answer: d₂ = 170 mGya
Explanation:
the relationship between absonbed 'd' and exposure 'E' is given as;
D(Gv) = F . x (AS/xB)
F is a conversion coefficient depending on medium
so we can simply write
d₁/d₂ = x₁/x₂
Given that;
our x₁ = 60 mAs, x₂ = 120 mAs, d₁ = 85 mGya, d₂ = ?
from the given formula,
d₂ = (x₂d₁ / x₁)
now we substitute
d₂ = (120 × 85) / 60
d₂ = 170 mGya
∴ if 120 mAa is used, the new exposure will be 170 mGya
Megan accelerates her skateboard from 0 m/s to 8 m/s in 2 seconds. What is the magnitude of the acceleration of the skateboard?
O 8 m/s^2
O 16 m/s^2
O 2 m/s^2
O 4 m/s^2
Answers
Answer:
chk picture for eqn
Explanation:
Calculate the electromotive force produced by each of the battery combinations shown in the figure, if the emf of each is 1.5 V.
Answers
Answer:
A) 1.5 V
B) 4.5 V
Explanation:
A) Batteries in parallel have the same voltage as an individual battery.
V = 1.5 V
B) Batteries in series have a voltage equal to the sum of the individual batteries.
V = 1.5 V + 1.5 V + 1.5 V
V = 4.5 V
Which of the units of the following physical quantities are derived
Answers
Answer:
You have not provided options but so long as the option is none of these, it's the right answer:
Electric current, Thermodynamic temperature,mass,time amount of substance,length, luminous intensity
A mass is tired to spring and begins vibration periodically the distance between it's lowest position is 48cm what is the Amplitude of the vibration
Answers
Answer:
The amplitude of vibration of the spring is "24 cm"
The periodic vibrating body's motion follows a sinusoidal path. This sinusoidal path is illustrated in the attached picture.
From the picture, it can be clearly seen that the amplitude of the periodic vibration motion is the distance from its mean position to the highest point.
Since the distance of both the highest and the lowest points from the mean position is the same. Therefore, the distance between the lowest and the highest point must be equal to two times the amplitude of the wave.
Amplitude = 24 cm
hi guys!!! i have no more points, can someone nice guess all of these for me? :)
1.What happens to the ocean water before the precipitation part of the water cycle
2.During which stage of the water cycle does water from the ocean form clouds?
3.what is a runoff??
4.Which statement about oceans is incorrect? A.Evaporation occurs when water is warmed by the sun. B.Most evaporation and precipitation occur over the ocean. C.97 percent of Earth's water is fresh water from the ocean. D.Water leaves the ocean by the process of evaporation
5.How does most ocean water return to the ocean in the water cycle
tysm to u who answers :)
Answers
1. The ocean water collects back in the ocean.
2. Condensation is the process by which water vapor in the air is changed into liquid water. Condensation is crucial to the water cycle because it is responsible for the formation of clouds.
3. an excessive amount of water flowing from downslope along earths surface
4. A.Evaporation occurs when water is warmed by the sun.
5. The water returns into the ocean by the water cycle . It evaporates , then it condensates , then it participates ( Rains ) and then goes back into the ocean.
Hope this answer correct ✌️
A mass is hanging from the end of a horizontal bar that pivots around an axis through its center, but it is being held stationary. The bar is then released and begins to rotate. As the bar rotates from horizontal to vertical, the magnitude of the torque on the bar: ________
Answers
Answer:
The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.
The torque decreases because as the hanging mass goes down, the moment arm about the pivot point decreases. Since the torque is directly proportional to the length of the moment arm, torque decreases.
What is the difference between atomic number and atomic mass ?Atomic number of an element is defined as total number of protons present in the nucleus, neutrons carry no net electrical charge, so it is the charge number of the nucleus.
atomic mass of an element can be defined as the atomic weight is measured total mass of an element’s atom, the total number of neutrons and protons in the nucleus of an atom.
Both Atomic mass and an atomic number of elements are closely related if atomic number is high, then the atomic mass is also said to be high.
