A pump is to deliver 10, 000 kg/h of toluene at 1140C and 1.1 atm absolute pressure from the Reboiler of a distillation tower to the second distillation unit without cooling the toluene before it enters the pump. If the friction loss in the line between the Reboiler and the pump is 7 kN/m2. The density of toluene is 886 kg/m3. How far above the pump must the liquid be maintained to avoid cavitation

Answer:

Rp = 3.04×10² Ω.

Explanation:

From the question given:

1/Rp = 1/4.5×10² Ω + 1/ 9.4×10² Ω

Rp =?

We can obtain the value of Rp as follow:

1/Rp = 1/4.5×10² + 1/ 9.4×10²

Find the least common multiple (lcm) of 4.5×10² and 9.4×10².

The result is 4.5×10² × 9.4×10²

Next, divide the result of the lcm by each denominator and multiply the result obtained with the numerator as shown below:

1/Rp = (9.4×10² + 4.5×10²) /(4.5×10²) (9.4×10²)

1/Rp = 13.9×10²/4.23×10⁵

Cross multiply

Rp × 13.9×10² = 4.23×10⁵

Divide both side by 13.9×10²

Rp = 4.23×10⁵ / 13.9×10²

Rp = 3.04×10² Ω.

Answer:

1.931 kilometres is the answer of 1.2 miles

Answer and Explanation:

1 mile = 1.609 km

Set up a fraction to cancel the miles to get the kilometers.

[tex]\frac{1.2mi}{?km} *\frac{1.609}{1mi} = 1.9308km[/tex] <- This is the answer.

#teamtrees #PAW (Plant And Water)

Answer:

b

Explanation:

Answer:a) 4+8+24=36

B) 1/4+1/8+1/24=10

C) yu will connect them in parallel connection.

D) you will connect two in parallel then the remaining one in series to the ons connected in parallel.

Explanation:

(a)The maximum resistance that can be produced using all three resistors will be 36 ohms.

(b)The minimum resistance that can be produced using all three resistors will be 10 ohms.

(c)The three resistors to obtain a resistance of 10.0 Ω will be in the parallel connection.

(d) You connect these three resistors to obtain a resistance of 8.00 Ω will be in parallel. Two will be linked in parallel, and the last one will be connected in series to the two that are connected in parallel.

Resistance is a type of opposition force due to which the flow of current is reduced in the material or wire. Resistance is the enemy of the flow of current.

The maximum resistance that can be produced using all three resistors is obtained by adding all the given resistance;

[tex]\rm R_{max}=(4 +8+24 )\ ohms \\\\ R_{max}=36 \ ohms[/tex]

The minimum resistance that can be produced using all three resistors is obtained when connected in the parallel.

[tex]\rm R_{min}=\frac{1}{4} +\frac{1}{8} +\frac{1}{24} \\\\ R_{min}=10 \ ohm[/tex]

(c)The three resistors to obtain a resistance of 10.0 Ω will be in the parallel connection.

(d) You connect these three resistors to obtain a resistance of 8.00 Ω will be in parallel. Two will be linked in parallel, and the last one will be connected in series to the two that are connected in parallel.

Hence,the maximum resistance that can be produced using all three resistors will be 36 ohms.

To learn more about the resistance, refer to the link;

https://brainly.com/question/20708652

#SPJ2

Explanation:

The maximum height of an object, given the initial launch angle and initial velocity is found with:h=v2isin2θi2g h = v i 2 sin 2 ⁡ θ i 2 g .

Answer:

12.2 m

Explanation:

Given:

v₀ = 15.6 m/s

v = 0 m/s

a = -10 m/s²

Find: Δy

v² = v₀² + 2aΔy

(0 m/s)² = (15.6 m/s)² + 2 (-10 m/s²) Δy

Δy = 12.2 m

[tex] \LARGE{ \boxed{ \rm{ \green{Answer:}}}}[/tex]

Given,

Finding the initial kinetic energy,

[tex]\large{ \boxed{ \rm{K.E. = \frac{1}{2}m {v}^{2}}}}[/tex]

⇛ KE = (1/2)mv²

⇛ KE = (1/2)(0.042)(15.6)²

⇛ KE = 5.11 J

|| ⚡By conservation of energy, the potential energy at the highest point will also be 5.11 J, since there is no kinetic energy at the highest point because the ball is not moving (we neglect energy lost due to air resistance, heat, sound, etc.) ⚡||

So, we have:

[tex] \large{ \boxed{ \rm{P.E. = mgh}}}[/tex]

⇛ h = PE/(mg)

⇛ h = 5.11 J /(0.042 × 9.8)

