Answer:
I hope this is correct!
Explanation:
a) work = (force)(displacement)
We know that d = 5m, now we just need to find the force
We need to calculate the acceleration first using a = v^2 - u^2 / 2d
final velocity (v) = 2.1 m/s , initial velocity (u) = 0 m/s , displacement (d) = 5m
a = 2.1^2 - 0^2 / 2(5)
= 0.441 m/s^2
Now we can find force using f = ma
f = (14kg)(0.441m/s^2)
= 6.174 newtons
Finally, you can calculate work now that you have force!
work = (6.174n)(5m)
= 30.87 J (you may need to round sig figs!)
b) Work done by friction = (coefficient of kinetic friction)(mg)(v)
m = 14kg, g = 9.8, coefficient of friction = 0.2
force due to friction = (0.2)(14kg x 9.8)(2.1)
= 57.624 J (again you may need to round to sig figs)
c) Work you perform = total work in direction of motion + work done by friction
total work = 30.87 J, work done by friction = 57.624 J
Work you perform = 30.84 + 57.624
= 88.464 J
d) Force you applied = work you performed / distance
work you performed = 88.464 / 5 m
= 17.6929 N (again you may need to round to sig figs)
Hope this helps ya! Best of luck <3
A student wants to create a 6.0V DC battery from a 1.5V DC battery. Can this be done using a transformer alone
Answer:
Therefore, we need an invert, and a rectifier, along with the transformer to do the job.
Explanation:
A transformer, alone, can not be used to convert a DC voltage to another DC voltage. If we apply a DC voltage to the primary coil of the transformer, it will act as short circuit due to low resistance. It will cause overflow of current through winding, resulting in overheating pf the transformer.
Hence, the transformer only take AC voltage as an input, and converts it to another AC voltage. So, the output voltage of a transformer is also AC voltage.
So, in order to convert a 6 V DC to 1.5 V DC we need an inverter to convert 6 V DC to AC, then a step down transformer to convert it to 1.5 V AC, and finally a rectifier to convert 1.5 V AC to 1.5 V DC.
Therefore, we need an invert, and a rectifier, along with the transformer to do the job.
Consider two parallel plate capacitors. The plates on Capacitor B have half the area as the plates on Capacitor A, and the plates in Capacitor B are separated by twice the separation of the plates of Capacitor A. If Capacitor A has a capacitance of CA-17.8nF, what is the capacitance of Capacitor? .
Answer:
CB = 4.45 x 10⁻⁹ F = 4.45 nF
Explanation:
The capacitance of a parallel plate capacitor is given by the following formula:
C = ε₀A/d
where,
C = Capacitance
ε₀ = Permeability of free space
A = Area of plates
d = Distance between plates
FOR CAPACITOR A:
C = CA = 17.8 nF = 17.8 x 10⁻⁹ F
A = A₁
d = d₁
Therefore,
CA = ε₀A₁/d₁ = 17.8 x 10⁻⁹ F ----------------- equation 1
FOR CAPACITOR B:
C = CB = ?
A = A₁/2
d = 2 d₁
Therefore,
CB = ε₀(A₁/2)/2d₁
CB = (1/4)(ε₀A₁/d₁)
using equation 1:
CB = (1/4)(17.8 X 10⁻⁹ F)
CB = 4.45 x 10⁻⁹ F = 4.45 nF
If one could transport a simple pendulum of constant length from the Earth's surface to the Moon's, where acceleration due to gravity is one-sixth (1/6) that on the Earth, by what factor would be the pendulum frequency be changed
Answer:
The frequency will change by a factor of 0.4
Explanation:
T = 2(pi)*sqrt(L/g)
Since g(moon) = (1/6)g(earth), the period would change by sqrt[1/(1/6)] = sqrt(6) ~ 2.5 times longer on the moon. Since the period & frequency are inverses, the frequency would be 1/2.5 or 0.4 times shorter on the moon.
If 1.7 kg of 238Pu is required to power the spacecraft's data transmitter, for how long after launch would scientists be able to receive data? Round to the nearest year. Do not round intermediate calculations.
The question is incomplete. Here is the complete question.
The isotope of Plutonium 238Pu is used to make thermoeletric power sources for spacecraft. Suppose that a space probe was launched in 2012 with 3.5 kg of 238Pu.
