When exchanging information with anyone involved in the collision, you should _____.

Answer:

A) Flow depth = 2.46 m, Froude number after jump = 0.464

B) head loss = 0.572 m

C) dissipation ratio = 0.173

Explanation:

Given data :

Velocity before jump ( v1 ) = 7 m/s

flow depth before jump ( y1 ) = 0.8 m

g = 9.81 m/s

Esi = 3.3 m ( calculated )

attached below is a detailed solution of the problem

Answer:

b. What is the operator's efficiency for the day?

                                                      AND

e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?

Explanation:

Answer:

Explanation:

f = 50.0 Hz, L = 0.650 H, π = 3.14

C = 4.80 μF, R = 301 Ω resistor. V = 120volts

XL = wL = 2πfL

= 2×3.14×50* 0.650

= 204.1 Ohm

Xc= 1/wC

Xc = 1/2πfC

Xc = 1/2×3.14×50×4.80μF

= 1/0.0015072

= 663.48Ohms

1. Total impedance, Z = sqrt (R^2 + (Xc-XL)^2)= √ 301^2+ (663.48Ohms - 204.1 Ohm)^2

√ 90601 + (459.38)^2

√ 90601+211029.98

√ 301630.9844

= 549.209

Z = 549.21Ohms

2. I=V/Z = 120/ 549.21Ohms =0.218Ampere

3. P=V×I = 120* 0.218 = 26.16Watt

Note that

I rms = Vrms/Xc

= 120/663.48Ohms

= 0.18086A

4. I(max) = I(rms) × √2

= 0.18086A × 1.4142

= 0.2557

= 0.256A

5. V=I(max) * XL

= 0.256A ×204.1

=52.2496

= 52.250volts

6. V=I(max) × Xc

= 0.256A × 663.48Ohms

= 169.85volts

7. Xc=XL

1/2πfC = 2πfL

1/2πfC = 2πf× 0.650

1/2×3.14×f×4.80μF = 2×3.14×f×0.650

1/6.28×f×4.8×10^-6 = 4.082f

1/0.000030144× f = 4.082×f

1 = 0.000030144×f×4.082×f

1 = 0.000123f^2

f^2 = 1/0.000123048

f^2 = 8126.922

f =√8126.922

f = 90.14 Hz

Answer:

The answers to your questions are given below.

Explanation:

The following data were obtained from the question:

Red (R) = 4

White (W) = 7

1. Determination of the sample space, S.

The box contains 4 red balls and 7 white balls. Therefore, the sample space (S) can be written as follow:

S = {R, R, R, R, W, W, W, W, W, W, W}

nS = 11

2. Determination of the probability of all results that appeared in the sample space.

From the question, we were told that the two balls was drawn with return. There, the probability of all results that appeared in the sample space can be given as follow:

i. Probability that the first draw is red and the second is also red.

P(R1) = nR/nS

Red (R) = 4

Space space (S) = 11

P(R1) = nR/nS

P(R1) = 4/11

P(R2) = nR/nS

P(R2) = 4/11

P(R1R2) = P(R1) x P(R2)

P(R1R2) = 4/11 x 4/11

P(R1R2) = 16/121

Therefore, the Probability that the first draw is red and the second is also red is 16/121.

ii. Probability that the first draw is red and the second is white.

Red (R) = 4

White (W) = 7

Space space (S) = 11

P(R) = nR/nS

P(R) = 4/11

P(W) = nW/nS

P(W) = 7/11

P(RW) = P(R) x P(W)

P(RW) = 4/11 x 7/11

P(RW) = 28/121

Therefore, the probability that the first draw is red and the second is white is 28/121.

iii. Probability that the first draw is white and the second is also white.

White (W) = 7

Space space (S) = 11

P(W1) = nW/nS

P(W1) = 7/11

P(W2) = nW/n/S

P(W2) = 7/11

P(W1W2) = P(W1) x P(W2)

P(W1W2) = 7/11 x 7/11

P(W1W2) = 49/121

Therefore, the probability that the first draw is white and the second is also white is 49/121.

iv. Probability that the first draw is white and the second is red.

Red (R) = 4

White (W) = 7

Space space (S) = 11

P(W) = nW/nS

P(W) = 7/11

P(R) = nR/nS

P(R) = 4/11

P(WR) = P(W) x P(R)

P(WR) = 7/11 x 4/11

P(WR) = 28/121

Therefore, the probability that the first draw is white and the second is red is 28/121.