⇛ h = 12.41 m

✏The ball will rise upto a height of 12.41 m

━━━━━━━━━━━━━━━━━━━━

Given that,

Temperature = 10⁸ K

We need to calculate the peak wavelength in the blackbody spectrum

Using formula of peak wavelength

[tex]peak\ wavelength = \dfrac{2.898\times10^{-3}}{T}[/tex]

Where, T= temperature

Put the value into the formula

[tex]peak\ wavelength = \dfrac{2.898\times10^{-3}}{10^{8}}[/tex]

[tex]peak\ wavelength = 2.90\times10^{-11}\ m[/tex]

[tex]peak\ wavelength = 290\ nm[/tex]

This range of wavelength is ultraviolet.

Hence, The peak wavelength in the blackbody spectrum is 290 nm and the range of wavelength is ultraviolet electromagnetic spectrum .

Answer:

Kindly check explanation

Explanation:

Length of race = 5km

Maximum speed = 45 yards

Converting from yards to kilometer :

1km = 1093.613 yards

x = 45 yards

(1093.613 * x) = 45

x = 45 / 1093.613

x = 0.0411480 km

Where x = maximum length for which he can maintain his maximum speed expressed in kilometers.

Therefore, with the available information, it can be concluded that Lamar cannot maintain his maximum speed for the entire 5km race and will only be able maintain his maximum speed for 0.0411 kilometers.

Lamar cannot maintain his maximum speed for the entire 5km race and will only be able maintain his maximum speed for 0.0411 kilometers.

Length of race = 5km

Maximum speed = 45 yards

Converting from yards to kilometer :

1km = 1093.613 yards

x = 45 yards

[tex](1093.613 \times x) = 45[/tex]

[tex]x = 45 \div 1093.613[/tex]

x = 0.0411480 km

here x represent maximum length for which he can maintain his maximum speed expressed in kilometers.

Learn more: https://brainly.com/question/3617478?referrer=searchResults

Answer:

0.367A = Current of both resistors

For resistor 1: 1.89W; For resistor 2: 11.3W

Explanation:

When the resistors are connected in series, the equivalent resistance is the sum of both resistors, that is:

R = 14.0Ω + 84.0Ω = 98.0Ω

Using Ohm's law, we can find the current of the circuit (Is the same for both resistors):

V = RI

V / R = I

36.0V / 98.0Ω = I

Power is defined as:

P = I²*R

For resistor 1:

P = 0.367A²*14.0Ω = 1.89W

For resistor 1:

P = 0.367A²*84.0Ω = 11.3W

Complete question is;

Consider a bus traveling to the west (-x direction) begins to slow down as it approaches a traffic light. Which statement concerning its acceleration in the x direction is correct

a) The bus is decelerating and its acceleration is positive.

b) The bus is decelerating, and its acceleration is negative.

c) The acceleration is zero.

d) A statement cannot be made using the information given.

Answer:

Option A - bus is decelerating and acceleration is positive.

Explanation:

We are told that the bus is travelling in (negative x direction) and begins to slow down. Since the bus is slowing down, it means that the bus is undergoing a negative acceleration which is called deceleration.

Thus, the bus is decelerating.

Since it is moving in the negative x-axis, it means acceleration is now; -(-a) which gives +a.

Thus, bus is decelerating and acceleration is positive.

Answer:

The highest percentage of change corresponds to the thinnest rod, the correct answer is a

Explanation:

For this exercise we are asked to change the length of the bar by the action of a force applied along its length, in this case we focus on the expression of longitudinal elasticity

               F / A = Y ΔL/L

where F / A is the force per unit length, ΔL / L is the fraction of the change in length, and Y is Young's modulus.

In this case the bars are made of the same material by which Young's modulus is the same for all

              ΔL / L = (F / A) / Y

the area of ​​the bar is the area of ​​a circle

               A = π r² = π d² / 4

               A = π / 4 d²

we substitute

              ΔL / L = (F / Y) 4 /πd²

changing length

               ΔL = (F / Y 4 /π) L / d²

The amount between paracentesis are all constant in this exercise, let's look for the longitudinal change

a) values ​​given d and 3L

               ΔL = cte 3L / d²

               ΔL = cte L /d²  3

To find the percentage, we must divide the change in magnitude by its value and multiply by 100.

                ΔL/L % = [(F /Y  4/π 1/d²) 3L ] / 3L 100

                ΔL/L  % = cte 100%

b) 3d and L value, we repeat the same process as in part a

               ΔL = cte L / 9d²

               ΔL = cte L / d² 1/9

               ΔL / L% = cte 100/9

               ΔL / L% = cte 11%

c) 2d and 2L value

               ΔL = (cte L / d ½ )/ 2L

               ΔL/L% = cte 100/4

               ΔL/L% = cte 25%

d) value 4d and L

               ΔL = cte L / d² 1/16

                ΔL/L % = cte 100/16

                ΔL/L % = cte 6.25%

The highest percentage of change corresponds to the thinnest rod, the correct answer is a

Answer:

[tex]f=1.13s^{-1}=1.13Hz[/tex]

Explanation:

Hello,

In this case, a frequency stands for a rate in which some action is done per unit of time. In this case, for the heartbeat, since 68 actions (heartbeats) occur in 1.0, the frequency turns out:

[tex]f=\frac{68}{1.0min}=68min^{-1}[/tex]

Or as most commonly used in Hz ([tex]s^{-1}[/tex]):

[tex]f=68\frac{1}{min} *\frac{1min}{60s}=1.13s^{-1}=1.13Hz[/tex]

Best regards.

Answer:

4 / 7

Explanation:

1/total resistance = 1/1 + 1/2 + 1/4

= 1¾

total resistance = 1 ÷ 1¾

= 4/7

Answer:

The final temperature is 61.65 °C

Explanation:

mass of copper pot [tex]m_{c}[/tex] = 2 kg

temperature of copper pot [tex]T_{c}[/tex] = 20 °C  (the pot will be in thermal equilibrium with the room)

specific heat capacity of copper [tex]C_{c}[/tex]= 385 J/kg-°C

The heat content of the copper pot = [tex]m_{c}[/tex][tex]C_{c}[/tex][tex]T_{c}[/tex] = 2 x 385 x 20 = 15400 J

mass of boiling water [tex]m_{w}[/tex] = 200 g = 0.2 kg

temperature of boiling water [tex]T_{w}[/tex] = 100 °C

specific heat capacity of water [tex]C_{w}[/tex] = 4182 J/kg-°C

The heat content of the water = [tex]m_{w}[/tex][tex]C_{w}[/tex][tex]T_{w}[/tex] = 0.2 x 4182 x 100 = 83640 J

The total heat content of the water and copper mix [tex]H_{T}[/tex] = 15400 + 83640 = 99040 J

This same heat is evenly distributed between the water and copper mass to achieve thermal equilibrium, therefore we use the equation

[tex]H_{T}[/tex] =   [tex]m_{c}[/tex][tex]C_{c}[/tex][tex]T_{f}[/tex] + [tex]m_{w}[/tex][tex]C_{w}[/tex]

where [tex]T_{f}[/tex] is the final temperature of the water and the copper

substituting values, we have

99040 = (2 x 385 x [tex]T_{f}[/tex]) + (0.2 x 4182 x

99040 = 770[tex]T_{f}[/tex] + 836.4

99040 = 1606.4[tex]T_{f}[/tex]

[tex]T_{f}[/tex] = 99040/1606.4 = 61.65 °C

Answer:

The distance is [tex]D = 2.6 \ m[/tex]

Explanation:

From the question we are told that

    The wavelength of the light is  [tex]\lambda = 476.1 \ nm = 476.1 *10^{-9} \ m[/tex]

      The  distance between the slit is  [tex]d = 0.29 \ mm = 0.29 *10^{-3} \ m[/tex]

       The  between the first and second dark fringes is  [tex]y = 4.2 \ mm = 4.2 *10^{-3} \ m[/tex]

Generally  fringe width is mathematically represented as

       [tex]y = \frac{\lambda * D }{d}[/tex]

Where D is the distance of the slit to the screen

   Hence

        [tex]D = \frac{y * d}{\lambda }[/tex]

substituting values

       [tex]D = \frac{ 4.2 *10^{-3} * 0.29 *10^{-3}}{ 476.1 *10^{-9} }[/tex]

        [tex]D = 2.6 \ m[/tex]

Answer:

[tex]r=4.24\times 10^{11}\ m[/tex]

Explanation:

Given that,

Orbital time period, T = 3.75 earth years

Mass of star, [tex]m=3.23\times 10^{30}\ kg[/tex]

We need to find the radius of the exoplanet's orbit. It is a concept of Kepler's third law of motion i.e.

[tex]T^2=\dfrac{4\pi^2}{GM}r^3[/tex]

r is the radius of the exoplanet's orbit.

Solving for r we get :

[tex]r=(\dfrac{T^2GM}{4\pi^2})^{1/3}[/tex]

We know that, [tex]1\ \text{earth year}=3.154\times 10^7\ \text{s}[/tex]

So,

[tex]r=(\dfrac{(3.75\times 3.154\times 10^7)^2\times 6.67\times 10^{-11}\times 3.23\times 10^{30}}{4\pi^2})^{1/3}\\\\r=4.24\times 10^{11}\ m[/tex]

So, the radius of the exoplanet's orbit is [tex]4.24\times 10^{11}\ m[/tex].

Answer:

1. e m fmax = 0.00598 Volt

2. Imax = 0.000854 Amp

Explanation:

1. Find the maximum induced emf.

e m fmax =

Given that e m fmax = N*A*B*w

N = 1

A = 2 cm^2 = 0.0002 m^2

f = 143 rotation per minute = 143/min

f = (143/min) * (1 min/60 sec) = 2.38/sec

w = 2Πf = 2 * Π * 2.38 = 14.95 rad/sec

B = 2T

e m fmax = N*A*B*w

e m fmax = 1 * 0.0002 * 2 * 14.95

e m fmax = 0.00598 Volt.

2. Find the maximum current through the bulb.

Imax = e m fmax / R

Where R is the total resistance in the circuit is 7 Ω.

Imax = 0.00598/7 = 0.000854 Amp.

Imax = 0.000854 Amp

1) The maximum induced EMF in the loop of wire is; EMF_max = 9.52 × 10^(-4) V

2) The maximum current through the bulb is;

I_max = 1.36 × 10^(-4) A

We are given;

Number of turns; N = 1

Magnitude of magnetic field; B = 2 T

Area; A = 2 cm² = 0.0002 m²

Angular frequency; ω = 143 /min = 2.38 /s

Resistance; R = 7 Ω.

1) Formula for maximum induced EMF is;

EMF_max = NAωB

Plugging in the relevant values gives;

EMF_max = 1 × 0.0002 × 2.38 × 2

EMF_max = 9.52 × 10^(-4) V

2) Formula for maximum current through the bulb is given as;

I_max = EMF_max/R

Plugging in the relevant values;

I_max = (9.52 × 10^(-4))/7

I_max = 1.36 × 10^(-4) A

Read more at; https://brainly.com/question/24487261

Answer:

292 nm

Explanation:

The work function of gallium ∅ = 94.25 eV = 6.81 x 10^-19 J

at maximum wavelength, the energy of the photons is equal to its work function

Energy of the electron = hf

but hf = hc/λ

where h is the planck's constant = 6.63 × 10-34 m^2 kg/s

c is the speed of light = 3 x 10^8 m/s

λ is the wavelength that this occurs, which is the maximum wavelength

Equating, we have

hc/λ =  ∅

substituting, we have

(6.63 × 10-34 x 3 x 10^8)/λ = 6.81 x 10^-19

(1.989 x 10^-25)/(6.81 x 10^-19) = λ

λ = 292.07 x 10^-9 = 292 nm

Answer:

The potential will be Va/b

Explanation:

So Let sphere A charged Q to potential V.

so, V= KQ/a. ....(1

Thus, spherical shell B is connected to the sphere A by a wire, so all charge always reside on the outer surface.

therefore, potential will be ,

V ′ = KQ/b = Va/b... That is from .....(1), KQ=Va]

Answer:

A) y = 3.56 mm

B) y = 3.56 mm

Explanation:

A) The distance from the central maximum to the first bright region can be found using Young's double-slit equation:

[tex] y = \frac{m\lambda L}{d} [/tex]

Where:

λ: is the wavelength = 546.1 nm

m: is first bright region = 1

L: is the distance between the screen and the plane of the parallel slits = 1.50 m

d: is the separation between the slits = 0.230 mm

[tex] y = \frac{m\lambda L}{d} = \frac{1*546.1 \cdot 10^{-9} m*1.50 m}{0.230 \cdot 10^{-3} m} = 3.56 \cdot 10^{-3} m [/tex]  

B) The distance between the first and second dark bands is:

[tex] \Delta y = \frac{\Delta m*\lambda L}{d} [/tex]

Where:

[tex] \Delta m = m_{2} - m_{1} = 2 - 1 = 1 [/tex]

[tex] \Delta y = \frac{1*546.1 \cdot 10^{-9} m*1.50 m}{0.230 \cdot 10^{-3} m} = 3.56 \cdot 10^{-3} m [/tex]      

I hope it helps you!

Answer:

The induced current in the resistor is I = BLv/R

Explanation:

The induced emf ε in the long bar of length, L in a magnetic field of strength, B moving with a velocity, v is given by

ε = BLv.

Now, the current I in the resistor is given by

I = ε/R where ε = induced emf in circuit and R = resistance of resistor.

So, the current I = ε/R.

substituting the value of ε the induced emf, we have

I = ε/R

I = BLv/R

So, the induced current through the resistor is given by I = BLv/R

Answer:

-50N

Explanation:

F=ma=m(Vf-Vi)/t

F=(10)(-10)/(2)=-50N

So the force acting on the block is -50N, where the negative sign simply tells us that the force is opposite to the direction of movement.

Element is

[tex]\boxed{\sf {}^{27}Al_{13}}[/tex]

[tex]\\ \sf\longmapsto No\:of\:Protons=Atomic \:Number=13[/tex]

[tex]\\ \sf\longmapsto No\:of\:Neutrons=Mass\:number-Atomic\:Number[/tex]

[tex]\\ \sf\longmapsto No\:of\:Neutrons=27-13[/tex]

[tex]\\ \sf\longmapsto No\:of\:Neutrons=14[/tex]

And

[tex]\\ \sf\longmapsto No\:of\:electrons=No\:of\:Protons=13[/tex]

Answer:

Acceleration of the body is:

[tex]a=0.27\,\,m/s^2[/tex]

Explanation:

Use Newton's second Law to solve for the acceleration:

[tex]F=m\,\,a\\a=\frac{F}{m} \\a=\frac{4\,N}{15\,\,kg} \\a=0.27\,\,m/s^2[/tex]

Answer:

Option (c) : 20°C

Explanation:

[tex]t(final) = \frac{w1 \times t1 + w2 \times t2}{w1 + w2} [/tex]

T(final) = 500* 10 + 100*70/600 = 20°C

Answer:

7066kg/m³

Explanation:

The forces in these cases (air and water) are: Fa =mg =ρbVg Fw =(ρb −ρw)Vg where ρw = 1000 kg/m3 is density of water and ρb is density of the block and V is its density. We can find it from this two equations:

Fa /Fw = ρb / (ρb −ρw) ρb = ρw (Fa /Fa −Fw) =1000·(1* 21.2 /21.2 − 18.2)

= 7066kg/m³

Explanation:

Answer:

The volume of the block is 306 cm³

The density of the block is 7.07 g/cm³

Explanation:

Given;

weight of block in air, [tex]W_a[/tex] = 21.2 N

Weight of block in water, [tex]W_w[/tex] = 18.2 N

Mass of the block in air;

[tex]W_a = mg[/tex]

21.2 = m x 9.8

m = 21.2 / 9.8

m = 2.163 kg

mass of the block in water;

[tex]W_w = mg[/tex]

18.2 = m x 9.8

m = 18.2 / 9.8

m = 1.857 kg

Apply Archimedes principle

Mass of object in air  - mass of object in water = density of water   x  volume                  of object

2.163 kg - 1.857 kg = 1000 kg/m³ x Volume of block

0.306 kg = 1000 kg/m³ x Volume of block

Volume of the block = [tex]\frac{0.306 \ kg}{1000 \ kg/m^3}[/tex]

Volume of the block = 3.06 x 10⁻⁴ m³

Volume of the block = 306 cm³

Determine the density of the block

[tex]Density = \frac{mass}{volume} \\\\Density =\frac{2163 \ g}{306 \ cm^3} \\\\Density = 7.07 \ g/cm^3[/tex]

Answer:

The maximum force that can be lifted by this system is  51,478.4 kg

Explanation:

Given;

maximum gauge pressure of the hydraulic system, Hp = 15 atm = 1.52 x 10⁶ N/m²

diameter of the piston, d = 65 cm = 0.65 m

The maximum gauge pressure of the piston is given as;

[tex]Hp = \frac{F}{A}[/tex]

Where;

F is the maximum force of the piston

A is the area of the piston

[tex]A = \pi (\frac{0.65}{2} )^2\\\\A = 0.3319 \ m^2[/tex]

F = Hp x A

F = 1.52 x 10⁶N/m² x 0.3319m²

F = 504488 N

Force is given as;

F = mg

m = F/g

m = 504488/9.8

m = 51,478.4 kg

Therefore, the maximum force that can be lifted by this system is  51,478.4 kg

Answer:

D newton third law

Explanation:

good luck

Answer:

The direction of the force will be towards the east

Explanation:

From the question we are told that  

    The direction of the  downward

Generally according to Fleming's right-hand rule(

          Thumb -  direction of force

           Middle finger -  direction of current

           Index finger -  direction of the magnetic field

) and the fact that the earth magnetic field acts  from south to north with respect to the four cardinal points then the direction of the  force will be toward the east with respect to the four cardinal point on the earth