For more details regarding fire mass , visit
brainly.com/question/16858932
#SPJ2
An electron has an initial velocity to the south but is observed to curve upward as the result of a magnetic field. This magnetic field must have a component:___________
a) north
b) upwards
c) downwards
d) east
e) west
Answers
Answer:
e) west
Explanation:
According to Lorentz left hand rule, the left hand is used to represent the motion of an electron in a magnetic field. Hold out the left hand with the fingers held out parallel to the palm, and the thumb held at right angle to the other fingers. If the thumb represents the motion of the electron though the field, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the particle.
In this case, if we point the thumb to the south (towards your body), with the palm facing up, then the fingers will point west.
The same force is applied to two hoops. The hoops have the same mass, but the larger hoop has twice the radius. How are the angular accelerations of the hoops related
Answers
Answer:
The angular accelerations of the hoops are related by the following equation [tex]\alpha _1 = 2\alpha_2[/tex].
Explanation:
Net force on the hoop is given by;
[tex]F_{net} = ma[/tex]
where;
a is linear acceleration
m is the mass
Net torque on the hoop is given by;
[tex]\tau_{net} =I\alpha[/tex]
where;
I is moment of inertia
α is the angular acceleration
But, τ = Fr
[tex]Fr = I \alpha\\\\\alpha = \frac{Fr}{I} \\\\\alpha = \frac{Fr}{mr^2} \\\\\alpha = \frac{F}{mr} \\\\\alpha = \frac{1}{r} (\frac{F}{m} )\\\\(since\ the \ force\ and \ mass \ are \ the \ same, \frac{F}{m} = constant=k)\\\\ \alpha = \frac{k}{r}\\\\k = \alpha r[/tex]
[tex]\alpha _1 r_1= \alpha_2 r_2[/tex]
let the angular acceleration of the smaller hoop = α₁
let the radius of the smaller hoop = r₁
then, the radius of the larger loop, r₂ = 2r₁
let the angular acceleration of the larger hoop = α₂
[tex]\alpha _1 r_1= \alpha_2 r_2\\\\\alpha_2= \frac{ \alpha _1 r_1}{r_2} \\\\\alpha_2=\frac{\alpha _1 r_1}{2r_1} \\\\\alpha_2= \frac{\alpha _1}{2} \\\\\alpha _1 = 2\alpha_2[/tex]
Therefore, the angular accelerations of the hoops are related by the following equation [tex]\alpha _1 = 2\alpha_2[/tex]
A fish in an aquarium with flat sides looks out at a hungry cat. To the fish, does the distance to the cat appear to be less than the actual distance, the same as the actual distance, or more than the actual distance? Explain.
Answers
Answer:
p = -q
he distance is equal to the current distance, so the distance does not change
Explanation:
For this exercise we can solve it using the equation of the constructor
1 / f = 1 / p + 1 / q
where f is the focal length, p the distance to the object and q the distance to the image
For a flat surface the radius is at infinity, therefore 1 / f = 0, which implies
1 / p = - 1 / q
p = -q
Therefore the distance is equal to the current distance, so the distance does not change
The magnitude of the magnetic field at point P for a certain electromagnetic wave is 2.12 μT. What is the magnitude of the electric field for that wave at P? (c = 3.0 × 108 m/s)
Answers
Answer:
The electric field is [tex]E = 636 \ V/m[/tex]
Explanation:
From the question we are told that
The magnitude of magnetic field is [tex]B = 2.12 \mu T = 2.12*10^{-6} \ T[/tex]
The value for speed of light is [tex]c = 3.0 *10^8 \ m/s[/tex]
Generally the magnitude of the electric field at point P is
[tex]E = B * c[/tex]
substituting values
[tex]E = 2.12 *10^{-6} * 3.0 *10^{8}[/tex]
[tex]E = 636 \ V/m[/tex]
The magnitude of electric field for the wave at point P is 636 V/m.