Answer:

[tex]w_{out}=319.1\frac{BTU}{lbm}[/tex]

Explanation:

Hello,

In this case, for the inlet stream, from the steam table, the specific enthalpy and entropy are:

[tex]h_1=1456.0\frac{BTU}{lbm} \ \ \ s_1=1.6413\frac{BTU}{lbm*R}[/tex]

Next, for the liquid-vapor mixture at the outlet stream we need to compute its quality by taking into account that since the turbine is adiabatic, the entropy remains the same:

[tex]s_2=s_1[/tex]

Thus, the liquid and liquid-vapor entropies are included to compute the quality:

[tex]x_2=\frac{s_2-s_f}{s_{fg}}=\frac{1.6313-0.39213}{1.28448}=0.965[/tex]

Next, we compute the outlet enthalpy by considering the liquid and liquid-vapor enthalpies:

[tex]h_2=h_f+x_2h_f_g=236.14+0.965*933.69=1136.9\frac{BTU}{lbm}[/tex]

Then, by using the first law of thermodynamics, the maximum specific work is computed via:

[tex]h_1=w_{out}+h_2\\\\w_{out}=h_1-h_2=1456.0\frac{BTU}{lbm}-1136.9\frac{BTU}{lbm}\\\\w_{out}=319.1\frac{BTU}{lbm}[/tex]

Best regards.

Answer:

Hello bro

Explanation:

I think i can help you something but can you translate it on english plzz

Answer:

1. A.True

2. B.False

3. B.False

4. A.True

5. A.True

6. A.True

7. A.True

8. B.False

9. B.False

10. A.True

11. B.False

12. A.True

13. A.True

14. B.False

15. B.False

16. A.True

Explanation:

Most steels have endurance and fatigue limit about half the Tensile strength. Tensile strength of material is the limit of stress at which material then breaks. The tensile stress in a bolt is calculated through tensile force.

GIS

The full for GIS is : Geographic Information System.

The GIS is a system of mapping that is used to create, analyze, manage and map all the types of data.

It is a method capturing, checking as well as displaying all the data that is related to the position of the surface of earth.

Remote Sensing

Remote sensing is defined as a process where the various physical characteristics of an area are constantly monitored and detected by a process of measuring the reflection of the emitted radiations at ta distance.

The snow covered areas of the Kabul basin can be monitored and analyzed by using the process of GIS and remote sensing.

They provide a continuous source of information and data about snow covered peaks, the amount of snow to the authorities.

Learn More :

https://brainly.in/question/1556256?__cf_chl_captcha_tk__=pmd_2d2d9994422ca43d3cbbcf6322e6c34da175405a-1628654009-0-gqNtZGzNAvijcnBszQ3i

The amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.

Heat is defined as the process of kinetic energy being transferred from an energy source to a medium or an item. These three mechanisms radiation, conduction, and convection can all transmit energy. These three modes of heat transfer are typically combined, and it often happens on its own. The heat energy can be transformed into other types of energy, such as mechanical and kinetic energy. Thermal (heat) energy is a type of energy that is produced by the movement of particles and is a component of all matter.

The process rejects a certain amount of heat, which is

-q = w + Δu

q = - w - Δu

q = - 185.5 kJ/kg - 1948.9 kJ/kg

q = 2133.4 kJ/kg

Thus, the amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.

To learn more about heat, refer to the link below:

https://brainly.com/question/1429452

#SPJ2

Answer:

True

Explanation:

There are 16 in all and 4 are not mandatory

There are some sections of the SDS that are not mandatory. Thus, option A is correct.

A Safety Data Sheet, previously known as a Material Safety Data Sheet, is a thorough instructional report written by a dangerous product's producer or exporter. It gives a description of something like the product's chemical and physical characteristics.

Sections 1 through 11 and 16 must be used; sections 12 through 15 are optional but could be included. the section which will are not compulsory are:

Section 12: Environmental data

Section 13: Guidelines for Recycling

Section 14: Documentation regarding mobility

Section 15: Relevant data about regulations

In Safety Data Sheet, all the sections are not compulsory or mandatory. this statement is true. Therefore, option A is the correct option.

Learn more about Safety Data Sheet, here:

https://brainly.com/question/1442958

#SPJ2

Answer:

1. Yes, they are all necessary.

2. Both written and verbal communication skills are of the utmost importance in business, especially in engineering. Communication skills boost you or your teams' performance because they provide clear information and expectations to help manage and deliver excellent work.

Answer:

30 feet

Explanation:

Given data :

design speed = 30 miles/h

super elevation = 0.08

determine the width of the turning roadway

calculate the value of R = V^2 / 15( e + p)

e = 0.08 , p = 0.2 , v = 30

R = (30)^2 / 15 ( 0.08 + 0.2 )

  = 900 / 15 ( 0.28 )

  ≈ 215 ft

pavement width from the calculation above = 28 ft

width of the turning roadway = pavement width + 2 = 30 feet ( because there are two vertical widths joining up the main road at the T junction )

Answer:

  Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data.

Explanation:

The only design that has resistance varying with everything else remaining the same is the first design. That would be what you'd want to do if you're exploring the effect of resistance on current.

I inferred you want literal editing of the text above.

Explanation:

Here's a correction of the sentences:

1. The author, an expert in cybersecurity will speak via Zoom on Wednesday.

In this sentence, punctuation mark ( , ) was added and the word  'this' was replaced with 'on'.

2. Williams' book contains many illustrations, which makes it easy to read.

Added punctuation and made a revision of the sentence.

3. Based on the available evidence, the university administrators have opted for a hybrid format for the fall, which begins September 20.

Mainly added punctuations to make the senstence clarer.

4. (Thesis statement) I believe Free laptops should be offered to all students who need them.

Made a few additions.

Answer:

3.983 MW

Explanation:

Given that:

At the inlet:

Velocity (v₁) = 30 m/s

Enthalpy (h₁) = 3348 kJ/kg

At the outlet:

Velocity (v₂) = 60 m/s

Enthalpy (h₂) = 2550 kJ/kg

Mass flow rate (m) = m₁ = m₂ = 5kg/s

According to the steady flow energy equation:

[tex]Q+ m_1 (h_1 + \dfrac{v_1^2}{2000}+ \dfrac{gz_1}{1000} )= m_2(h_2+\dfrac{v_2^2}{2000}+\dfrac{gz_2}{1000})+W_{shaft}[/tex]

Since the elevation (z) is negligible and flow via the turbine is adiabatic:

Then,

Q = 0 and z₁ = z₂

∴

[tex]W_{shaft} = (mh_1-mh_2) + (\dfrac{mv_1^2-mv_2^2}{2000})[/tex]

[tex]W_{shaft} = ((5*3348) -(5*2550)) + (\dfrac{(5*(30)^2)-(5*(60)^2)}{2000})[/tex]

[tex]W_{shaft} = (16740-12750) + (\dfrac{4500-18000}{2000})[/tex]

[tex]W_{shaft} = (16740-12750) + (-6.75)[/tex]

[tex]W_{shaft} = 3983.25 \ kW[/tex]

[tex]\mathbf{W_{shaft} = 3.983 \ MW}[/tex]

Answer:

efficiency

Explanation:

Answer:

The correct answer is Efficiency.

Explanation:

I got it right on the plato test.

Answer:

Um is there suppose to be a picture with the sentences on

Answer:

It's B I did the test and I was right on B

Explanation:

I don't know I knew it was B

Answer:

b. abc

Explanation:

The phase rotation and its sequence is order in which voltage is reached to their respective sources. The wave forms of a polyphase flow through AC source to the panel. The three phase system has two possible sequence which can be a-b-c or c-b-a. The correct answer is therefore b.

Answer:

"Process capability" is the correct answer.

Explanation:

Answer:

b

Explanation:

what is anythin efficiency if ta

Answer:

B) gate-source junction is reverse-biased

Explanation:

FET is described as an electric field that controls the specific current and is being applied to a "third electrode" which is generally known as "gate". However, only the electric field is responsible for controlling the "current flow"   in a specific channel and then the particular device is being "voltage operated" that consists of high "input impedance".

In FET, the different "charge carriers" tend to enter a particular channel via "source" and exits through "drain".

Answer: all of the above

Explanation:

To drive safely in the station, the correct option is D. All of the above.

It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.

One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights

Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.

In conclusion, the correct option is D.

Read related link on:

https://brainly.com/question/18889428

Answer:

the rate of heat loss from the duct to the attic space = 1315.44 W

the pressure difference between the inlet and outlet sections of the duct  = 7.0045 N/m²

Explanation:

We know that properties of air 80⁰C  and 1atm  (from appendix table) are;

density p = 0.9994 kg/m³, Specifice heat Cp = 1008 J/kg.⁰C

Thermal conductivity k = 0.02953 W/m.⁰C, Prandtl number Pr = 0.7154,

Kinematic viscosity v = 2.097 × 10⁻⁵ m²/s

haven gotten that, we calculate the hydraulic diameter of square duct

Dh = 4Ac / P      { Ac = is cross sectional area of duct and P = perimeter}

now we substitute a² for Ac and 4a for P ( we know from the question that a = 0.2 m)

Dh = 4a² / 4a

Dh = 4(0.2)² / 4(0.2)

Dh = 0.2 m

Now we calculate the average velocity of air

Vₐ = Vˣ / Ac        { vˣ = volume flow rate of air}

Vₐ = Vˣ / a²      { Ac = a² }, we know that a = 0.2m₂, Vˣ = 0.15 m³

Vₐ = 0.15 / (0.2)²

Vₐ = 3.75 m/s

Next we calculate the Reynolds number

Re = Vₐ Dh / V

Re = (3.75 × 0.2) / 2.097× 10⁻⁵

Re = 35765.379

The  Reynolds number IS GREATER than 10,000

so the flow is turbulent and entry length in this case is nearly 10 times the hydraulic diameter

Lh ≈ Lt ≈ 10D

= 10 × 0.2

= 2m

As this length is quite small when compared to the total of tube, we assume fully developed flow for the entire tube length.