(a) If the half-life of 238Pu is 87.7 yr, write a function of the form [tex]Q(t)=Q_{0}e^{-kt}[/tex] to model the quantity Q(t) of 238Pu left after t years. Round ythe value of k to 3 decimal places. Do not round intermediate calculations.
(b) If 1.7kg of 238Pu is required to power the spacecraft's data transmitter, for low long after launch would scientists be able to receive data? Round to the nearest year. Do not round intermediate calculations.
Answer: (a) [tex]Q(t)=3.5e^{-0.0079t}[/tex]
(b) 91 years.
Explanation:
(a) Half-life is time it takes a substance to decrease to half of itself, i.e.:
Q(t) = [tex]0.5Q_{0}[/tex]
[tex]0.5Q_{0}=Q_{0}e^{-87.7k}[/tex]
[tex]0.5=e^{-87.7k}[/tex]
[tex]ln(0.5)=ln(e^{-87.7k})[/tex]
[tex]ln(0.5)=-87.7k[/tex]
[tex]k = \frac{ln(0.5)}{-87.7}[/tex]
k = 0.0079
Knowing k and [tex]Q_{0}[/tex]=3.5kg, function is [tex]Q(t)=3.5e^{-0.0079t}[/tex]
(b) Using function:
[tex]Q(t)=3.5e^{-0.0079t}[/tex]
[tex]1.7=3.5e^{-0.0079t}[/tex]
[tex]e^{-0.0079t}=\frac{1.7}{3.5}[/tex]
[tex]e^{-0.0079t}=0.4857[/tex]
[tex]ln(e^{-0.0079t})=ln(0.4857)[/tex]
[tex]-0.0079t=-0.7221[/tex]
[tex]t = \frac{-0.7221}{-0.0079}[/tex]
t = 91.41
t ≈ 91 years
Scientists will be able to receive data for approximately 91 years.
A stonecutter's chisel has an edge area of 0.7 cm2. If the chisel is struck with a force of 42 N, what is the pressure exerted on the stone
Answer:
The pressure is [tex]P = 583333 \ N/m^2[/tex]
Explanation:
From the question we are told that
The area of the edge is [tex]A = 0.72 cm^2 = 0.72 *10^{-4}\ m[/tex]
The force is [tex]F = 42 \ N[/tex]
The pressure is mathematically represented as
[tex]P = \frac{F}{A}[/tex]
substituting values
[tex]P = \frac{42}{0.72*10^{-4}}[/tex]
[tex]P = 583333 \ N/m^2[/tex]
A circular loop of wire has radius of 9.50 cmcm. A sinusoidal electromagnetic plane wave traveling in air passes through the loop, with the direction of the magnetic field of the wave perpendicular to the plane of the loop. The intensity of the wave at the location of the loop is 0.0215 W/m2W/m2, and the wavelength of the wave is 6.90 mm.What is the maximum emf induced in the loop?
Express your answer with the appropriate units.
Answer:
The induced emf is [tex]\epsilon = 0.1041 \ V[/tex]
Explanation:
From the question we are told that
The radius of the circular loop is [tex]r = 9.50 \ cm = 0.095 \ m[/tex]
The intensity of the wave is [tex]I = 0.0215 \ W/m^2[/tex]
The wavelength is [tex]\lambda = 6.90\ m[/tex]
Generally the intensity is mathematically represented as
[tex]I = \frac{ c * B^2 }{ 2 * \mu_o }[/tex]
Here [tex]\mu_o[/tex] is the permeability of free space with value
[tex]\mu_o = 4 \pi *10^{-7} N/A^2[/tex]
B is the magnetic field which can be mathematically represented from the equation as
[tex]B = \sqrt{ \frac{ 2 * \mu_o * I }{ c} }[/tex]
substituting values
[tex]B = \sqrt{ \frac{ 2 * 4\pi *10^{-7} * 0.0215 }{ 3.0*10^{8}} }[/tex]
[tex]B = 1.342 *10^{-8} \ T[/tex]
The area is mathematically represented as
[tex]A = \pi r^2[/tex]
substituting values
[tex]A = 3.142 * (0.095)^2[/tex]
[tex]A = 0.0284[/tex]
The angular velocity is mathematically represented as
[tex]w = 2 * \pi * \frac{c}{\lambda }[/tex]
substituting values
[tex]w = 2 * 3.142 * \frac{3.0*10^{8}}{ 6.90 }[/tex]
[tex]w = 2.732 *10^{8} rad \ s^{-1}[/tex]
Generally the induced emf is mathematically represented as
[tex]\epsilon = N * B * A * w * sin (wt )[/tex]
At maximum induced emf [tex]sin (wt) = 1[/tex]
So
[tex]\epsilon = N * B * A * w[/tex]
substituting values
[tex]\epsilon = 1 * 1.342 *10^{-8} * 0.0284 *2.732 *10^{8}[/tex]
[tex]\epsilon = 0.1041 \ V[/tex]
A solid metal sphere of radius 3 m carries a total charge of -5.5 uc. What is the magnitude of the
electric field at a distance from the sphere's center of (a) 2.9 m and (b) 8 m? How would the answers
differ if the sphere was (c) a thin shell.
IN
Answer:
2.9::: 5.87*10*3 N/C
8: 7.73 × 10 ^2 N/C
Explanation: https://study.com/academy/answer/a-solid-metal-sphere-of-radius-3-00-m-carries-a-total-charge-of-5-50-muc-what-is-the-magnitude-of-the-electric-field-at-each-of-the-following-distances-from-the-sphere-s-center-a-3-10-m-b-8-00-m.html
You're conducting an experiment on another planet. You drop a rock from a height of 1 m and it hits the ground 0.4 seconds later. What is acceleration due to gravity on the planet ?
Answer:
Here,
v (final velocity) = 0
u (initial velocity) = u
a = ?
s = 1m
t = 0.4s
using the first equation of motion,
0 = u + 0.4a
= -0.4a = u
using the second equation of motion:
1 = 0.4u + 0.08a
from the bold equation
1 = 0.4(-0.4a) + 0.08a
1 = -0.16a + 0.08a
1 = -0.08a
a = -1/0.08
a = -100/8
a = -12.5 m/s/s
please make me brainly, i am 1 brainly away from the next rank
Ayudaaa :(
Calcula la resistencia total del siguiente circuito eléctrico.
If you wish to observe features that are around the size of atoms, say 5.5 × 10^-10 m, with electromagnetic radiation, the radiation must have a wavelength of about the size of the atom itself.
Required:
a. What is its frequency?
b. What type of electromagnetic radiation might this be?
Answer:
a) 5.5×10^17 Hz
b) visible light
Explanation:
Since the wavelength of the electromagnetic radiation must be about the size of the about itself, this implies that;
λ= 5.5 × 10^-10 m
Since;
c= λ f and c= 3×10^8 ms-1
f= c/λ
f= 3×10^8/5.5 × 10^-10
f= 5.5×10^17 Hz
The electromagnetic wave is visible light
A 384 Hz tuning fork produces standing waves with a wavelength of 0.90 m inside a resonance tube. The speed of sound at experimental conditions is
Answer:
v = 345.6m/s
Explanation:
v = 384 x 0.9 = 345.6
v = 345.6m/s
Which of the following statements is true vibrations ?
Answer:
C. Neither ultrasonic nor infrasonic vibrations can be heard by humans.
Explanation:
The complete question is
Which of the following statements is true of vibrations? A. The frequency of infrasonic vibrations is much too high to be heard by humans. B. Ultrasonic vibrations have a frequency lower than the range for normal hearing. C. Neither ultrasonic nor infrasonic vibrations can be heard by humans. D. Infrasonic vibrations are used in sonar equipment and to detect flaws in steel castings.
Ultrasonic vibrations have frequencies higher than our range of hearing, while infrasonic vibrations have frequencies lower than our range of hearing. Ultrasonic vibrations or sound is used in sonar equipment, and is used for detecting hidden flaws in steel castings and structures. Both infrasonic and ultrasonic fall below and above our normal hearing range respectively, and are only audible to dogs, cats, and some other mammals.
Answer:
Answer is " Two bodies with the same vibration frequency that are placed next to each other will exhibit sympathetic vibrations as one body causes the other to vibrate."
Explanation:
My options were:
A) Forced vibrations, such as those between a tuning fork and a large cabinet surface, result in a much lower sound than was produced by the original vibrating body.
B) Resonance occurs as a result of sympathetic vibrations.
C) A non-vibrating object can begin to vibrate as a result of forced vibrations.
D) Two bodies with the same vibration frequency that are placed next to each other will exhibit sympathetic vibrations as one body causes the other to vibrate.
A is correct
.
30 POINTS HELP PLEASE
A galvanometer consists of a loop of wire in a magnetic field.
Question 19 options:
True
False
Answer:
A galvanometer consists of a loop of wire in a magnetic field.
TRUE
An electromagnetic flowmeter is useful when it is desirable not to interrupt the system in which the fluid is flowing (e.g. for the blood in an artery during heart surgery). Such a device is illustrated. The conducting fluid moves with velocity v in a tube of diameter d perpendicular to which is a magnetic field B. A voltage V is induced between opposite sides of the tube. Given B = 0.120 T, d = 1.2 cm., and a measured voltage of 2.88 mV, determine the speed of the blood.
Answer:
2 m/s
Explanation:
The electromagnetic flow-metre work on the principle of electromagnetic induction. The induced voltage is given as
[tex]E = Blv[/tex]
where [tex]E[/tex] is the induced voltage = 2.88 mV = 2.88 x 10^-3 V
[tex]l[/tex] is the distance between the electrodes in this field which is equivalent to the diameter of the tube = 1.2 cm = 1.2 x 10^-2 m
[tex]v[/tex] is the velocity of the fluid through the field = ?
[tex]B[/tex] is the magnetic field = 0.120 T
substituting, we have
2.88 x 10^-3 = 0.120 x 1.2 x 10^-2 x [tex]v[/tex]
2.88 x 10^-3 = 1.44 x 10^-3 x [tex]v[/tex]
[tex]v[/tex] = 2.88/1.44 = 2 m/s
A boat having stones floats in water. If stones are unloaded in water, what will happen to the level of water?
Answer:
A boat having stones floats in water. If stones are unloaded in water, what will happen to the level of water?
Explanation:
What is an understood decimal
Which statement about friction is true? (1 point)
o
Static friction and kinetic friction in a system always act in opposite directions of each other and in the same direction as the
applied force
Static friction and kinetic friction in a system always act in the same direction as each other and in the opposite direction of the
applied force
Static friction and kinetic friction in a system always act in opposite directions of each other and in the opposite direction of the
applied force
O
Static friction and kinetic friction in a system always act in the same direction as each other and in the same direction as the
applied force.
Answer:static friction and kinetic friction in a system always act in the same direction as each other and n the opposite direction of the applie force . Is the correct answer
Explanation:
Static friction and kinetic friction in a system always act in the same direction as each other and in the opposite direction of the applied force. The correct option is B.
What is friction?Friction is the force that prevents one hard material from scooting or rolling over the other.
Frictional forces, such as the locomotion required to walk without dropping, are advantageous, but they also create a significant amount of resistance to motion.
We can control cars because of friction between the tires and the road: more precisely, because there are three types of friction: rolling friction, starting friction, and sliding friction.
Friction reduces the speed of moving objects and can even stop them from moving. The friction between the objects generates heat. As a result, energy is wasted in the machines. Friction will cause wear and tear on the machine parts.
In a system, static and kinetic friction always act in the same direction and in the opposite direction of the applied force.
Thus, the correct option is B.
For more details regarding friction, visit:
https://brainly.com/question/28356847
#SPJ2
if you jog at a speed of 1.5m/s for 20 seconds how far di you travel
Answer: 30m
Explanation:
Given:
Speed: 1.5m/s
Time: 20 seconds
Distance = speed × time
Distance = 1.5 × 20
= 30m
Therefore you will travel 30m
Must click thanks and mark brainliest
If 50 mL of each of the liquids in the answer choices were poured into a 250 mL beaker, which layer would be directly above a small rubber ball with a density of 0.960 g/mL? A. sea water – density of 1.024 g/mL B. mineral oil – density of 0.910 g/mL C. distilled water – density of 1.0 g/mL D. petroleum oil – density of 0.820 g/mL
Answer:
B. mineral oil – density of 0.910 g/mL.
Explanation:
Hello,
In this case, since the density is known as the degree of compactness a body has (mass in the occupied volume), the higher the density, the higher the weight of the body, therefore, if submerged into a liquid it could float if less dense than the liquid or sink if more dense than the liquid.
In such a way, since the rubber is more dense than mineral (0.960 g/mL > 0.910 g/mL) oil but less dense than distilled water (0.960 g/mL < 1.0 g/mL) we can say that B. mineral oil – density of 0.910 g/mL is directly above it when submerged.
Best regards.
A disk between vertebrae in the spine is subjected to a shearing force of 375 N. Find its shear deformation, taking it to have a shear modulus of 1.60×109 N/m2. The disk is equivalent to a solid cylinder 0.750 cm high and 6.50 cm in diameter.