Given data:
The strength of magnetic field at point P is, [tex]B = 2.12 \;\rm \mu T=2.12 \times 10^{-6} \;\rm T[/tex].
The speed of light is, [tex]c = 3.0 \times 10^{8} \;\rm m/s[/tex].
The given problem is based on the concept of electric field and magnetic field. The electromagnetic wave works on the principle of oscillating magnetic field and electric field at the same region. We can find any of the two using the expression,
[tex]E = B \times c[/tex]
here,
E is the strength of electric field.
Solving as,
[tex]E = (2.12 \times 10^{-6}) \times (3 \times 10^{8})\\\\E = 636 \;\rm V/m[/tex]
Thus, we can conclude that the magnitude of electric field for the wave at point P is 636 V/m.
Learn more about the electric field here:
https://brainly.com/question/15800304
A double-slit experiment is performed with light of wavelength 620 nm. The bright interference fringes are spaced 2.3 mm apart on the viewing screen. What will the fringe spacing be if the light is changed to a wavelength of 360 nm?
Answers
Answer:
1.34 mm
Explanation:
A double slit experiment is conducted with a light which has a wavelength of 620 nm
The fringes are separated 2.3 mm apart
The light is changed to a wavelength length of 360 nm
Let x represent the fringe spacing as a result of the change in wavelength
Therefore,the fringe spacing can be calculated as follows
2.3mm/x= 620nm/360nm
Multiply both sides
x × 620= 2.3×360
620x= 828
x= 828/620
x= 1.34 mm
1. Rank the transformers on the basis of their rms secondary voltage. Rank from largest to smallest.
Vp = 240 V; Np = 1000 turns; Ns = 2000 turns
Vp = 480 V; Np = 4000 turns; Ns = 2000 turns
Vp = 480 V; Np = 2000 turns; Ns = 1000 turns
Vp = 120 V; Np = 500 turns; Ns = 2000 turns
Vp = 240 V; Np = 1000 turns; Ns = 500 turns
2. 100 A of rms current is incident on the primary side of each transformer. Rank the transformers on the basis of their rms secondary current. Rank from largest to smallest.
Vp = 240 V; Np = 1000 turns; Ns = 2000 turns
Vp = 480 V; Np = 2000 turns; Ns = 1000 turns
Vp = 240 V; Np = 1000 turns; Ns = 500 turns
Vp = 120 V; Np = 500 turns; Ns = 2000 turns
Vp = 480 V; Np = 4000 turns; Ns = 2000 turns
Answers
Answer:
1. Transformer 3> Transformer 1 and 2 > Transformer 4
2. Transformer 2,3,5 > Transformer 1 > Transformer 4
Explanation:
From;
Vs/Vp = Ns/Np
Where;
Vp= voltage in primary coil
Vs= voltage in secondary coil
Ns= number of turns in secondary coil
Np= number of turns in primary coil.
Vs= Ns×Vp/Np
Vs= 480 ×2000/4000
Vs= 240 V
Vs= 480 ×1000/2000
Vs=240 V
Vs= 120 × 2000/500
Vs= 480 V
Vs= 240 × 500/1000
Vs= 120 V
2. Ns/Np= Ip/Is
Is= Np×Ip/Ns
Is= 1000 × 100/2000
Is= 50 A
Is= 2000 × 100/1000
Is= 200 A
Is= 1000 × 100/500
Is= 200 A
Is= 500 × 100/2000
Is= 25 A
Is= 4000 × 100/2000
Is= 200 A
A person is being pulled by gravity with a force of 500 N. What is the force with which the person pulls Earth?
1,000 N
O100 N
500 N
0 250 N
Answers
Answer:
The correct answer is 500 N
Explanation:
This is an exercise in Newton's third law or law of action and reaction
The Earth exerts a force on the person, which we call a weight of 500 N directed downwards, we can call this action and the person exerts a force on the Earth of equal magnitude 500N and in the opposite direction, that is directed upwards.
