Answer:
The self-inductance in henries for the solenoid is 0.0274 H.
Explanation:
Given;
number of turns, N = 1500 turns
length of the solenoid, L = 13 cm = 0.13 m
radius of the wire, r = 2 cm = 0.02 m
The self-inductance in henries for a solenoid is given by;
[tex]L = \frac{\mu_oN^2A}{l}[/tex]
where;
[tex]\mu_o[/tex] is permeability of free space = [tex]4\pi*10^{-7} \ H/m[/tex]
A is the area of the solenoid = πr² = π(0.02)² = 0.00126 m²
[tex]L = \frac{4\pi *10^{-7}(1500)^2*(0.00126)}{0.13} \\\\L = 0.0274 \ H[/tex]
Therefore, the self-inductance in henries for the solenoid is 0.0274 H.
a ball is kicked on level ground with a speed of 30 m/s at angle of 40 degrees above horizontal g Find the minimum velocity of the ball during its flight
Answer:
The minimum velocity of the ball during its flight is 22.98 m/s.
Explanation:
The velocity of the ball v = 30 m/s
The angle it makes with the horizontal ∅ = 40°
The minimum velocity of the ball during flight will be the horizontal axis component of the velocity, as acceleration is zero on this axis.
[tex]V_{x}[/tex] = v cos ∅
[tex]V_{x}[/tex] = 30 cos 40°
[tex]V_{x}[/tex] = 30 x 0.766 = 22.98 m/s
How much work is needed to pump all the water out of a cylindrical tank with a height of 10 m and a radius of 5 m
Answer:
Explanation:
volume of water being lifted
= π r² h , where r is radius of cylinder and h is height of cylinder
= 3.14 x5² x 10
= 785 m³
mass of water = 785 x 10³ kg
mass of this much of water is lifted so that its centre of mass is lifted by height
10 / 2 = 5m .
So work done = mgh , m is mass of water , h is displacement of centre of mass and g is acceleration due to gravity
= 785 x 10³ x 9.8 x 5
= 38.465 x 10⁶ J
During the spin cycle of your clothes washer, the tub rotates at a steady angular velocity of 31.7 rad/s. Find the angular displacement Δθ of the tub during a spin of 98.3 s, expressed both in radians and in revolutions.
Answer:
[tex]\Delta \theta = 3116.11\,rad[/tex] and [tex]\Delta \theta = 495.944\,rev[/tex]
Explanation:
The tub rotates at constant speed and the kinematic formula to describe the change in angular displacement ([tex]\Delta \theta[/tex]), measured in radians, is:
[tex]\Delta \theta = \omega \cdot \Delta t[/tex]
Where:
[tex]\omega[/tex] - Steady angular speed, measured in radians per second.
[tex]\Delta t[/tex] - Time, measured in seconds.
If [tex]\omega = 31.7\,\frac{rad}{s}[/tex] and [tex]\Delta t = 98.3\,s[/tex], then:
[tex]\Delta \theta = \left(31.7\,\frac{rad}{s} \right)\cdot (98.3\,s)[/tex]
[tex]\Delta \theta = 3116.11\,rad[/tex]
The change in angular displacement, measured in revolutions, is given by the following expression:
[tex]\Delta \theta = (3116.11\,rad)\cdot \left(\frac{1}{2\pi} \frac{rev}{rad} \right)[/tex]
[tex]\Delta \theta = 495.944\,rev[/tex]
Water is pumped with a 120 kPa compressor entering the lower pipe (1) and flows upward at a speed of 1 m/s. Acceleration due to gravity is 10 m/s and water density is1000 kg/m-3. What is the water pressure on the upper pipe (II).
Answer:
The water pressure on the upper pipe is 92.5 kPa.