Now we calculate the Nusselt number from this relation;

Nu =  0.023 Re⁰'⁸ Pr⁰'³

so we substitute for Re and Pr

Nu = 0.023(35765.379)⁰'⁸ (0.7154)⁰'³

Nu = 91.4

Now calculate the convective heat transfer coefficient

h = Nu × K/ Dh

we substitute

h = 91.4 × 0.02953 W/m.°C / 0.2 m

h = 13.5 W/m².°C

We calculate the surface area of the square duct

Aₓ = 4aL       { L= length of duct}

we substitute

Aₓ = 4 × 0.2 × 8

Aₓ = 6.4 m²

Mass flow rate of air

m = pVˣ

we substitute again ( from our initials)

m = 0.9994 kg/m₃ × 0.15 m³/s

m= 0.150 kg/s

We calculate the exit temperature of the air from the duct

Te = Ts - (Ts -Ti) exp ( - hAₓ / mCp)

we know that

Ts = 60°C , Ti = 80°C, h = 13.5 W/m².°C , Aₓ = 6.4m², m = 0.150 kg/s , Cp = 1008 J/kg.°C

we substitute

Te = 60 - (60-80) exp(- ((13.5 × 6.4)/(0.15 × 1008))

Te = 71.3°

Now we calculate the rate of heat loss from the duct.

Q = mCp ( Ti -Te )

we substitute again

Q = 0.150 × 1008 × ( 80 - 71.3 )

Q = 1315.44 W

Next we calculate the estimated friction factors by using Haaland equation

1/√f = - 1.8log₁₀ [ 6.9/Re + (E/D)/3.7)¹'¹¹]

we know that E/D = relative roughness = 10⁻³

we substitute

so

1/√f = - 1.8log₁₀ [ (6.9/35765.379) + ( 10⁻³/3.7)¹'¹¹]

1/√f = - 1.8log₁₀ { 0.000192924 + 0.00010947}

1/√f = - 1.8log₁₀ 0.000302324  

√f =   1/6.334

f = (1/6.334)²

f = 0.02492

We calculate the pressure difference between inlet and outlet sections of the duct

ΔPl = fLPVa² / Dh × 2

ΔPl = {0.02492 × 8 × 0.9994 × (3.75)²} / 0.2 × 2

ΔPl = 2.8018 / 0.4

ΔPl = 7.0045 N/m²

Therefore pressure deference is 7.0045 N/m²

Answer:both

Explanation:

Answer: hello some aspects of your question is missing below is the missing information

The gas tank is made from A-36 steel and has an inner diameter of 1.50 m.

answer:

≈ 22.5 mm

Explanation:

Given data:

Inner diameter = 1.5 m

pressure = 5 MPa

factor of safety = 1.5

Calculate the required minimum wall thickness

maximum-shear-stress theory ( σ allow ) = σγ / FS

                                                  = 250(10)^6 / 1.5  = 166.67 (10^6) Pa

given that |σ| = σ allow  

3.75 (10^6) / t = 166.67 (10^6)

∴ t ( wall thickness ) = 0.0225 m   ≈ 22.5 mm

Answer:

C) Decreases with an increase in temperature

Explanation:

As the temperature of a transistor increases, the thermal runaway property of the transistor becomes more significant and the transistors, conducting more freely as a result of the rise in temperature, causes an increase in the collector current or leakage current. The transistor base-emitter voltage decreases as a result.

With increased heating due to heavy current flow, the transistor is damaged.

Answer:

business

Explanation:

because shopping has great income

Answer:

is ur question right

Explanation:

is ur question right

is ur question right

The records in the table represents the employee ID of each employee. Assume the table name is EMPLOYEES and the field name of employee IDs is ID, the following SQL query inserts Emp3 and Emp4 into the employees table.

INSERT INTO EMPLOYEES (ID) values (Emp3), (Emp4)

The complete question requires that we list the pros and cons of solving the problem using Index sequential access method (ISAM).

The advantage of using ISAM is that priorities are given to the indices of the records being inserted. So, Emp3 and Emp4 will be inserted immediately after Emp2.

However, a major disadvantage of using ISAM is that it is very expensive to keep the indices in a sequential order;

See attachment for the illustration of Index sequential access method (ISAM).

Read more about Index sequential access method (ISAM) at:

https://brainly.com/question/4692093

Answer:

uhhhhhhh lemme think

Explanation: