Answer:
Correct Answer:
A. water pump
Explanation:
Timing belt in a vehicle helps to ensure that crankshaft, pistons and valves operate together in proper sequence. Timing belts are lighter, quieter and more efficient than chains that was previously used in vehicles.
Most car manufacturers recommended that, when replacing timing belt, tension assembly, water pump, camshaft oil seal should also be replaced with it at same time.
Assume that the heat is transferred from the cold reservoir to the hot reservoir contrary to the Clausis statement of the second law. Prove that this violates the increase of entropy principle—as it should according to Clausius.
Answer: hello attached below is the diagram which is part of your question
Total entropy change = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k it violates Clausius increase of entropy which is Sgen > 0
Explanation:
Clausius statement states that it is impossible to transfer heat energy from a cooler body to a hotter body in a cycle or region without any other external factors affecting it .
applying the increase in entropy principle to prove this
temp of cold reservoir (t hot)= 600 k
temp of hot reservoir(t cold) = 1220 k
energy (q) = 100 kj
total entropy change = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k
entropy change in cold reservoir = Q/t cold = 100 / 600 = -0.166 kj/k
entropy change in hot reservoir = Q / t hot = 100 / 1220 = 0.083 kj/k
hence it violates Clausius inequality of increase of entropy principle which is states that generated entropy has to be > 0
Calculate the current in the 8-W resistor of Figure below by using Thevenin’s theorem. What will be its value of connections of 6V battery are reversed
solution from c hegg. hope it helps. see photos explanation
can you solve it please
Answer:
nosenose
Explanation:
aaaaaaaaaaaa
The plate is made of steel having a density of 7910 kg/m3 .If the thickness of the plate is 9 mm , determine the horizontal and vertical components of reaction at the pin A and the tension in cable BC.
Answer:
Horizontal component ( Ax) = 0
vertical component ( Ay ) = 1794.87 N
Explanation:
Attached below is the detailed solution and the free body diagram of the question
given data:
density = 7910 kg/m3
thickness of plate = 9 mm = 0.009
determine the horizontal and vertical components of the reaction at the pin A and the tension in the cable BC
(A) Derive planar density expressions for BCC (100) and (110) planes in terms of the atomicradius R.
(B) Compute and compare planar density values for these same two planes for molybdenum (Mo).
Answer:
Explanation:
BCC structure can also be called Body-Centred Cubic. In BCC Structure, single atom is located at every corner of the cube, and one is also located at the centre of the structure.
Each of the four cube corners through which this (110) plane travels has an atom, which it shares with four neighboring unit The percentage of the entire crystallographic plane area that is occupied by atoms is known as planar density.
What is planar density ?The packing density of crystals is measured by planar density. A face-centered cubic unit cell's planar density may be determined by following a few straightforward procedures. Determine how many atoms are centered on a certain plane. An FCC crystal, for instance, has 2 atoms on a (1 1 0) plane.
The amount of atoms per unit area on an interest plane defines the planar density, a crucial aspect of a crystal structure.
The percentage of the entire crystallographic plane area that is occupied by atoms is known as planar density. Atomic packing factor analogs in one and two dimensions are linear and planar densities.
Thus, The center atom, however, is totally contained within the unit cell. This means that this BCC (110) plane has an equivalent of 2 atoms.
To learn more about planar density follow the link;
https://brainly.com/question/17013474
#SPJ5
(2x+y)dx+(x-2y)dy=0 solve the differential equation
Answer: y' = - x'
Explanation:
Let f(x) = 2x + y
then f'(x) = 2 + y'
Let f(y) = x - 2y
then f'(y) = x' - 2
Given: f'(x) + f'(y) = 0
2 + y' + x' - 2 = 0
y' + x'= 0
y' = -x'
This can also be written as: [tex]\dfrac{dy}{dx}=-\dfrac{d}{dx}[/tex]
Consider atmospheric air at 25 C and a velocity of 25 m/s flowing over both surfaces of a 1-m-long flat plate that is maintained at 125 C. Determine the rate of heat transfer per unit width from the plate for values of the critical Reynolds number corresponding to 105 , 5 105 , and 106 .