Explanation:
Given that,
Pressure in lower pipe= 120 kPa
Speed of water in lower pipe= 1 m/s
Acceleration due to gravity = 10 m/s²
Density of water = 1000 kg/m³
Radius of lower pipe = 12 m
Radius of uppes pipe = 6 m
Height of upper pipe = 2 m
We need to calculate the velocity in upper pipe
Using continuity equation
[tex]A_{1}v_{1}=A_{2}v_{1}[/tex]
[tex]\pi r_{1}^2\times v_{1}=\pi r_{2}^2\times v_{2}[/tex]
[tex]v_{2}=\dfrac{r_{1}^2\times v_{1}}{r_{2}^2}[/tex]
Put the value into the formula
[tex]v_{2}=\dfrac{12^2\times1}{6^2}[/tex]
[tex]v_{2}=4\ m/s[/tex]
We need to calculate the water pressure on the upper pipe
Using bernoulli equation
[tex]P_{1}+\dfrac{1}{2}\rho v_{1}^2+\rho gh_{1}=P_{2}+\dfrac{1}{2}\rho v_{2}^2+\rho gh_{2}[/tex]
Put the value into the formula
[tex]120\times10^{3}+\dfrac{1}{2}\times1000\times1^2+1000\times10\times0=P_{2}+\dfrac{1}{2}\times1000\times(4)^2+1000\times10\times2[/tex]
[tex]120500=P_{2}+28000[/tex]
[tex]P_{2}=120500-28000[/tex]
[tex]P_{2}=92500\ Pa[/tex]
[tex]P_{2}=92.5\ kPa[/tex]
Hence, The water pressure on the upper pipe is 92.5 kPa.
Kepler's laws, satellites motion and weightlessness
Answer:
First Kepler law states that Each planet describes an ellipsoidal motion about the sun as its single focus.
Second Kepler law states that An imaginary line joining a planet to the Sun sweeps out equal areas in equal time intervals.
Third Kepler law states that The squares of period of revolution of the planet around the sun are proportional to the cubes of mean distance between the planet and the sun.
Weightlessness is the condition where the body has zero gravity ( its acceleration is equal to the acceleration due to gravity )
[tex].[/tex]
Kepler's law states that the Sun serves as the planet's center of gravity while they travel in elliptical orbits.
What is the Kepler's motion?Each planet describes an ellipsoidal motion around the sun as its sole focus, according to the first Kepler law.
According to the second Kepler law, an imaginary line between a planet and the Sun sweeps out equivalent areas at equivalent times.
According to the third Kepler law, the squares of a planet's period of revolution around the sun are proportional to the cubes of the planet's mean distance from the sun.
When the body is weightless, there is no gravitational pull on it ( its acceleration is equal to the acceleration due to gravity).
Therefore, the Sun serves as the planet's center of gravity while they travel in elliptical orbits, which is described by Kepler's law.
To learn more about Kepler's motion, refer to the link:
https://brainly.com/question/1608361
#SPJ2
At the pizza party you and two friends decide to go to Mexico City from El Paso, TX where y'all live. You volunteer your car if everyone chips in for gas. Someone asks how much the gas will cost per person on a round trip. Your first step is to call your smarter brother to see if he'll figure it out for you. Naturally he's too busy to bother, but he does tell you that it is 2015 km to Mexico City, there's 11 cents to the peso, and gas costs 5.8 pesos per liter in Mexico. You know your car gets 21 miles to the gallon, but we still don't have a clue as to how much the trip is going to cost (in dollars) each person in gas ($/person).
Answer:
cost_cost = $ 96
Explanation:
In this exercise we have units in the groin system and the SI system, to avoid problems let's reduce everything to the SI system
performance = 21 miles / gallon (1,609 km / 1 mile) (1 gallon / 3,785 l)
perfomance= 8,927 km / l
now let's use a direct rule of proportions (rule of three). If a liter travels 8,927 km, how many liters are needed to travel the 2015 km
#_gasoline = 2015 km (1l / 8.927 km) = 225.72 liters
Now let's find the total cost of fuel. Ns indicates that $ 0.11 = 1 peso and the liter of fuel costs 5.8 pesos
cost_litre = 5.8 peso ($ 0.11 / 1 peso) = $ 0.638
cost_gasoline = #_gasoline cost_litro
cost_gasoline = 225.72 0.638
cost_gasoline = $ 144
This cost is for the one way trip, the total round trip cost is
cost_total = 2 cost_gasoline
cost_total = $ 288
Now let's look for the cost in the vehicle, you and two people will go, for which a total of 3 people will go, so the cost per person is
cost_person = total_cost / #_people
cost_person = 288/3
cost_cost = $ 96
If an electromagnetic wave has components Ey = E0 sin(kx - ωt) and Bz = B0 sin(kx - ωt), in what direction is it traveling?
