Ayudaaa :(
Calcula la resistencia total del siguiente circuito eléctrico.

Answer:

velocity of ship wrt sea= 7i∧

velocity of women on deck= 40j∧

velocity of women relative to sea will be resultant of above two velocoties,

7i∧ + 40j∧ magnitude is

square root (7 x 7 + 40x40)

=√49+1600

=√1612

=40.14 m/s

Answer:

4) oscillator

Explanation:

4) oscillator

Answer:

Therefore the characteristics to be found are:

* the focal length must be large and the focal length of the eyepiece must be small

* The diameter of the objective lens should be as large as possible, to be able to collect small without need from light

* The system must be configured to the far sight tip,

Explanation:

The length of the telescope is

         L = f_ocular + f_objetive

the magnification of the telescope is

         m = - f_objective / f_ocular

These are the two equations that describe the behavior of the telescope. Therefore the characteristics to be found are:

* the focal length must be large and the focal length of the eyepiece must be small

* The diameter of the objective lens should be as large as possible, to be able to collect small without need from light

* The system must be configured to the far sight tip,

Answer:

The rms current in the circuit is 3.513 A

Explanation:

Given;

angular frequency of the inductor, ω = 363 rad/s

maximum voltage of the inductive AC, V₀ = 169 V

Inductance of the inductor, L = 0.0937 H

Inductive reactance is given by;

[tex]X_L = 2\pi f L= \omega L[/tex]

[tex]X_L = 363 *0.0937\\\\X_L = 34.0131 \ ohms[/tex]

The rms voltage is given by;

[tex]V_{rms} = \frac{V_o}{\sqrt{2} } \\\\V_{rms} =\frac{169}{\sqrt{2} } \\\\V_{rms} = 119.5 \ V[/tex]

The rms current in the circuit is given by;

[tex]I_{rms} = \frac{V_{rms}}{X_L} \\\\I_{rms} = \frac{119.5}{34.0131} \\\\I_{rms} = 3.513 \ A[/tex]

Therefore, the rms current in the circuit is 3.513 A

Answer:

e. It is neither attracted nor repelled.

Explanation:

Electrostatic attraction or repulsion occurs between two or more charged particles or conductors. In this case, if the negatively charged ball is brought close to the neutral end A of the rod, there would be no attraction or repulsion between the rod end A and the negatively charged ball. This is because a charged particle or conductor has no attraction or repulsion to a neutral particle or conductor.

Answer:

i) 545.2 N  upwards

ii) 828.2 N  downwards

Explanation:

mass of the roller = 70 kg

force exerted = 200 N

angle the force makes with the ground ∅ = 45°

weight of the roller W = mg

where

m is the mass of the roller

g is the acceleration due to gravity = 9.81 m/s^2

weight of the roller = 70 x 9.81 = 686.7 N

The effective vertical force exerted by the man = F sin ∅ = 200 x sin 45°

==> F = 200 x 0.707 = 141.5 N

i) if the man pulls, then the exerted force will be in opposite direction to the weight of the roller vertically upwards

Resultant vertical force = 686.7 N - 141.5 N = 545.2 N  upwards

ii) if he pushes, then the exerted force will be in the direction of the weight vertically downwards

Resultant vertical force = 686.7 N + 141.5 N = 828.2 N  downwards

Answer:

96 m

Explanation:

Given:

v₀ = 0 m/s

a = 3 m/s²

t = 8 s

Find: Δx

Δx = v₀ t + ½ at²

Δx = (0 m/s) (8 s) + ½ (3 m/s²) (8 s)²

Δx = 96 m

Explanation:

One of the most common uses for transistors in an electronic circuit is as simple switches. In short, a transistor conducts current across the collector-emitter path only when a voltage is applied to the base. When no base voltage is present, the switch is off. When base voltage is present, the switch is on.

Answer:

a)14Hz

b)26.6m/s

Explanation:

a)we were given

the first harmonics frequencies as 280 Hz

The second harmonic frequency as 294 Hz.

The fundamental frequency is equal to the gap which means the distance that exist between the harmonics, then

the fundamental frequency=(294 - 280 = 10 Hz)

= 14Hz

b) We know the frequency and the wavelength of the sound wave (

We were told that the wavelength must be twice the length of the tube then, velocity can be calculated as

And fundamental frequency= 14Hz, and distance of 1.90 m then

v = f*2L = (14Hz)*2*(1.90 m) = 26.6m/s

Therefore, the speed of sound in the gas in the tubes is 26.6m/s

Answer:

The initial kinetic energy of the bullet is closest to 491.87 J

Explanation:

Given;

mass of bullet, m₁ = 18g = 0.018kg

mass of block, m₂ = 10kg

height moved by the block, h = 9 mm = 0.009 m

time taken for the bullet to travel through the block, t = 0.001s

let the initial velocity of the bullet = v₁

let the final velocity of the bullet = v₂

Apply the principle of conservation of linear momentum;

initial momentum = final momentum

0.018v₁ = v₂(0.018 + 10)

0.018v₁ = 10.018v₂ -----equation (1)

Apply the law of conservation of energy when the bullet lifts the block through 9mm

mgh = ¹/₂mv₂²

gh = ¹/₂v₂²

v₂² = 2gh

v₂ = √2gh

v₂ = √(2 x 9.8 x 0.009)

v₂ = 0.42 m/s

Substitute in v₂ in equation 1, to determine the initial velocity of the bullet;

0.018v₁ = 10.018v₂

0.018v₁  =  10.018(0.42)

0.018v₁  = 4.208

v₁ = 4.208 / 0.018

v₁ = 233.78 m/s

Now, determine the initial kinetic energy of the bullet;

K.E₁ = ¹/₂m₁v₁²

K.E₁ = ¹/₂(0.018)(233.78)²

K.E₁ = 491.87 J

Therefore, the initial kinetic energy of the bullet is closest to 491.87 J

Answer:

4.245s

Explanation:

Given that,

Hypothetical value of speed of light in a vacuum is 18 m/s

Speed of the car, 14 m/s

Time given is 6.76 s, and we're asked to find the observed time, T

The relationship between the two times can be given as

T = t / √[1 - (v²/c²)]

The missing variable were looking for is t, and we can find it if we rearrange the formula and make t the subject

t = T / √[1 - (v²/c²)]

And now, we substitute the values and insert into the equation

t = 6.76 * √[1 - (14²/18²)]

t = 6.76 * √[1 - (196/324)]

t = 6.76 * √(1 - 0.605)

t = 6.76 * √0.395

t = 6.76 * 0.628

t = 4.245 s

Therefore, the time the driver measures for the trip is 4.245s

Answer:

Net force = 2.3686 × 10^(20) N

Explanation:

To solve this, we have to find the force of the earth acting on the moon and the force of the sun acting on the moon and find the difference.

Now, from standards;

Mass of earth;M_e = 5.98 × 10^(24) kg

Mass of moon;M_m = 7.36 × 10^(22) kg

Mass of sun;M_s = 1.99 × 10^(30) kg

Distance between the sun and earth;d_se = 1.5 × 10^(11) m

Distance between moon and earth;d_em = 3.84 × 10^(8) m

Distance between sun and moon;d_sm = (1.5 × 10^(11)) - (3.84 × 10^(8)) = 1496.96 × 10^(8) m

Gravitational constant;G = 6.67 × 10^(-11) Nm²/kg²

Now formula for gravitational force between the earth and the moon is;

F_em = (G × M_e × M_m)/(d_em)²

Plugging in relevant values, we have;

F_em = (6.67 × 10^(-11) × 5.98 × 10^(24) × 7.36 × 10^(22))/(3.84 × 10^(8))²

F_em = 1.9909 × 10^(20) N

Similarly, formula for gravitational force between the sun and moon is;

F_sm = (G × M_s × M_m)/(d_sm)²

Plugging in relevant values, we have;

F_se = (6.67 × 10^(-11) × 1.99 × 10^(30) ×

7.36 × 10^(22))/(1496.96 × 10^(8))²

F_se = 4.3595 × 10^(20) N

Thus, net force = F_se - F_em

Net force = (4.3595 × 10^(20) N) - (1.9909 × 10^(20) N) = 2.3686 × 10^(20) N

Answer:

A.