Which force we call action does not matter, the analysis and conclusions are the same
The correct answer is 500N
the molecule of magnet are independent _____________
Answers
Answer:
The first is the electric field, which describes the force acting on a stationary charge and gives the component of the force that is independent of motion. The magnetic field, in contrast, describes the component of the force that is proportional to both the speed and direction of charged particles.
When the atmosphere is not quite clear, one may sometimes see colored circles concentric with the Sun or the Moon. These are generally not more than a few diameters of the Sun or Moon and invariably the innermost ring is blue. The explanation for these phenomena involves:_________
A) reflection
B) refraction
C) interference
D) diffraction
E) Doppler effect
Answers
Answer:
D) diffraction
Explanation:
Corona is an optical phenomenon produced by the diffraction of sunlight or moonlight, as light moves through water droplets in the atmosphere.
This phenomenon produces one or more diffuse concentric rings of light around the Sun or Moon, usually seen as colored circles.
Therefore, the explanation for these phenomena of colored concentric circles, sometimes seen with the Sun or the Moon involves diffraction.
A 13.6 kg block is tied at the top of an incline to a tree. If the incline is 35.5 degrees and the coefficient of friction between the sled and the incline is .45, What is the tension force between the block and the tree
Answers
Answer:
Explanation:
ASSUMING that block = sled AND that the rope is parallel to the slope.
The force acting parallel due to the weight is
13.6(9.81)sin35.5 = 77.475 N
The maximum friction force is
(0.45)13.6(9.81)cos35.5 = 48.877 N
If rope tension is T
77.475 - 48.877 < T < 77.475 + 48.877
28.6 N < T < 126 N
28.6 N will occur if the block is on the verge of sliding downhill
126 N will occur if the block is on the verge of sliding uphill
Could be any value between them.
A bicyclist moves along a straight line with an initial velocity vo and slows downs. Which of the following the best describes the signs set for the initial position, initial velocity and the acceleration ?
Answers
The sign set after the slowdown of the bicycle will be positive for the position, negative for velocity, and negative for acceleration.
What is velocity?The rate at which an object's position changes when observed from a specific point of view and when measured against a specific unit of time is known as its velocity.
According to Que, when a bicyclist moves in a straight line and slows down, then the velocity decrease as displacement is decreasing, and the acceleration also decreases only displacement increases.
Therefore, the sign set for the position is +ve, for velocity it is -ve, and for acceleration also -ve
To know more about Velocity:
https://brainly.com/question/19979064
#SPJ1
A biker slows down after traveling in a long, straight line at initial velocity v0. Which of the following the best \sdescribes the signs set for the initial position, initial velocity and the acceleration? Initial position Initial velocity Acceleration
A. Positive Negative Negative
B. Positive Positive Negative
C. Negative Positive Negative
D. Negative Negative Positive
E. Negative Negative Negative
A concrete slab shown in Figure 5 is being lifted by using three cables connected to the slab at points A, B and C. The slab is in the xy plane. The vertical force required to lift this slab is 60 kN (F 60 kN). Find the tensions in cables DA, DB and DC (show all your workings that you do to find these)
Answers
Answer:
Fad = 28.8 kN
Fbd = 16.4 kN
Fcd = 28.1 kN
Explanation:
First, find the length of each cable.
AD = √((2 m)² + (0.5 m)² + (2.5 m)²)
AD = √10.5 m
AD ≈ 3.24 m
BD = √((1.5 m)² + (1 m)² + (2.5 m)²)
BD = √9.5 m
BD ≈ 3.08 m
CD = √((1 m)² + (1 m)² + (2.5 m)²)
CD = √8.25 m
CD ≈ 2.87 m
Next, use similar triangles to find the x, y, and z components of each tension force.
Fadx = 2/3.24 Fad = 0.617 Fad
Fady = 0.5/3.24 Fad = 0.154 Fad
Fadz = 2.5/3.24 Fad = 0.772 Fad
Fbdx = 1.5/3.08 Fbd = 0.487 Fbd
Fbdy = 1/3.08 Fbd = 0.324 Fbd
Fbdz = 2.5 / 3.08 Fbd = 0.811 Fbd
Fcdx = 1/2.87 Fcd = 0.348 Fcd
Fcdy = 1/2.87 Fcd = 0.348 Fcd
Fcdz = 2.5/2.87 Fcd = 0.870 Fcd
Now sum the forces in the x, y, and z directions:
∑Fx = ma
-0.617 Fad + 0.487 Fbd + 0.348 Fcd = 0
∑Fy = ma
-0.154 Fad − 0.324 Fbd + 0.348 Fcd = 0
∑Fz = ma
60 kN − 0.772 Fad − 0.811 Fbd − 0.870 Fcd = 0
To solve this system of equations algebraically, start by subtracting the first two equations, eliminating Fcd.
-0.463 Fad + 0.811 Fbd = 0
0.811 Fbd = 0.463 Fad
Fbd = 0.571 Fad
Substitute into either of the first two equations:
-0.617 Fad + 0.487 (0.571 Fad) + 0.348 Fcd = 0
-0.617 Fad + 0.278 Fad + 0.348 Fcd = 0
-0.339 Fad + 0.348 Fcd = 0
0.348 Fcd = 0.339 Fad
Fcd = 0.975 Fad
Now substituting into the third equation:
60 kN − 0.772 Fad − 0.811 Fbd − 0.870 Fcd = 0
60 kN − 0.772 Fad − 0.811 (0.571 Fad) − 0.870 (0.975 Fad) = 0
60 kN − 0.772 Fad − 0.463 Fad − 0.849 Fad = 0
60 kN − 2.083 Fad = 0
Fad = 28.8 kN
Solving for the other two tension forces:
Fbd = 0.571 Fad = 16.4 kN
Fcd = 0.975 Fad = 28.1 kN
Answer:
Tensions of:
DA = 28.81 KN
DB = 16.45 KN
DC = 28.07 KN
Explanation:
see attached
You stand 17.5 m from a wall holding a softball. You throw the softball at the wall at an angle of 38.5∘ from the ground with an initial speed of 27.5 m/s. At what height above its initial position does the softball hit the wall? Ignore any effects of air resistance.
Answers
The ball's horizontal position in the air is
[tex]x=\left(27.5\dfrac{\rm m}{\rm s}\right)\cos38.5^\circ t[/tex]
It hits the wall when [tex]x=17.5\,\mathrm m[/tex], which happens at
[tex]17.5\,\mathrm m=\left(27.5\dfrac{\rm m}{\rm s}\right)\cos38.5^\circ t\implies t\approx0.813\,\mathrm s[/tex]
Meanwhile, the ball's vertical position is
[tex]y=\left(27.5\dfrac{\rm m}{\rm s}\right)\sin38.5^\circ t-\dfrac g2t^2[/tex]
where [tex]g[/tex] is the acceleration due to gravity, 9.80 m/s^2.
At the time the ball hits the wall, its vertical position (relative to its initial position) is
[tex]y=\left(27.5\dfrac{\rm m}{\rm s}\right)\sin38.5^\circ(0.813\,\mathrm s)-\dfrac g2(0.813\,\mathrm s)^2\approx\boxed{10.7\,\mathrm m}[/tex]
What is the de Broglie wavelength of an object with a mass of 2.50 kg moving at a speed of 2.70 m/s? (Useful constant: h = 6.63×10-34 Js.)
Answers
Answer:
9.82 × [tex]10^{-35}[/tex] Hz
Explanation:
De Broglie equation is used to determine the wavelength of a particle (e.g electron) in motion. It is given as:
λ = [tex]\frac{h}{mv}[/tex]
where: λ is the required wavelength of the moving electron, h is the Planck's constant, m is the mass of the particle, v is its speed.
Given that: h = 6.63 ×[tex]10^{-34}[/tex] Js, m = 2.50 kg, v = 2.70 m/s, the wavelength, λ, can be determined as follows;
λ = [tex]\frac{h}{mv}[/tex]
= [tex]\frac{6.63*10^{-34} }{2.5*2.7}[/tex]
= [tex]\frac{6.63 * 10^{-34} }{6.75}[/tex]
= 9.8222 × [tex]10^{-35}[/tex]
The wavelength of the object is 9.82 × [tex]10^{-35}[/tex] Hz.
In which example is kinetic friction most involved? a sled stuck on a snowy hill a bottle of water wedged in a vending machine an explorer unsuccessfully pushing on a massive stone that is blocking the entrance to a cave a volleyball player sliding across the court while diving for the ball
Answers
Answer:
I believe the answer is A volleyball player sliding across the court while diving for the ball.
Explanation:
Kinetic friction is a body moving on the surface experiences a force in the opposite direction of its movement.
Hope this helps! （づ￣3￣）づ╭❤～
The kinetic energy of an object with a mass of 6.8 kg and a velocity of 5.0 m/s is J. (Report the answer to two significant figures.)
Answers
Answer:
[tex] \boxed{\sf Kinetic \ energy \ (KE) = 85 \ J} [/tex]
Given:
Mass (m) = 6.8 kg
Speed (v) = 5.0 m/s
To Find:
Kinetic energy (KE)
Explanation:
Formula:
[tex] \boxed{ \bold{\sf KE = \frac{1}{2} m {v}^{2} }}[/tex]
Substituting values of m & v in the equation:
[tex] \sf \implies KE = \frac{1}{2} \times 6.8 \times {5}^{2} [/tex]
[tex] \sf \implies KE = \frac{1}{ \cancel{2}} \times \cancel{2} \times 3.4 \times 25 [/tex]
[tex] \sf \implies KE =3.4 \times 25 [/tex]
[tex] \sf \implies KE = 85 \: J[/tex]
The kinetic energy of the object reported to two significant figures is: 85 Joules.
Given the following data:
Mass = 6.8 kg Velocity = 5.0 m/s.To find the kinetic energy of the object:
Kinetic energy refers to an energy that is possessed by a physical object or body due to its motion.
Mathematically, kinetic energy is calculated by using the formula;
[tex]K.E = \frac{1}{2} MV^2[/tex]
Where:
K.E is the kinetic energy. M is the mass of an object. V is the velocity of an object.Substituting the parameters into the formula, we have;
[tex]K.E = \frac{1}{2}[/tex] × [tex]6.8[/tex] × [tex]5^2[/tex]
[tex]K.E = 3.4[/tex] × [tex]25[/tex]
Kinetic energy = 85 Joules.
Therefore, the kinetic energy of the object is 85 Joules.
Read more: https://brainly.com/question/23153766
Describe the forces that act on a skydiver before
and after the parachute is opened.
I will give brainliest!!!!
Answers
Answer:
Before the parachute opens: Immediately on leaving the aircraft, the skydiver accelerates downwards due to the force of gravity. There is no air resistance acting in the upwards direction, and there is a resultant force acting downwards. The skydiver accelerates towards the ground.
Once the parachute is opened, the air resistance overwhelms the downward force of gravity. The net force and the acceleration on the falling skydiver is upward. An upward net force on a downward falling object would cause that object to slow down. The skydiver thus slows down.
I HOPE THIS WILL HELP YOU IF NOT THEN SORRYHAVE A GREAT DAY :)
The main purpose of a written report may be to _____. A. revise a hypothesis B. summarize other scientists' results C. design a procedure for an experiment D. analyze data without drawing conclusions
PLZZZ HURRY TIMED MARK BRAINLIEST
Answers
Answer:
analyze data without drawing conclusions
Explanation:
Research reports are written in order to communicate clearly, information obtained primarily from research and analysis of data.
Typical reports of scientific research endeavours are written in such a way that they convey the research process succinctly without excessive extraneous information. A report is typically made up of; summary of the contents, introduction/ background, methods, results, discussion, conclusion and recommendations.
Hence a report does not really make inferences from the research findings.
A resistor and a capacitor are connected in series to an ideal battery of constant terminal voltage. At the moment contact is made with the battery, the voltage across the resistor is
Answers
Answer:
At the moment contact is made with the battery, the voltage across the resistor is equal to the batteries terminal voltage
Explanation;
Because at series connection the battery and resistor have equal voltage
c) If the ice block (no penguins) is pressed down even with the surface and then released, it will bounce up and down, until friction causes it to settle back to the equilibrium position. Ignoring friction, what maximum height will it reach above the surface
Answers
Answer:
y = 20.99 V / A
there is no friction y = 20.99 h
Explanation:
Let's solve this exercise in parts: first find the thrust on the block when it is submerged and then use the conservation of energy
when the block of ice is submerged it is subjected to two forces its weight hydrostatic thrust
F_net= ∑F = B-W
the expression stop pushing is
B = ρ_water g V_ice
where rho_water is the density of pure water that we take as 1 10³ kg / m³ and V is the volume d of the submerged ice
We can write the weight of the body as a function of its density rho_hielo = 0.913 10³ kg / m³
W = ρ-ice g V
F_net = (ρ_water - ρ_ ice) g V
this is the net force directed upwards, we can find the potential energy with the expression
F = -dU / dy
ΔU = - ∫ F dy
ΔU = - (ρ_water - ρ_ ice) g ∫ (A dy) dy
ΔU = - (ρ_water - ρ_ ice) g A y² / 2
we evaluate between the limits y = 0, U = 0, that is, the potential energy is zero at the surface
U_ice = (ρ_water - ρ_ ice) g A y² / 2
now we can use the conservation of mechanical energy
starting point. Ice depth point
Em₀ = U_ice = (ρ_water - ρ_ ice) g A y² / 2
final point. Highest point of the block
[tex]Em_{f}[/tex] = U = m g y
as there is no friction, energy is conserved
Em₀ = Em_{f}
(ρ_water - ρ_ ice) g A y² / 2 = mg y
let's write the weight of the block as a function of its density
ρ_ice = m / V
m = ρ_ice V
we substitute
(ρ_water - ρ_ ice) g A y² / 2 = ρ_ice V g y
y = ρ_ice / (ρ_water - ρ_ ice) 2 V / A
let's substitute the values
y = 0.913 / (1 - 0.913) 2 V / A
y = 20.99 V / A
This is the height that the lower part of the block rises in the air, we see that it depends on the relationship between volume and area, which gives great influence if there is friction, as in this case it is indicated that there is no friction
V / A = h
where h is the height of the block
y = 20.99 h
What is the direction of the net gravitational force on the mass at the origin due to the other two masses?
Answers
Answer:
genus yds it's the
Explanation:
xmgxfjxfjxgdfjusufzjyhmfndVFHggssjtjhryfjftjsrhrythhrsrhrhsfhsgdagdah vhj
An organ pipe open at both ends has two successive harmonics with frequencies of 220 Hz and 240 Hz. What is the length of the pipe? The speed of sound is 343 m/s in air.
Answers
Answer:
The length is [tex]l = 8.6 \ m[/tex]
Explanation:
From the question we are told that
The frequencies of the two successive harmonics are [tex]f_1 = 220 \ Hz[/tex] , [tex]f_2 = 240 \ Hz[/tex]
The speed of sound in the air is [tex]v_s = 343 \ m/s[/tex]
Generally the frequency of a given harmonic is mathematically represented as
[tex]f_n = \frac{n v }{2l}[/tex]
Here n defines the position of the harmonics
Now since the position of both harmonic is not know but we know that they successive then we can represented them mathematically as
[tex]220 = \frac{n v}{2l}[/tex]
and
[tex]240 = \frac{(n+1) v}{2l}[/tex]
So
[tex]\frac{(n + 1 ) v}{2l} - \frac{n v}{2l} = 240-220[/tex]
=> [tex]\frac{v}{2l} = 20[/tex]
=> [tex]l = 8.6 \ m[/tex]