Answer:
Its traveling in the +x direction
Explanation:
The E-field is in the +y-direction, and the B-field is in the +z-direction, so it must be moving along the +x-direction, since the E-field, B-field and the direction of moving are all at right angles to each other.
The electromagnetic wave is travelling in the +x direction.
Electromagnetic waves are waves formed as a result of vibrations between an electric field and a magnetic field.
Given that:
Ey = E0 sin(kx - ωt)
Hence the electric field is moving in the +y direction.
Also, Bz = B0 sin(kx - ωt)
Hence the magnetic field is moving in the +z direction
Electric fields and magnetic fields (E and B) in an EM wave are perpendicular to each other and are also perpendicular to the direction of propagation of the wave.
Therefore the direction of the wave is travelling in the +x direction.
Find out more at: https://brainly.com/question/25559554
What is the wavelength of electromagnetic radiation which has a frequency of 3.818 x 10^14 Hz?
Answer:
7.86×10⁻⁷ m
Explanation:
Using,
v = λf.................. Equation 1
Where v = velocity of electromagnetic wave, λ = wave length, f = frequency.
make λ the subject of the equation
λ = v/f............... Equation 2
Note: All electromagnetic wave have the same speed which is 3×10⁸ m/s.
Given: f = 3.818×10¹⁴ Hz
Constant: v = 3×10⁸ m/s
Substitute these values into equation 2
λ = 3×10⁸/3.818×10¹⁴
λ = 7.86×10⁻⁷ m
Hence the wavelength of the electromagnetic radiation is 7.86×10⁻⁷ m
The wavelength of this electromagnetic radiation is equal to [tex]7.86 \times 10^{-7} \;meters[/tex]
Given the following data:
Frequency = [tex]3.818\times 10^{14}\;Hz[/tex]Scientific data:
Velocity of an electromagnetic radiation = [tex]3 \times 10^8\;m/s[/tex]
To determine the wavelength of this electromagnetic radiation:
Mathematically, the wavelength of an electromagnetic radiation is calculated by using the formula;
[tex]Wavelength = \frac{Speed }{frequency}[/tex]
Substituting the given parameters into the formula, we have;
[tex]Wavelength = \frac{3 \times 10^8}{3.818\times 10^{14}}[/tex]
Wavelength = [tex]7.86 \times 10^{-7} \;meters[/tex]
Read more wavelength on here: https://brainly.com/question/6352445
Consider a wire of a circular cross-section with a radius of R = 3.17 mm. The magnitude of the current density is modeled as J = cr2 = 9.00 ✕ 106 A/m4 r2. What is the current (in A) through the inner section of the wire from the center to r = 0.5R?
Answer:
The current is [tex]I = 8.9 *10^{-5} \ A[/tex]
Explanation:
From the question we are told that
The radius is [tex]r = 3.17 \ mm = 3.17 *10^{-3} \ m[/tex]
The current density is [tex]J = c\cdot r^2 = 9.00*10^{6} \ A/m^4 \cdot r^2[/tex]
The distance we are considering is [tex]r = 0.5 R = 0.001585[/tex]
Generally current density is mathematically represented as
[tex]J = \frac{I}{A }[/tex]
Where A is the cross-sectional area represented as
[tex]A = \pi r^2[/tex]
=> [tex]J = \frac{I}{\pi r^2 }[/tex]
=> [tex]I = J * (\pi r^2 )[/tex]
Now the change in current per unit length is mathematically evaluated as
[tex]dI = 2 J * \pi r dr[/tex]
Now to obtain the current (in A) through the inner section of the wire from the center to r = 0.5R we integrate dI from the 0 (center) to point 0.5R as follows
[tex]I = 2\pi \int\limits^{0.5 R}_{0} {( 9.0*10^6A/m^4) * r^2 * r} \, dr[/tex]
[tex]I = 2\pi * 9.0*10^{6} \int\limits^{0.001585}_{0} {r^3} \, dr[/tex]
[tex]I = 2\pi *(9.0*10^{6}) [\frac{r^4}{4} ] | \left 0.001585} \atop 0}} \right.[/tex]
[tex]I = 2\pi *(9.0*10^{6}) [ \frac{0.001585^4}{4} ][/tex]
substituting values
[tex]I = 2 * 3.142 * 9.00 *10^6 * [ \frac{0.001585^4}{4} ][/tex]
[tex]I = 8.9 *10^{-5} \ A[/tex]
The four wheels of a car are connected to the car's body by spring assemblies that let the wheels move up and down over bumps and dips in the road. When a 68 kg (about 150 lb) person sits on the left front fender of a small car, this corner of the car dips by about 1.2 cm (about 1/2 in).
If we treat the spring assembly as a single spring, what is the approximate spring constant?
k= ____________
Answer:
The approximate spring constant is [tex]k = 55533.33 \ N/m[/tex]
Explanation:
From the question we are told that
The mass of the person is [tex]m = 68 \ kg[/tex]
The dip of the car is [tex]x = 1.2 \ cm = 0.012 \ m[/tex]
Generally according to hooks law
[tex]F = k * x[/tex]
here the force F is the weight of the person which is mathematically represented as
[tex]F = m * g[/tex]
=> [tex]m * g = k * x[/tex]
=> [tex]k = \frac{m * g }{x }[/tex]
=> [tex]k = \frac{68 * 9.8}{ 0.012}[/tex]
=> [tex]k = 55533.33 \ N/m[/tex]
zeugen and yardang differences
Answer:
Yardangs are formed on vertical strata while zeugen on horizontal strata. ... Yardangs are formed on vertical hard/soft layers of rock, while zeugen (this is its plural form) are formed on horizontal bands of hard/soft rocks giving it a more mushroom-like shape. The Great Sphinx of Giza has been sculpted in a yardang
Can a person break a wall with a punch?(I mean technically,maybe with inhuman speed)
Answer:
yes, shaolin monks can do. you can find tutorials on Youtb
Metal 1 has a larger work function than metal 2. Both are illuminated with the same short-wavelength ultraviolet light.
Do electrons from metal 1 have a higher speed, a lower speed, or the same speed as electrons from metal 2? Explain.
Answer:
a lower speed
Explanation:
Let us look closely at the Einstein's photoelectric equation;
KE= E-Wo
Where;
KE= kinetic energy of the emitted photoelectron
E= energy of the incident photon
Wo= work function of the metal
Hence,where Wo for metal 1 > Wo for metal 2, it follows that KE for metal 1 must also be less than KE for metal 2.
This is because the difference between E and Wo for metal 1 is smaller than the same difference for metal 2 hence the answer.
Now the friends are ready to tackle a homework problem. A pulse is sent traveling along a rope under a tension of 29 N whose mass per unit length abruptly changes, from 19 kg/m to 45 kg/m. The length of the rope is 2.5 m for the first section and 2.8 m for the second, and the second rope is rigidly fixed to a wall. Two pulses will eventually be detected at the origin: the pulse that was reflected from the medium discontinuity and the pulse that was originally transmitted, which hits the wall and is reflected back and transmitted through the first rope. What is the time difference, Δt, between the two pulses detected at the origin? s
Answer:
The time difference is 2.97 sec.