Answer:
Explanation:
Temperature of atmospheric air To = 25°C = 298 K
Free stream velocity of air Vo = 25 m/s
Length and width of plate = 1m
Temperature of plate Tp = 125°C = 398 K
We know for air, Prandtl number Pr = 1
And for air, thermal conductivity K = 24.1×10?³ W/mK
Here, charectorestic dimension D = 1m
Given value of Reynolds number Re = 105
For laminar boundary layer flow over flat plate
= 3.402
Therefore, hx = 0.08199 W/m²K
So, heat transfer rate q = hx×A×(Tp – To)
= 0.08199×1×(398 – 298)
After a capacitor is fully chargerd, a small amount of current will flow though it. what is this current called?
Answer:
leakage
Explanation:
That current is "leakage current."
You have accumulated several parking tickets while at school, but you are graduating later in the year and plan to return to your home in another jurisdiction. A friend tells you that the authorities in your home jurisdiction will never find out about the tickets when you re-register your car and apply for a new license. What should you do?
Answer:
pay off the parking tickets
Explanation:
In the scenario being described, the best thing to do would be to pay off the parking tickets. The parking tickets stay under your name, and if they are not paid in time can cause problems down the road. For starters, if they are not paid in time the amount will increase largely which will be harder to pay. If that increased amount is also not paid, then the government will suspend your licence indefinitely which can later lead to higher insurance rates.
Armature reaction in a dc machine A) is due to an increase of the armature voltage. B) occurs when the motor is connected to an ac power source. C) occurs when the motor is connected to a dc power source. D) is due to an increase of the armature current.
Answer:
D) is due to an increase of the armature current.
Explanation:
Option D is correct because on the DC motor, when the load increases, it leads to an increase in the armature current.
The armature current then sets up a magnetic flux which opposes the main field flux. The net field flux gets reduced. It is at this point, the armature reaction occurs.
Armature reaction is seen as the effect of magnetic flux which is usually set up by an armature current. This occurs when there is the distribution of flux under the main poles.
There are two effects the armature flux causes on the main field flux.
1. The main field flux is distorted by the armature reaction.
2. The magnitude of the main field flux is reduced by the armature flux.
What is the following diagram called?
Answer:
flow chart
Explanation:
it's a flow chart right ? don't know the explanation cause I am not even sure I am right
Cho biết tác dụng chung của các hệ giằng khung ngang nhà công nghiệp nhẹ 1 tầng 1 nhịp.
A cruise missile under test is moving horizontally at Ma =2 in the atmosphere at an elevation of 2000 m (Air temperature is 2 °C). Determine the half-angle "alpha" of the Mach cone.
Answer: the half-angle "alpha" of the Mach cone = 30⁰
Explanation:
To calculate the half-angle "alpha" of the Mach cone.
we say ;
Sin∝ = 1 / Ma
given that Ma = 2
now we substitute
Sin∝ = 1 / 2
Sin∝ = 0.5
∝ = Sin⁻¹ 0.5
∝ = 30⁰
Therefore, the half-angle "alpha" of the Mach cone is 30⁰
A single-threaded power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 006 for the collar and 009 for the threads, while the frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to raise and lower the load for
Answer:
the torque required to RAISE the load is Tr = 18.09 Nm
the torque required to LOWER the load is Tl = 10.069 ≈ 10.07 Nm
the Overall Efficiency e = 0.2199 ≈ 0.22
Explanation:
Given that; F = 5 kN, p = 5mm, d = 35mm
Dm = d - p/2
Dm = 35 - ( 5/2) = 35 - 2.5
DM = 32.5mm
So the torque required to RAISE the load is
Tr = ( 5 × 32.5)/2 [(5 + (π × 0.09 × 32.5)) / ( (π × 32.5) - ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]
Tr = 81.25 × (14.1892 / 101.6518) + 6.75
Tr = 11.3414 + 6.75
Tr = 18.09 Nm
the torque required to LOWER the load is
Tl = ( 5 × 32.5)/2 [(π × 0.09 × 32.5) - 5) / ( (π × 32.5) + ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]
Tl = 81.25 × 4.1892 / 102.5518 + 6.75
Tl = 3.3190 + 6.75
Tl = 10.069 ≈ 10.07 Nm
So since torque required to LOWER the load is positive
that is, the thread is self locking
Therefore the efficiency is
e = ( 5 × 5 ) / ( 2π × 18.09 )
e = 25 / 113.6628
e = 0.2199 ≈ 0.22
The cold drawn AISI 1040 steel bar with 25-mm width and 10-mm thick has a 6- mm diameter thru hole in the center of the plate. The plate is subjected to a completely reversed axial load that fluctuates from 12kN to 28kN. Use notch sensitivity of 0.83.