Answer:
5.29×10^-7
Explanation:
shear stress τ = F/ A
shear deformation δ = (VL)/ (AG)
= (τL)/ G
V=shear force
L=height of disk=6.50×10^-2
A=cross sectional area
G= shear modulus= (1.60x10^9N/m^2)
A=πd^2/4
Then substitute the values we have
4×(375N)(0.00750m)
________________ = δ
(π*0.00650^2)(1.60x10^9N/m^2)
= 5.29×10^-7
If R = 20 Ω, what is the equivalent resistance between points A and B in the figure?
Answer:
c. 70 Ω
Explanation:
The R and R resistors are in parallel. The 2R and 2R resistors are in parallel. The 4R and 4R resistors are in parallel. Each parallel combination is in series with each other. Therefore, the equivalent resistance is:
Req = 1/(1/R + 1/R) + 1/(1/2R + 1/2R) + 1/(1/4R + 1/4R)
Req = R/2 + 2R/2 + 4R/2
Req = 3.5R
Req = 70Ω
Electrons are accelerated through a voltage difference of 270 kV inside a high voltage accelerator tube. What is the final kinetic energy of the electrons?
Each electron winds up with kinetic energy of
(270 keV)
plus
(whatever KE it had when it started accelerating).
2- A student ran 135 meters in 15 seconds. What was the student's velocity?
*
7.5 m/s
9 m/s
12 m/s
15 m/s
Answer:
9 Brainly hahaha ............huh
A woman pulls on a 6.00-kg crate, which in turn is connected to a 4.00-kg
crate by a light rope. The light rope remains taut. Compared to the 6.00-kg crate,
the lighter 4.00-kg crate
Please explain why any of these multiple choices is correct!
Answer:
B. is subject to a smaller net force but same acceleration.
Explanation:
F = m*a
So because our force applied is constant from the women pulling on the rope which means the acceleration is the same on both the 4kg create and the 6kg create. The only thing that changes here is the mass of the creates, so there is more tension force between the women and the 6kg create then there is between the 4kg create and the 6kg. It takes less force to move the 4kg create therefore the tension force is less between the two creates.
The net force on both crates is the same and the acceleration of both crates is the same.
The given parameters;
mass of the crate, m = 6 kgmass of the second crate, = 4 kgThe force on the 4kg crate is calculated as follows;
[tex]F_{4kg } = T + F[/tex]
The force on the 6kg crate is calculated as follows;
[tex]F_{6 kg} = -T + F[/tex]
The net force on both crates is calculated as follows;
[tex]\Sigma F= -T + F - (T + F)\\\\\Sigma F= -2T[/tex]
Thus, we can conclude that the net force on both crates is the same and the acceleration of both crates is the same.
Learn more here:https://brainly.com/question/14361879
A circular loop in the plane of a paper lies in a 0.45 T magnetic field pointing into the paper. The loop's diameter changes from 17.0 cm to 6.0 cm in 0.53 s.
A) Determine the direction of the induced current.
B) Determine the magnitude of the average induced emf.
C) If the coil resistance is 2.5 Ω, what is the average induced current?
Answer:
(A). The direction of the induced current will be clockwise.
(B). The magnitude of the average induced emf 16.87 mV.
(C). The induced current is 6.75 mA.
Explanation:
Given that,
Magnetic field = 0.45 T
The loop's diameter changes from 17.0 cm to 6.0 cm .
Time = 0.53 sec
(A). We need to find the direction of the induced current.
Using Lenz law
If the direction of magnetic field shows into the paper then the direction of the induced current will be clockwise.
(B). We need to calculate the magnetic flux
Using formula of flux
[tex]\phi_{1}=BA\cos\theta[/tex]
Put the value into the formula
[tex]\phi_{1}=0.45\times(\pi\times(8.5\times10^{-2})^2)\cos0[/tex]
[tex]\phi_{1}=0.01021\ Wb[/tex]
We need to calculate the magnetic flux
Using formula of flux
[tex]\phi_{2}=BA\cos\theta[/tex]
Put the value into the formula
[tex]\phi_{2}=0.45\times(\pi\times(3\times10^{-2})^2)\cos0[/tex]
[tex]\phi_{2}=0.00127\ Wb[/tex]
We need to calculate the magnitude of the average induced emf
Using formula of emf
[tex]\epsilon=-N(\dfrac{\Delta \phi}{\Delta t})[/tex]
Put the value into t5he formula
[tex]\epsilon=-1\times(\dfrac{0.00127-0.01021}{0.53})[/tex]
[tex]\epsilon=0.016867\ V[/tex]
[tex]\epsilon=16.87\ mV[/tex]
(C). If the coil resistance is 2.5 Ω.
We need to calculate the induced current
Using formula of current
[tex]I=\dfrac{\epsilon}{R}[/tex]
Put the value into the formula
[tex]I=\dfrac{0.016867}{2.5}[/tex]
[tex]I=0.00675\ A[/tex]
[tex]I=6.75\ mA[/tex]
Hence, (A). The direction of the induced current will be clockwise.
(B). The magnitude of the average induced emf 16.87 mV.
(C). The induced current is 6.75 mA.
The kinetic energy of a particle of mass 500g is 4.8j. Determine the velocity of the particle
Answer:
4.38 m/s
Explanation:
You want the current amplitude through a 0.450 mH inductor (part of the circuitry for a radio receiver) to be 1.50 mA when a sinusoidal voltage with an amplitude of 13.0 V is applied across the inductor. What frequency is required?
Answer:
3.067MHzExplanation:
The formula for calculating the voltage across an inductor is expressed as
[tex]V_l = IX_l\\\\Since\ X_l = 2\pi fL\\V_l = I(2\pi fL)[/tex]
Given parameters
current amplitude I = 1.50mA = 1.5*10⁻³A
inductance L = 0.450mH = 0.450*10⁻³H
Voltage across the inductor [tex]V_l[/tex] = 13.0V
Required
frequency f
Substituting the given parametres into the formula, we have;
[tex]V_l = I(2\pi fL)\\\\13 = 1.50*10^{-3}(2*3.14*f*0.450*10^{-3})\\\\13 = 4.239*10^{-6}f\\\\f = \frac{13}{4.239*10^{-6}} \\\\f = 3,066,761 Hertz\\\\f = 3.067MHz[/tex]
Hence, the frequency required is 3.067MHz
please help !!!!!!!!!!
Answer:
Lighthouse 1 during the day will be warmer, lighthouse 2 during the night will be warmer.
Explanation:
As the paragraph stated land absorbs heat and heats up faster than water. So during the day the lighthouse farthest away from the water will be hotter. But then the converse is true also land losses heat faster than water at night. So the water retains the heat from the day better making the lighthouse by the water warmer at night.
"A thin film with an index of refraction of 1.50 is placed in one of the beams of a Michelson interferometer. If this causes a shift of 8 bright fringes in the pattern produced by light of wavelength 540 nm, what is the thickness of the film?"
Answer:
The film thickness is 4.32 * 10^-6 m
Explanation:
Here in this question, we are interested in calculating the thickness of the film.
Mathematically;
The number of fringes shifted when we insert a film of refractive index n and thickness L in the Michelson Interferometer is given as;
ΔN = (2L/λ) (n-1)
where λ is the wavelength of the light used
Let’s make L the subject of the formula
(λ * ΔN)/2(n-1) = L
From the question ΔN = 8 , λ = 540 nm, n = 1.5
Plugging these values, we have
L = ((540 * 10^-9 * 8)/2(1.5-1) = (4320 * 10^-9)/1 = 4.32 * 10^-6 m
If the magnetic field of an electromagnetic wave is in the +x-direction and the electric field of the wave is in the +y direction, the wave is traveling in what direction? Explain your answer.
Answer:
Explanation:
The direction of propagation of electromagnetic wave
is given by the direction of vector E x B where E is electrical field , B is magnetic field .
Given Electric field = E i because it is along x axis
Magnetic field = Bj because it is along y axis
E x B = Ei x Bj
= EB k .
so direction of E x B is along k direction or z - axis so wave is propagating along z - axis .
The direction of motion of electromagnetic wave will be +z-direction.
Electromagnetic waves are waves that consist of the electric field and magnetic field.
The electric and magnetic fields are perpendicular to each other and the wave propagates in the direction perpendicular to both the fields.
Now, the direction of wave motion can be estimated by taking the cross-product of directional unit vectors of the electric and magnetic fields.
The electric field is in the +y direction and the magnetic field is in the +x-direction.
So, the direction of the wave will be,
[tex]i\times j=k[/tex]
Therefore, the direction of motion of electromagnetic wave will be +z-direction.
For more details, refer to the link:
https://brainly.com/question/8553652