Explanation:
Given that,
Tension = 29 N
Mass per unit length [tex]\mu_{1}=19\ kg/m[/tex]
Mass per unit length [tex]\mu_{2}=45\ kg/m[/tex]
Length of first section = 2.5 m
Length of second section = 2.8 m
We need to total distance of first pulse
Using formula for distance
[tex]d=2.5+2.5[/tex]
[tex]d_{1}=5.0\ m[/tex]
We need to total distance of second pulse
Using formula for distance
[tex]d=2.8+2.8[/tex]
[tex]d_{2}=5.6\ m[/tex]
We need to calculate the speed of pulse in the first string
Using formula of speed
[tex]v_{1}=\sqrt{\dfrac{T}{\mu_{1}}}[/tex]
Put the value into the formula
[tex]v_{1}=\sqrt{\dfrac{29}{19}}[/tex]
[tex]v_{1}=1.24\ m/s[/tex]
We need to calculate the speed of pulse in the second string
Using formula of speed
[tex]v_{2}=\sqrt{\dfrac{T}}{\mu_{2}}}[/tex]
Put the value into the formula
[tex]v_{2}=\sqrt{\dfrac{29}{45}}[/tex]
[tex]v_{2}=0.80\ m/s[/tex]
We need to calculate the time for first pulse
Using formula of time
[tex]t_{1}=\dfrac{d_{1}}{v_{1}}[/tex]
Put the value into the formula
[tex]t_{1}=\dfrac{5.0}{1.24}[/tex]
[tex]t_{1}=4.03\ sec[/tex]
We need to calculate the time for second pulse
Using formula of time
[tex]t_{2}=\dfrac{d_{1}}{v_{1}}[/tex]
Put the value into the formula
[tex]t_{2}=\dfrac{5.6}{0.80}[/tex]
[tex]t_{2}=7\ sec[/tex]
We need to calculate the time difference
Using formula of time difference
[tex]\Delta t=t_{2}-t_{1}[/tex]
Put the value into the formula
[tex]\Delta t=7-4.03[/tex]
[tex]\Delta t=2.97\ sec[/tex]
Hence, The time difference is 2.97 sec.
The starter motor of a car engine draws a current of 140 A from the battery. The copper wire to the motor is 4.20 mm in diameter and 1.2 m long. The starter motor runs for 0.760 s until the car engine starts.Required:a. How much charge passes through the starter motor? b. How far does an electron travel along the wire while the starter motor is on?(mm)
Answer:
(a)106.4C
b)0.5676mm
Explanation:
(a)To get the charge that have passed through the starter then The current will be multiplied by the duration
I= current
t= time taken
Q= required charge
Q= I*t = 140*0.760 = 106.C
(b) b. How far does an electron travel along the wire while the starter motor is on?(mm)
diameter of the conductor is 4.20 mm
But Radius= diameter/2= 4.20/2=
The radius of the conductor is 2.1mm, then if we convert to metre for consistency same then
radius of the conductor is 0.0021m.
We can now calculate the area of the conductor which is
A = π*r^2
= π*(0.0021)^2 = 13.85*10^-6 m^2
We can proceed to calculate the current density below
J = 140/13.85*10^-6 = 10108303A/m
According to the listed reference:
Where e= 1.6*10^-19
n= 8.46*10^28
Vd = J/(n*e) = 10108303/ ( 8.46*10^28 * 1.6*10^-19 ) =0.0007468m/s=0 .7468 mm/s
Therefore , the distance traveled is:
x = v*t = 0.7468 * 0.760 = 0.5676mm
(a) The charge passes through the starter motor is 106.4C.
(b) An electron travel along the wire while the starter motor is on 0.5676mm.
ElectronAnswer (a)
I= current
t= time taken
Q= required charge
Q= I*t
Q= 140*0.760
Q= 106.C
Answer (b)
The n electron travel along the wire while the starter motor is on:
Diameter of the conductor is 4.20 mm
Radius= diameter/2= 4.20/2
Radius =2.1mm
Radius of the conductor is 0.0021m.
A = π*r^2
A= π*(0.0021)^2
A= 13.85*10^-6 m^2
Where e= 1.6*10^-19
n= 8.46*10^28
Vd = J/(n*e) = 10108303/ ( 8.46*10^28 * 1.6*10^-19 )
Vd =0.0007468m/s
Vd =0 .7468 mm/s
The distance traveled is:
x = v*t
x= 0.7468 * 0.760
x = 0.5676mm
Learn more about "Electron":
https://brainly.com/question/1255220?referrer=searchResults
In a two-slit experiment, the slit separation is 3.34 ⋅ 10 − 5 m. The interference pattern is created on a screen that is 3.30 m away from the slits. If the 7th bright fringe on the screen is 29.0 cm away from the central fringe, what is the wavelength of the light?