Explanation:

Amplitude measures how much a wave rises or falls. This is illustrated by A.

In the diagram, the amplitude of the wave is shown by A.

There are various definitions of amplitude, which are all functions of the magnitude of the differences between the variable's extreme values.

The amplitude of a variable is simply a measure of change relative to its central position. In contrast, magnitude is a measure of the distance or quantity of a variable irrespective of its direction.

Amplitude is a property that is unique to waves and oscillations.

Therefore, in the diagram, the amplitude of a wave is shown by A.

To learn more about amplitude, refer:

https://brainly.com/question/3613222

#SPJ2

Complete Question

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W = 1 J/s)? Assume each fission reaction releases 200 MeV of energy.

Answer

a. Approximately [tex]5*10^{10}[/tex] fissions per second.

b. Approximately [tex]6*10^{12 }[/tex]fissions per second.

c. Approximately [tex]4*10^{11}[/tex] fissions per second.

d. Approximately [tex]3*10^{12}[/tex] fissions per second.

e. Approximately[tex]3*10^{14}[/tex] fissions per second.

Answer:

The correct option is  d

Explanation:

From the question we are told that

       The energy released by each fission reaction [tex]E = 200 \ MeV = 200 *10^{6} * 1.60 *10^{-19} =3.2*10^{-11} \ J /fission[/tex]

Thus to generated  [tex]100 \ J/s[/tex] i.e  (100 W  ) the rate of fission is  

              [tex]k = \frac{100}{3.2 *10^{-11} }[/tex]

              [tex]k =3*10^{12} fission\ per \ second[/tex]

Answer:

200cm

Explanation:

Answer:

100cm

Explanation:

Using

F= ( N/2L)(√T/u)

F1 will now be (0.5*2)( √600/0.015)

=> L( wavelength)= 200/2cm = 100cm

Answer:

Raw materials are most times gotten from the earth through various forms of extraction procedures.

A) Stainless steel utensils is made up of mainly Iron and other elements such as chromium , carbon etc.

B) Cat litter comprises of ceramic products which is made up of clay.

C) Tums brand antacid tablets comprises of calcium carbonate, magnesium hydroxide, aluminum hydroxide and sodium bicarbonate which could be extracted from the earth.

D)Lithium batteries are made up of elements in the earth such as lithium and carbon.

E)Aluminum beverage cans are made up of aluminum extracted from the ground.

Answer:

Period is 86811.5 seconds.

Explanation:

[tex]{ \boxed{ \bf{T {}^{2} = (\frac{4 {\pi}^{2} }{GM}) {r}^{3} }}}[/tex]

[tex]{ \tt{T {}^{2} = \frac{4 {(3.14)}^{2} }{(6.6 \times {10}^{ - 11} ) \times (5.98 \times {10}^{24} )} \times {((35880\times {10}^{3}) } + (6370 \times {10}^{3} )) {}^{3} }} \\ \\ { \tt{T {}^{2} = 7.54 \times {10}^{9} }} \\ { \tt{T = \sqrt{7.54 \times {10}^{9} } }} \\ { \tt{T = 86811.5 \: seconds}}[/tex]

Complete question is;

A circuit consists of four 100-W lamps connected in parallel across a 230-V supply. Inadvertently, a voltmeter has been connected in series with the lamps. The resistance of the voltmeter is 1500 Ω and that of the lamps under the conditions stated is six times their value then burning normally. What will be the reading of the voltmeter?

Answer:

150.42 V

Explanation:

We are told that the circuit consists of four 100W lamps.

We know that Power is given by the equation;

P = V²/R

Thus;

R = V²/P

Now, we are told that the four lamps are connected in parallel across a 230V supply.

Thus, V = 230 V

So resistance, R = 230²/100

R = 529 Ω

We are told that the resistance of the lamps under the conditions stated is six times their value when burning normally.

Thus, total resistance of each lamp under the conditions = 529 × 6 = 3174 Ω

So, since they are connected in parallel, equivalent resistance for each lamp = 3174/4 = 793.5 Ω

Now, since this resistance is connected in series with the voltmeter resistance of 1500 Ω

Therefore, total circuit resistance = 1500 + 793.5 = 2293.5 Ω

Thus;

circuit current = 230/2293.5 = 0.100283 A

Now, according to Ohm’s law, voltage drop across the voltmeter = 1500 × 0.100283 ≈ 150.42V

CHECK THE COMPLETE QUESTION BELOW

A circuit consists of four 100-W lamps connected in parallel across a 230-V supply. Inadvertently, a voltmeter has been connected in series with the lamps. The resistance of the voltmeter is 1500 Ω and that of the lamps under the conditions stated is six times their value then burning normally. What will be the reading of the voltmeter?

Answer:

the reading of the voltmeter=150.4V

Explanation:

We can determine the wattage of a lamp using below expression:

: W = I² R....................eqn(1)

But fro ohms law V=IR

then I= V/R

If we substitute I into equation (1)

We have W= V²/R

But W= 100W

V= 230V

Then

W=220²/R

100 = 2302/R

R = 529 Ω

We can as well calculate the Resistance of each lamp under given condition that they are sixtimes their value when burning normally.

R = 6 × 529 = 3174 Ω

We can also calculate quivalent resistance of the abovefour lamps connected in parallel then

R = 3174/4

= 793.5 Ω

total circuit resistance can be calculated since we know that resistance is connected to voltmeter of 1500 Ω resistance in series arrangement

Then

total circuit resistance = 1500 + 793.5

= 2293.5 Ω

Then from ohms law again

I= V/R

circuit current = 230/2293.5 A

The reading of the voltage drop across the voltmeter

= 1500 × 230/2293.5

= 150.4V

CHECK COMPLETE QUESTION BELOW

you weigh 685 NN on the earth, what would be your weight on the surface of a neutron star that has the same mass as our sun and a diameter of 25.0 kmkm ? Take the mass of the sun to be msmsm_s = 1.99×1030 kgkg , the gravitational constant to be GGG = 6.67×10−11 N⋅m2/kg2N⋅m2/kg2 , and the free-fall acceleration at the earth's surface to be ggg = 9.8 m/s2m/s2 .

Answer:

5.94×10^15N

Explanation:

the weight on the surface of a neutron star can be calculated by below expresion

W= Mg

W= weight of the person

m= mass of the person

g=gravity of the neutron star

But we need the mass which can be calculated as

m= W/g

m= 685/9.81

m= 69.83kg

From the gravitational law equation we have

F= GMm/r^2

G= gravitational constant = 6.67x10⁻¹¹

M= mass of the neutron star = 1.99x10³⁰ kg

r = distance between the person and the surface

Then r can be calculated as = 25/2 = 12.5 km , we divide by two because it's the distance between the person and the surface

g=gravity of the neutron star can be calculated as

g=(6.67×10^-11 ×1.99×10^30)/(12.5×10^3)^2

= 8.50×10^13m/s^2

Then from W= mg we can find our weight

W= 8.50×10^13m/s^2 × 69.83

= 5.94×10^15N

Therefore, weight on the surface of a neutron star is 5.94×10^15N

Answer:

The correct option is  d

Explanation:

From the question we are told that

     The  electric potential is  [tex]V = 3000 \ V[/tex]

      The  power is  [tex]P = 60 \ W[/tex]

      The  charge delivered is  [tex]q = 3nC = 3.0 *10^{-9} \ C[/tex]

Generally the power generated is mathematically represented as

         [tex]P = I V[/tex]

=>      [tex]I = \frac{P}{V }[/tex]

=>       [tex]I = \frac{60 }{3000 }[/tex]

=>     [tex]I = 0.02 \ A[/tex]

This  current flow is mathematically represented as

           [tex]I = \frac{q -q_o}{\Delta t }[/tex]

Where [tex]q_o[/tex] is the charge delivered at t=0 s which is 0s

     So

             [tex]0.02 = \frac{ (3.0 *10^{-9}) -0 }{t - 0 }[/tex]

               [tex]t = 1.50 *10^{-7 } \ s[/tex]

               [tex]t = 150 *10^{-9 } \ s[/tex]

Answer:

Everything in the Universe is made up of matter and energy. Matter is anything that has mass and occupies space. ... Energy is the ability to cause change or do work. Some forms of energy include light, heat, chemical, nuclear, electrical energy and mechanical energy.

Explanation:

Answer:

1. A

2. C

3. D

Explanation:

Explanation:

According to Ohms Law :

V = I * R

(A) R (Resistance) = 0.022 / 0.75 = 0.03 Ohms

Also,

[tex]r = \alpha \frac{length}{area} = \alpha \frac{5.8}{3.14 \times 0.001 \times 0.001} [/tex]

(B)

[tex] \alpha(resistivity) = 1.62 \times {10}^{ - 8} [/tex]

Drift speed is missing. It is given as;

1.7 × 10^(-5) m/s

A) R = 0.0293 ohms

B) ρ = 1.589 × 10^(-8)

C) n = 8.8 × 10^(28) electrons

This is about finding, resistance and resistivity.

Length; L = 5.8 m

Diameter; d = 2mm = 0.002 m

Radius; r = d/2 = 0.001 m

Voltage; V = 22 mv = 0.022 V

Current; I = 750 mA = 0.75 A

Area; A = πr² = 0.001²π

Drift speed; v_d = 1.7 × 10^(-5) m/s

R = V/I

R = 0.022/0.75

R = 0.0293 ohms

ρ = RA/L

ρ = (0.0293 × 0.001²π)/5.8

ρ = 1.589 × 10^(-8)

J = n•e•v_d

Where;

J = I/A = 0.75/0.001²π A/m² = 238732.44 A/m²

e is charge on an electron = 1.6 × 10^(-19) C

v_d = 1.7 × 10^(-5) m/s

n is number of free electrons per unit volume

Thus;

238732.44 = n(1.6 × 10^(-19) × 1.7 × 10^(-5))

238732.44 = (2.72 × 10^(-24))n

n = 238732.44/(2.72 × 10^(-24))

n = 8.8 × 10^(28)

Read more at; brainly.com/question/17005119

Answer:

The charge is  [tex]q = 1.50 *10^{-5} \ C[/tex]

Explanation:

From the question we are told that

   The electric field strength is  [tex]E = 1860 \ N/C[/tex]

    The force is  [tex]F = 0.02796 \ N[/tex]

Generally the charge on this particle is mathematically represented as

     [tex]q = \frac{F}{E}[/tex]

=>   [tex]q = \frac{0.02796}{ 1860}[/tex]

=>   [tex]q = 1.50 *10^{-5} \ C[/tex]

Answer:

The radius of the black hole will be 2949.6 m.

Explanation:

The radius of this black hole will be the Schwarzschild radius of the mass of the sun

[tex]r_{s}[/tex] = [tex]\frac{2GM}{c^{2} }[/tex]

where

G is the gravitational constant = 6.67 x 10^-11 m^3⋅kg^-1⋅s^-2

M is the mass of the sun = 1.99×10^30 kg

c is the speed of light = 3 x 10^8 m/s

substituting values into the equation, we have

[tex]r_{s}[/tex] = [tex]\frac{2*6.67*10^{-11}*1.99*10^{30} }{(3*10^{8} )^{2} }[/tex] = 2949.6 m

Answer:

His angular velocity will increase.

Explanation:

According to the conservation of rotational momentum, the initial angular momentum of a system must be equal to the final angular momentum of the system.

The angular momentum of a system = [tex]I[/tex]'ω'

where

[tex]I[/tex]' is the initial rotational inertia

ω' is the initial angular velocity

the rotational inertia = [tex]mr'^{2}[/tex]

where m is the mass of the system

and r' is the initial radius of rotation

Note that the professor does not change his position about the axis of rotation, so we are working relative to the dumbbells.

we can see that with the mass of the dumbbells remaining constant, if we reduce the radius of rotation of the dumbbells to r, the rotational inertia will reduce to [tex]I[/tex].

From

[tex]I[/tex]'ω' = [tex]I[/tex]ω

since [tex]I[/tex] is now reduced, ω will be greater than ω'

therefore, the angular velocity increases.

Answer:

Explanation:

For image formation in objective lens

object distance u = 14 +1 = 15 mm

focal length f = 14 mm .

image distance v = ?

lens formula

[tex]\frac{1}{v} -\frac{1}{u} =\frac{1}{f}[/tex]

Putting the values

[tex]\frac{1}{v} +\frac{1}{15} =\frac{1}{14}[/tex]

v = 210 mm .

B )

magnification = v / u

= 210 / 15

= 14

size of image = 14 x 1.1 mm

= 15.4 mm

= 15 mm approx

C )

For final image to be at infinity , image produced by objective lens must fall at the focal point of eye piece . so objective lens's distance from the image formed by objective must be equal to focal length of eye piece that is 21 mm .

21 mm is the answer .

D )

overall magnification =

[tex]\frac{210}{15} \times \frac{D}{f_e}[/tex]

D = 25 cm , f_e = focal length of eye piece

= 14 x 250 / 21

= 166.67

= 170 ( in two significant figures )

(a) The distance of the image v=220mm

(b) SIze of the image 15 mm

(c) Distance of lens be from the image produced by the objective lens 21 mm

(d) overall magnification of the microscope 170

The objective lens of a microscope is the one at the bottom near the sample. At its simplest, it is a very high-powered magnifying glass, with very short focal length. This is brought very close to the specimen being examined so that the light from the specimen comes to a focus inside the microscope tube

For image formation in objective lens

object distance u = 14 +1 = 15 mm

focal length f = 14 mm .

image distance v = ?

By using lens formula

[tex]\dfrac{1}{v}+\dfrac{1}{u}=\dfrac{1}{f}[/tex]

Putting the values

[tex]\dfrac{1}{v}+\dfrac{1}{15}=\dfrac{1}{14}[/tex]

v = 210 mm .

B ) Magnification is the ratio of the size of the image to the size of the an object.

[tex]\rm magnification = \dfrac{v} { u}[/tex]

[tex]M= \dfrac{210} { 15}[/tex]

M= 14

size of image = 14 x 1.1 mm

= 15.4 mm

= 15 mm approx

C )

For final image to be at infinity , image produced by objective lens must fall at the focal point of eye piece . so objective lens's distance from the image formed by objective must be equal to focal length of eye piece that is 21 mm .

21 mm is the answer .

D )

overall magnification =

[tex]\dfrac{210}{15}\times \dfrac{D}{f_e}[/tex]

D = 25 cm , f_e = focal length of eye piece

[tex]= 14 \times \dfrac{ 250} { 21}[/tex]

= 166.67

= 170 ( in two significant figures )

Hence all the answers are:

(a) The distance of the image v=220mm

(b) SIze of the image 15 mm

(c) Distance of lens be from the image produced by the objective lens 21 mm

(d) overall magnification of the microscope 170

To know more about Objective lens follow

https://brainly.com/question/25779311