Required:
a. Estimate the fatigue factor of safety based on yielding criteria.
b. Estimate the fatigue factor of safety based on Goodman and Morrow criteria.
Answer:
A) ( N ) = 1.54
B) N ( Goodman ) = 1.133, N ( Morrow) = 1.35
Explanation:
width of steel bar = 25-mm
thickness of steel bar = 10-mm
diameter = 6-mm
load on plate = between 12 kN AND 28 kN
notch sensitivity = 0.83
A ) Fatigue factor of safety based on yielding criteria
= δa + δm = [tex]\frac{Syt}{n}[/tex] = 91.03 + 227.58 = 490 / N
therefore Fatigue number of safety ( N ) = 1.54
δa (amplitude stress ) = kf ( Fa/A) = 2.162 * ( 8*10^3 / 190 ) = 91.03 MPa
A = area of steel bar = 190 mm^2 , Fa = amplitude load = 8 KN , kf = 2.162
δm (mean stress ) = kf ( Fm/A ) = (2.162 * 20*10^3 )/ 190 = 227.58 MPa
Fm = mean load = 20 *10^3
B) Fatigue factor of safety based on Goodman and Morrow criteria
δa / Se + δm / Sut = 1 / N
= 91.03 / 183.15 + 227.58 / 590 = 1 /N
Hence N = 1.133 ( based on Goodman criteria )
note : Se = endurance limit (calculated) = 183.15 , Sut = 590
applying Morrow criteria
N = 1 / ( δa/Se) + (δm/ δf )
= 1 / ( 91.03 / 183.15 ) + (227.58 / 935 )
= 1.35
Based on the hardness values determined in Part 1, what is the tensile strength (in MPa) for each of the alloys?
(a) 0.25 wt%C with spheroidite,
(b) 0.25 wt%C with coarse pearlite,
(c) 0.60 wt%C with fine pearlite, and
(d) 0.60 wt%C with coarse pearlite.
The tolerance to all answers is +/-10 %.
Answer:
a. 115
b. 135
c. 220
d. 185
Explanation:
Spheriodite is microscopic constituents in some steels which is composed of spherically shaped cementide particle. It is most ductile and softest type of steel. Pearlite is two phased lamellar compose of alternating layer of ferrite and cementite. It is hard and strong but not tough. It is applied on cutting tools like chopper, blades and knives.
Which of the following is not a category of electrical burns
prove that Sin^6 ϴ-cos^6ϴ=(2Sin^2ϴ-1)(cos^2ϴ+sin^4ϴ) please sove step by step with language it is opt maths question guys i willl give you 100 point and mark as brainlest answer
A resistor has code 104 printed on it .What is the resistive value of this resistor
Answer:
X = 1 (1st digit in the code)
Y = 0 (2nd digit)
Z = 4 (3rd multiplier digit)
104 → 10 × 10^4 Ω
→ 10 × 10000Ω
→ 100 kΩ
resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).
Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.
When we use numbers, let's assume that we have 3 single-digit numbers abc.
So if the code in our resistor is abc, this will mean that the resistance of the resistor is:
ab×10^c Ω
Using this general rule we can see that if the code is 104, then the resistance will be:
r = 10×10^4 Ω
= 100,000 Ω
Then we can conclude that the resistive value of this resistor is 100,000 Ω
If you want to learn more, you can read:
https://brainly.com/question/74415
what scale model proves the initial concept?
Answer: A prototype
Explanation:
The scale model that proves the initial concept is called a domain model.
What is a scale model?A copy or depiction of something where all parts have the same dimensions as the original. A scale model is an image or copy of an object that is either larger or smaller than the object being represented's actual size.
A domain model is a type of conceptual model that is used to depict the structural elements and conceptual constraints within a domain of interest.
A domain model will include all of the entities, their attributes, and relationships, as well as the constraints that govern the conceptual integrity of the structural model elements that comprise that problem domain.
Therefore, a domain model is the scale model that proves the initial concept.
To learn more about the scale model, refer to the below link:
https://brainly.com/question/14341149
#SPJ2
All hermetic compressors require a crankshaft seal.
True
False
A cylinder is to be cast out of aluminum. The diameter of the disk is 500 mm and its thickness is 20 mm. The mold constant 2.0 sec/mm2 in Chvorinov's formula to calculate the solidification time.
Required:
a. Calculate the minimum time (minutes) for the casting to solidify.
b. Discuss if the result in part (a) is the same when casting grey cast iron.
Answer:
a) the minimum time (minutes) for the aluminium casting to solidify is 2.86 min
b) the minimum time (minutes) for the grey iron casting to solidify is 2.13 min. Therefore solidification of grey iron cast will take less time (2.13 min) compared to the solidification of the aluminium cast (2.86 min)
Explanation:
Given that; diameter of Disk = 500 mm, thickness t = 20, mold constant Cm = 2.0 sec/mm²
first we find the volume and Area;
Volume V = πD²t / 4
Volume V = π × (500)² × 20 / 4 = 3,926,991 mm³
Area A = 2πD²/ 4 + πDt
Area A = {[π × (500)²] / 2} +{ π × (500) × (20)}
Area A = 392,699.08 + 31,415.93
Area A = 424,115 mm²
a)
Chvorinov’s rule
T(aluminium) = Cm (V/A) ²
T(aluminium) = 2.0 × (3,926,991 / 424,115) ²
T(aluminium) = 171.5 s = 2.86 min
∴ the minimum time (minutes) for the casting to solidify is 2.86 min
b)
For cast iron
Cm (mold constant = 1.488 sec/mm²)
Chvorinov’s rule
T(iron) = Cm (V/A) ²
T(iron) = 1.488 × (3,926,991 / 424,115) ²
T(iron) = 127.5720s = 2.13 min
Therefore solidification of grey iron cast will take less time (2.13 min) compared to the solidification of the aluminium cast (2.86 min)
A plate is supported by a ball-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem?
Answer:
There are five (5) unknown support reactions in this problem.
Explanation:
A roller joint rotates and translates along the surface on which the roller rests. The resulting reaction force is always a single force that is perpendicular to, and away from, the surface. This allows the roller to move in a single plane along the surface where it rests.
A cable support provides support in one direction, parallel, and in opposite direction to the load on it. There exists a single reaction from the cable pointed upwards.
A ball-and-socket joint have reaction forces in all 3 cardinal directions. This allows it to move in the x-y-z plane.
The total unknown reactions on the member are five in number.
The solid homogeneous cylinder is released from rest on the ramp. If θ= 40° , µs= 0.30 and µk= 0.20. Determine the magnitudes of the acceleration of the mass (W= 8lb) center G and the friction force exerted by the ramp on the cylinder.
Answer:
A) 13.80 ft/s^2
B) 1.714 Ib
Explanation:
Magnitude of acceleration center G
mass = W / g = 8 / 32.2 = 0.2484 Ib.s^2/ft
calculate the acceleration along x direction
A = ra
r = radius
a = angular acceleration
A = 6 in [tex]\frac{1 ft}{12 in}[/tex] * a
a= 2A
equation of the plane along the x-direction
w sin∅ - F = ma
8* sin40 - F = 0.2484 * a
hence F = 5.1423 - 0.2484 a
next find the moment of inertia along the z axis
I = 1/2 mr^2
= 1/2 * 0.2484 * (6/12)^2 = 0.03105 Ib.ft.s^2
Applying moment balance equation
F * r = inertia * a
(5.1423 - 0.2484 a)*0.5 = 0.03105 * 2A
2.57115 = 0.1863 A hence
A = 13.80 ft/s^2 ( acceleration of the cylinder )
B) Calculate the friction force exerted by the ramp on the cylinder
F = 5.1423 - 0.2484 A
= 5.1423 - 0.2484 ( 13.80 )
= 1.714 Ib
The magnitudes of the acceleration and the friction force are;
Acceleration = 13.8 ft/s²
Friction Force = 1.714 lb
The image of the solid homogeneous cylinder is missing and so i have attached it.
From the image we see that;
Weight; W = 8 lbRadius; r = 6 in = 0.5 ftWe are given;
Angle of incline; θ = 40°Coefficient of static friction; µ_s = 0.30 coefficient of kinetic friction; µ_k = 0.20We know that formula for weight is; W = mg
Thus; m = W/g
where g is acceleration due to gravity = 32.2 ft/s²
m = 8/32.2
mass; m = 0.2484 lb.s²/ft
Now, to get the acceleration along the x-axis, we will use the formula;
a = rα
where α is angular acceleration. Thus;
a = 0.5α
α = 2a ----- (eq 1)
Now, resolving forces along the x-direction gives;
W*sinθ - F = ma
Plugging in the relevant values;
8*sin 40 - F = 0.2484a
F = 8*sin 40 - 0.2484a -----(eq 2)
Now, moment of inertia of the cylinder along the z-axis is gotten from;
I = ¹/₂mr²
I = ¹/₂ × 0.2484 × 0.5²
I = 0.03105 lb.ft/s²
Taking equilibrium of moments we have;
F*r = I*α
Thus;
(8*sin 40 - 0.2484a)0.5 = 0.03105α
⇒ 2.57115 - 0.1242a = 0.03105α
⇒ 0.03105α + 0.1242a = 2.57115
From eq 1, α = 2a. Thus;
0.03105(2a) + 0.1242a = 2.57115
0.1863a = 2.57115
a = 2.57115/0.1863
a = 13.8 ft/s²
Formula for the friction force exerted by the ramp on the cylinder is;F = 8*sin 40 - 0.2484a
F = 5.1423 - 0.2484(13.8)
F = 1.714 lb
Read more about cylinder moment of inertia at; https://brainly.com/question/7020147
Consider the thermocouple and convection conditions of Example 1, but now allow for radiation exchange with the walls of a duct that encloses the gas stream. If the duct walls are at 400℃ and the emissivity of the thermocouple bead is 0.9, calculate the steady-state temperature of the junction
Answer:
hello your question has some missing part attached below is the complete question
answer : steady state temperature = 419.713k ≈ 218.7⁰c
Time required to reach a junction ≈ 5 secs
Explanation:
The detailed solution of the given problem is attached below but the solution to the subsequent problem from which the question you asked is referenced to( problem 1 ), is not attached because it was not part of the question you asked
tính toán dung lượng bộ nhớ yêu cầu để lưu trữ 6 phút tiếng nói theo định dàng truyền trong mạng PSTN?
Answer:
hugdxvb huiiiuttyuj ftfrr
When the rod is circular, radial lines remain straight and sections perpendicular to the axis do not warp. In this case, the strains vary linearly along radial lines. Within the proportional limit, the stress also varies linearly along radial lines. If point A is located 12 mm from the center of the rod, what is the magnitude of the shear stress at that point
The question is incomplete. The complete question is :
The solid rod shown is fixed to a wall, and a torque T = 85N?m is applied to the end of the rod. The diameter of the rod is 46mm .
When the rod is circular, radial lines remain straight and sections perpendicular to the axis do not warp. In this case, the strains vary linearly along radial lines. Within the proportional limit, the stress also varies linearly along radial lines. If point A is located 12 mm from the center of the rod, what is the magnitude of the shear stress at that point?
Solution :
Given data :
Diameter of the rod : 46 mm
Torque, T = 85 Nm
The polar moment of inertia of the shaft is given by :
[tex]$J=\frac{\pi}{32}d^4$[/tex]
[tex]$J=\frac{\pi}{32}\times (46)^4$[/tex]
J = 207.6 [tex]mm^4[/tex]
So the shear stress at point A is :
[tex]$\tau_A =\frac{Tc_A}{J}$[/tex]
[tex]$\tau_A =\frac{85 \times 10^3\times 12 }{207.6}$[/tex]
[tex]$\tau_A = 4913.29 \ MPa$[/tex]
Therefore, the magnitude of the shear stress at point A is 4913.29 MPa.
What is the built-in pollution control system in an incinerator called
Explanation:
hbyndbnn☝️
In general, MOSFET'S:___________.
A) are mostly used in switching circuits
B) can be fabricated in much higher densities than BJT'S
C) produce simpler circuits than BJTS
D) all of the above
Answer:
A. Are mostly used in switching circuitsExplanation:
MOSFET: The acronym for "metal oxide semiconductor field-effect transistor" are mostly used in switching circuits.
There are two classes of MOSFET
1. Depletion mode
2. Enhancement mode
Generally a MOSFET is a kind of transistor, it is actually a field effect transistor with tree terminals gate, source and drain terminals, also the MOSFET can be used as an amplifier for the amplification of electronic signals in the electronic circuit/devices
3
Current is measured in units called
Answer:
current is measured in Ampere (A)
Answer:
Ampere (A)
Explanation:
The ampere is defined so the elementary charge e is 1.602 176 634 × 10−19 C or A•s.
Hope this helps <3