Answer:
The wavelength is [tex]\lambda = 419 \ nm[/tex]
Explanation:
From the question we are told that
The distance of separation is [tex]d = 3.34 *10^{-5} \ m[/tex]
The distance of the screen is [tex]D = 3.30 \ m[/tex]
The order of the fringe is n = 7
The distance of separation of fringes is y = 29.0 cm = 0.29 m
Generally the wavelength of the light is mathematically represented as
[tex]\lambda = \frac{y * d }{ n * D}[/tex]
substituting values
[tex]\lambda = \frac{0.29 * 3.34*10^{-5} }{ 7 * 3.30}[/tex]
[tex]\lambda = 4.19*10^{-7}\ m[/tex]
[tex]\lambda = 419 \ nm[/tex]
An electron in the first energy level of the electron cloud has an electron in the third energy level
Answer:
a lower energy than
Explanation:
sorry im a month late but is lower energy than
1. What was the Michelson-Morley experiment designed to do?2. When was the Michelson-Morley experiment done?3. What was the ether?4. What does the speed of a wave depend on?5. How many light beams are used in Michelson’s interferometer?6. What sort of problems did Michelson have with his first interferometer?7. How many times more sensitive was Michelson’s second interferometer?8. What did the new interferometer float on?9. What was the surprising outcome of the Michelson-Morley experiment?10. What were the implications of the experiment?11. What is the principle behind relativity?12. Who became the first American to win the Nobel Prize?13. Did Einstein base his Theory of Relativity on the Michelson-Morley experiment?
Answer:
1) designed to measure the difference in speed of light in different directions , 1887
Explanation:
1) This experiment was designed to measure the difference in speed of light in different directions and therefore find the speed of the ether.
2) was made in 1887
3) At that time it was assumed that it was the medium in which light traveled and it is everywhere
4) the speed of the wave depends on the characteristics of the medium where it travels,
for the one in a string depends on the tension and density
for an electromagnetic wave of the permittivity and permeability of the vacuum
5) In this type of interferometer the beam is divided into two rays
6) In his interrupter, he had to accurately measure the displacement of the fringes in a telescope, for which he had to minimize vibrations, he had problems in the movement of one of the arms, changes in temperature
7) In Michelsom's second experiment, the apparatus could measure 0.01 fringes by increasing the length of the arms by 11 m
8) The new interferometer floated on a bed of mercury
9) Couldn't measure any difference in speed of light in different directions
10) Physics was forced to eliminate the concept of ETHER
11) One of the principles of relativities that the speed of light is constant in all inertial efficiency systems
12) Michelson in 1907
13) It seems that Einstein did not know the results of this experiment
A rod on a compressed spring exerts 12 N of force on a 0.05-kg steel ball. The
rod pushes the ball 0.03 m. How much work does the spring do on the ball?
A) 36
B) 36 N
C) 60 N
D)1.00
Answer:
Work = 0.36N
Explanation:
Given
Force = 12N
Distance = 0.03m
Weight = 0.05kg
Required
Determine the work done
Workdone is calculated as thus;
Work = Force * Distance
Substitute 12N for Force and 0.03m for Distance
Work = 12N * 0.03m
Work = 0.36Nm
Using proper S.I units
Work = 0.36N
Hence, work done by the spring on the ball is 0.36N
A car accelerates uniformly from rest and reaches a speed of 22.7 m/s in 9.02 s. Assume the diameter of a tire is 58.5 cm. (a) Find the number of revolutions the tire makes during this motion, assuming that no slipping occurs. rev (b) What is the final angular speed of a tire in revolutions per second? rev/s
(a) The car is undergoing an acceleration of
[tex]a=\dfrac{22.7\frac{\rm m}{\rm s}-0}{9.02\,\mathrm s}\approx2.52\dfrac{\rm m}{\mathrm s^2}[/tex]
so that in 9.02 s, it will have covered a distance of
[tex]x=\dfrac a2(9.02\,\mathrm s)^2\approx102\,\mathrm m[/tex]
The car has tires with diameter d = 58.5 cm = 0.585 m, and hence circumference π d ≈ 1.84 m. Divide the distance traveled by the tire circumference to determine how many revolutions it makes:
[tex]\dfrac{102\,\mathrm m}{1.84\,\mathrm m}\approx55.7\,\mathrm{rev}[/tex]
(b) The wheels have average angular velocity
[tex]\omega=\dfrac{\omega_f+\omega_i}2=\dfrac{\theta_f-\theta_i}{\Delta t}[/tex]
where [tex]\omega[/tex] is the average angular velocity, [tex]\omega_i[/tex] and [tex]\omega_f[/tex] are the initial and final angular velocities (rev/s), [tex]\theta_i[/tex] and [tex]\theta_f[/tex] are the initial and final angular displacements (rev), respectively, and [tex]\Delta t[/tex] is the duration of the time between initial and final measurements. The second equality holds because acceleration is constant.
The wheels start at rest, so
[tex]\dfrac{\omega_f}2=\dfrac{55.7\,\rm rev}{9.02\,\rm s}\implies\omega_f\approx12.4\dfrac{\rm rev}{\rm s}[/tex]
A tuning fork with a frequency of 335 Hz and a tuning fork of unknown frequency produce beats with a frequency of 5.3 when struck at the same time. A small piece of putty is placed on the tuning fork with the known frequency and it's frequency is lowered slightly. When struck at the same time, the two forks now produce a beat frequency of 8 Hz. 1)What is frequency of tuning fork which originally had a frequency of 335 Hz after the putty has been placed on it
Answer:
Explanation:
Unknown fork frequency is either
335 + 5.3 = 340.3 Hz
or
335 - 5.3 = 329.7 Hz
After we modify the known fork, the unknown fork frequency equation becomes either
(335 - x) + 8 = 340.3
(335 - x) = 332.3
x = 2.7 Hz
or
(335 - x) + 8 = 329.7
(335 - x) = 321.7
x = 13.3 Hz
IF the unknown fork frequency was 340.3 Hz,
THEN the 335 Hz fork was detuned to 335 - 2.7 = 332.3 Hz
IF the unknown fork frequency was 329.7 Hz,
THEN the 335 Hz fork was detuned to 335 - 13.3 = 321.7 Hz
A 80 kg bungee jumper is on a bridge that is 100 meters above a river. Attached to the jumper is a bungee cord that is 50 meters long. After jumping off of the bridge, the jumper reaches a position that is 10 meters above the river when the bungee cord is at its maximum stretch.
Required:
a. How much energy is stored in the bungee cord at that maximum stretch?
b. What is the spring force constant of the bungee cord?
Answer:
a) 70,560 J
b) 88.2 N/m
Explanation:
The spring potential will equal the change in gravity potential
PS = PE = mgh = 80(9.8)(100 - 10) = 70,560 J
PS = ½kx²
k = 2PS/x² = 2(70560)/(100 - 50 - 10)² = 88.2 N/m
Matter's resistance to a change in motion is called
Answer:
Inertia! I hope this helps!
Answer:
inertia
Explanation
Inertia.
pls try to understand my doubt and clear it
.
A defibrillator is a device used to shock the heart back to normal beat patterns. To do this, it discharges a 15 μF capacitor through paddles placed on the skin, causing charge to flow through the heart. Assume that the capacitor is originally charged with 5.0 kV .Part AWhat is the charge initially stored on the capacitor?3×10−9 C7.5×104 C7.5×10−2 C7.5×10−5 CPart BWhat is the energy stored on the capacitor?What is the energy stored on the capacitor?1.9×108 J380 J190 J1.9×10−4 JPart CIf the resistance between the two paddles is 100 Ω when the paddles are placed on the skin of the patient, how much current ideally flows through the patient when the capacitor starts to discharge?5×105 A50 A2×10−2 A5×10−2 APart DIf a defibrillator passes 17 A of current through a person in 90 μs . During this time, how much charge moves through the patient?If a defibrillator passes 17 {\rm A} of current through a person in 90 {\rm \mu s} . During this time, how much charge moves through the patient?190 mC1.5 C1.5 mC17 C
Answer:
a) q = 7.5 10⁻² C , b) 190 J , c) I₀ = 50 A , d) 1.5 mC
Explanation:
The expression for capacitance is
C = q / DV
q = C DV
let's reduce the magnitudes to the SI system
ΔV = 5 kV = 5000 V
C = 15 μF = 15 10⁻⁶ F
t = 90 μs = 90 10⁻⁶ s
q = 15 10⁻⁶ 5000
q = 7.5 10⁻² C
b) the energy in a capacitor is
U = ½ C ΔV²
U = ½ 15 10⁻⁶ 5000²
U = 1,875 10² J
answer 190 J
c) At the moment the discharge begins, all the current is available and it decreases with time,
whereby
V = I R
in the first instant I = Io
I₀ = V / R
I₀ = 5000/100
I₀ = 50 A
but this is for a very short time
answer 50 A
d) The definition of current is
i = dq / dt
in this case they give us the total current and the total time, so we can find the total charge
i = q / t
q = i t
q = 17 90 10⁻⁶
q = 1.53 10⁻³ C
answer is 1.5 mC
A stationary coil is in a magnetic field that is changing with time. Does the emf induced in the coil depend
Answer:
Explanation:
The e.m.f induced in the coil depend on the following :
(a) No. of turns in the coil
(b) Cross-sectional Area of the coil
(c) Magnitude of Magnetic field
(d) Angular velocity of the coil
A diffraction grating with 200 lines per mm is used in an experiment to study the visible spectrum of a gas discharge tube. At what angle from the beam axis will the first order peak occur if the tube emits light with wavelength of 617.3 nm
Answer
123.5 x 10 ^-3 radian
Explanation:
Given the Width of slit a = 1 x 10⁻³ / 200
a = 5x 10⁻⁶ m .
angle at which first order peak is formed
= λ / a (where λ is wavelength and a is width of slit)
given λ = 617.3 x 10⁻⁹ m
a = 5 x 10⁻⁶
θ = 617.3 x 10⁻⁹ / 5 x 10⁻⁶
= 123.5x 10⁻³ radian .
first order peak is formed at an angle of 123.5 x 10⁻³ radian .
Explanation:
1 hallar el trabajo mecanico de un cuerpo que tiene una fuerza de 250 newton y recorre 750 metros
2 hallar la potencia necesaria para levantar un transformador de masa 2500kg,una altura de 4 metros en un tiempo de 30 segundos
porfa es para hoy
Answer: TRACK
Explanation:
A fish is 11.9 cm from the front surface of a fish bowl of radius 33 cm. Where does the fish appear to be to someone in air viewing it from in front of the bowl
Answer:
The fish would appear 42.7 cm on the left side from the front of the bowl.
Explanation:
The fish (object) distance = 11.9 cm, radius of curvature of the bowl = 33 cm. The distance of image of the fish (image distance) can be determined by applying the mirror formula;
[tex]\frac{1}{f}[/tex] = [tex]\frac{1}{u}[/tex] + [tex]\frac{1}{v}[/tex]
where f is the focal length of the reflecting surface, u is the object distance and v is the image distance.
But, f = [tex]\frac{radius of curvature}{2}[/tex]
= [tex]\frac{33}{2}[/tex]
f = 16.5 cm
Substitute f = 16.5 = [tex]\frac{165}{10}[/tex], and u = 11.9 = [tex]\frac{119}{10}[/tex] in equation 1;
[tex]\frac{10}{165}[/tex] = [tex]\frac{10}{119}[/tex] + [tex]\frac{1}{v}[/tex]
[tex]\frac{1}{v}[/tex] = [tex]\frac{10}{165}[/tex] - [tex]\frac{10}{119}[/tex]
= [tex]\frac{1190 - 1650}{19635}[/tex]
[tex]\frac{1}{v}[/tex] = [tex]\frac{-460}{19635}[/tex]
⇒ v = [tex]\frac{19635}{-460}[/tex]
= -42.6848
v = 42.7 cm
The fish would appear 42.7 cm on the left side from the front of the bowl.
A train on one track moves in the same direction as a second train on the adjacent track. The first train, which is ahead of the second train and moves with a speed of 36.4 m/s , blows a horn whose frequency is 123 Hz .what is its speed?
Answer:
51. 7m/s
Explanation:
Take speed of sound in air = 340 m/s
fp = fs (V + Vp)/(V + Vs)
128 = 123 (340 + Vp)/(340 + 36.4)
Vp = 51.7m/s
Explanation: