P=3000W
f1=0.9
f2=0.5
A=15mm2
travel speed=?

Answer:

Explanation:

The lights on your vehicle must be turned on at any time, day or night, when persons and vehicles cannot be clearly seen for 1000 feet.

A vehicle is a piece of equipment, typically with wheels and an engine, used for land-based transportation of people or goods. Cars, buses, and trucks are examples of road vehicles. Farm vehicles include tractors.

Vehicle type refers to a group of power-driven vehicles that share all crucial aspects of their engines, cars, and OBD systems.

When a vehicle is 500 feet away, the driver must dim his headlights.

Avoid looking directly into the light when a car is coming at you; instead, slow down. At least 30 minutes before dusk, headlights must be activated. It is also important to keep in mind that a lower headlight beam improves the driver's ability to see in fog.

Thus, it should be 1000 feet distance.

For more details regarding vehicles, visit:

https://brainly.com/question/29491014

#SPJ2

Based on the positive-going zero crossing at 0° of the sine wave, the instantaneous value at 15° is 7.321V.

At 15°, the instantaneous value is:

= 20√2 x Sin(angle)

Solving gives:

=  20√2 x Sin(15°)

= 7.321V

At angel 33°, the instantaneous value is:

=  20√2 x Sin(angle)

=  20√2 x Sin(33)

= 15.405V

At angle 70°:

=  20√2 x Sin(angle)

=  20√2 x Sin(70)

= 26.579V

The full question is:

A certain sine wave has a positive-going zero crossing at 0° and an rms value of 20 V. Calculate its instantaneous value at each of the following angles: a. 15° b. 33° c. 70°

Find out more on sine wave at https://brainly.com/question/14379001

#SPJ1

An expression for the voltage drop between inverter and PUC

[tex]V D \rightarrow \frac{I(\Omega / k f t) d}{2770}$[/tex]

This is further explained below.

Generally, the equation for Voltage drop is  mathematically given as

[tex]V=\frac{I R}{V}[/tex]

Therefore

[tex]\%$ Voltage drop $=\frac{I R}{V} * 100\\\\$\rightarrow \frac{100 I(\Omega / 15 f t) d}{1000 V_{p}}\\\\$V_{P}=277 \mathrm{~V}$[/tex]

[tex]V D=\frac{I(\Omega / \mathrm{kft}) d}{10 * 2770} \rightarrow \frac{I(\Omega / \mathrm{kft}) d}{2770} \mathrm{~V}\\\\$\% V D \rightarrow \frac{I(\Omega / k f t) d}{2770}$[/tex]

In conclusion, the expression for the voltage drop between inverter and PUC

[tex]V D \rightarrow \frac{I(\Omega / k f t) d}{2770}$[/tex]

CQ

An inverter has a balanced 3-phase, 277/480 V output and is installed a distance, d, ft from the point of utility connection. The DC/AC converter is shown below in the inverter. And the distance d is the physical separation between this DC/AC converter and the PCC.

Derive an expression for the voltage drop between inverter and PUC in terms of d using the basic equation %VD =100IR/V.

Read more about voltage drop

https://brainly.com/question/13094809

#SPJ1

Water pressure principles is known to  state that the amount of Fluid pressure is said to be perpendicular to the surface on which it it exert or works on.

Note that  principle is shown by a vessel that is said to be having flat sides and has water. The pressure exerted by the weight of the water is therefore known to be perpendicular to the walls of the storage.

A water butt is known to be a container that is made and also used to store a lot of rainwater.

Note that Water pressure principles is known to  state that the amount of Fluid pressure is said to be perpendicular to the surface on which it it exert or works on.

Learn more about Water pressure principles  from

https://brainly.com/question/14813457

#SPJ1

When converting liquid-level units to sensor output signal units, you should first convert the liquid-level units to engineering units.

The engineering units are the actual physical measurements of the liquid level, such as meters, feet, inches, or any other relevant unit of length or depth.

Once the liquid level is expressed in engineering units, you can then proceed with the conversion to the sensor output signal units, which typically involves scaling the engineering units to match the range and sensitivity of the sensor's output.

This ensures that the sensor provides an accurate and meaningful representation of the liquid level, making it easier to interpret and use the data for various applications.

Know more about engineering units:

https://brainly.com/question/33553485

#SPJ7

The capacitance is affected is that the capacitance increases because of the insertion of Teflon.

A `is known to be a form of a device that is said to be used to save some amount of charges in any electrical circuit.

Note that the capacitor functions on the principle that the capacitance of a conductor is said to increases if an earthed conductor is  taken close to it.

Hence, The capacitance is affected is that the capacitance increases because of the insertion of Teflon.

See full question below

A dielectric material, such as Teflon®, is placed between the plates of a parallel-plate capacitor without altering the structure of the capacitor. The charge on the capacitor is held fixed. How is the electric field between the plates of the capacitor affected?

The electric field is not altered, because the structure remains unchanged.

The electric field becomes zero after the insertion of the Teflon®.

The electric field decreases because of the insertion of the Teflon®.

The electric field becomes infinite because of the insertion of the Teflon®.

The electric field increases because of the insertion of the Teflon®.

Learn more about  electric field  from

https://brainly.com/question/14781269

#SPJ1

Based on the calculations, Vivian's Violins net operating income is equal to: D. $99,000.

Mathematically, the net operating income of an individual or business firm can be calculated by using this formula:

Net operating income = Contribution margin - Total fixed costs

Given the following data:

Substituting the given parameters into the formula, we have;

Net operating income = $184,000 - $85,000

Net operating income = $99,000.

Read more on net operating income here: https://brainly.com/question/24165947

#SPJ1

Answer:

the carburizing time necessary to achieve a carbon concentration is 31.657 hours

Explanation:

Given the data in the question;

To determine the carburizing time necessary to achieve the given carbon concentration, we will be using the following equation:

(Cs - Cx) / (Cs - C0) = ERF( x / 2√Dt)

where Cs is Concentration of carbon at surface = 0.90

Cx is Concentration of carbon at distance x = 0.30 ; x in this case is 4 mm = ( 0.004 m )

C0 is Initial concentration of carbon = 0.10

ERF() = Error function at the given value

D = Diffusion of Carbon into steel

t = Time necessary to achieve given carbon concentration ,

so

(Cs - Cx) / (Cs - C0) = (0.9 - 0.3) / (0.9 - 0.1)

= 0.6 / 0.8

= 0.75

now, ERF(z) = 0.75; using ERF table, we can say;

Z ~ 0.81; which means ( x / 2√Dt) = 0.81

Now, Using the table of diffusion data

D = 5.35 × 10⁻¹¹ m²/sec at (1100°C) or 1373 K

now we calculate the carbonizing time by using the following equation;

z = (x/2√Dt)

t is carbonizing time

so we we substitute in our values

0.81 = ( 0.004 / 2 × √5.35 × 10⁻¹¹ × √t)

0.81 = 0.004 / 1.4628 × 10⁻⁵ × √t

0.81 × 1.4628 × 10⁻⁵ × √t = 0.004

1.184868 × 10⁻⁵ × √t = 0.004  

√t = 0.004 / 1.184868 × 10⁻⁵

√t = 337.5903

t = ( 337.5903)²  

t = 113967.21 seconds

we convert to hours

t = 113967.21 / 3600

t = 31.657 hours

Therefore, the carburizing time necessary to achieve a carbon concentration is 31.657 hours

A broken yellow line on the pavement tells that the adjacent lane is traveling in the opposite direction and passing is permitted.

A broken white line on the pavement show that the adjacent lane is traveling in the same direction and passing is permitted.

Pavement markings are known to be tools that are used to pass infor or messages to roadway users.

Note  that they tell the part of the road that one need to use, give information about conditions ahead, and others

Note that A broken yellow line on the pavement tells that the adjacent lane is traveling in the opposite direction and passing is permitted.

Learn more about pavement markings from

https://brainly.com/question/10179521

#SPJ1

Answer:

Metal wireways are sheet metal "U"s with removable housing for protecting electrical equipment, wires, and cables.

Explanation:

These are especially used to run wire in manufacturing environments.

The net radiation heat transfer between the two plates per unit surface area of the plates with shield and without shied are respectively; 2282.76 W/m² and 9766.75 W/m²

We are given;

Temperature 1; T₁

Temperature 2; T₂

Temperature 3; T₃

Emissivity 1; ε₁ = 0.3

Emissivity 2; ε₂ = 0.7

Emissivity 3; ε₃ = 0.2

The net rate of radiation heat transfer with a thin aluminum shield per unit area of the plates with shield is;

Q'₁₂ = σ(T₁⁴ - T₂⁴)]/[((1/ε₁) + (1/ε₂) - 1) + ((1/ε₃,₁) + (1/ε₃,₂) - 1)]

Q'₁₂ = 5.67 * 10⁻⁸(900⁴ - 300⁴)/[((1/0.3) + (1/0.7) - 1) + ((1/0.15) + (1/0.15) - 1)]

Q'₁₂,shield = 2282.76 W/m²

The net rate of radiation heat transfer with a thin aluminum shield per unit area of the plates with no shield is;

Q'₁₂,no shield = σ(T₁⁴ - T₂⁴)]/((1/ε₁) + (1/ε₂) - 1))

Q'₁₂,no shield = 5.67 * 10⁻⁸(900⁴ - 300⁴)/[(1/0.3) + (1/0.7) - 1)]

Q'₁₂,no shield = 9766.75 W/m²

Then the ratio of radiation heat transfer for the two cases becomes;

Q'₁₂,shield/Q'₁₂,no shield = 2282.76/9766.75 = 0.2337 or 4/17

Read more about Net Radiation Heat Transfer at; https://brainly.com/question/14148915

#SPJ1

Answer:

The wheel will go through 1146 revolutions in 5 minutes.

Explanation:

We can the formula:

[tex]\boxed{\omega = \frac{2 \pi}{T}}[/tex]

where

ω ⇒ angular speed (24 rad/s),

T ⇒ time period (? s),

and solve for T to find the time it takes for the wheel to complete one revolution.

⇒  [tex]24 = \frac{2 \pi}{T}[/tex]

⇒  [tex]T = \bf \frac{2 \pi}{24}[/tex]  s

This means it takes [tex]\bf \frac{2 \pi}{24}[/tex] seconds for the wheel to complete one revolution.

Now, using the unitary method,

In [tex]\frac{2 \pi}{24}[/tex] seconds          ⇒    1 revolution completed

In 1 second              ⇒    1 ÷ [tex]\frac{2 \pi}{24}[/tex]   =  [tex]\frac{24}{2 \pi}[/tex]  revolutions completed

In (5 × 60 = ) 300s  ⇒     [tex]\frac{24}{2 \pi}[/tex]   ×  300   = 1145.9

                                                            ≅ 1146 revolutions completed

The section(s) of the Code emphasize that all circuiting must be done so as to avoid the damaging effects of induction heating is 300.35, 300.3(B), and 300.20(A).

The term induction heating is known to be a form of heating of material that occurs via an electric current that makes a flow via the material or its container through the means of electromagnetic induction.

Hence, The section(s) of the Code emphasize that all circuiting must be done so as to avoid the damaging effects of induction heating is 300.35, 300.3(B), and 300.20(A).

Learn more about heating from

https://brainly.com/question/13982702

#SPJ1

An example of a power consuming device would be a(n) light bulb, a computer device while an example of a non-power consuming device would be a(n) switch or button.

The quantity of energy utilized per unit of time is known as power consumption. Power use is a significant factor in digital systems.

Power consumption is a limiting factor for the battery life of portable devices like laptop computers and cell phones.

Learn more about power consumption:
https://brainly.com/question/14860418
#SPJ1

Sales represent the income statement item used in verticla analyses in order to determine the cost contribution for each expense category (Option C).

In business, a vertical analysis represents a methodology used to examine financial statements that are ordered as specific points.

A vertical analysis analyzes numbers for only one period, conversely to the horizontal analyses that generally involve many different periods.

In conclusion, sales represent the income statement item used in verticla analyses in order to determine the cost contribution for each expense category (Option C).

Learn more about the vertical analysis here:

https://brainly.com/question/23963688

#SPJ1

if two 1.5 ya alt batteries are connected to head to the tail the voltage is 3.0 volt it is the because the battery is insidious reduce a voltage equal to number of battery is multiplied by the voltage of individual

The first step that is needed in order to shift the reverse would be to Push down on the shift lever.

This is the term that is used in driving to explain the scenario that occurs due to the fact that a person has to go through a system of changing gears while they are driving. An example of how this is used is when a person says that there car has a manual transmission instead of automatic transmission.

This would mean that this person would be the one that would be changing the gears while driving on their own. To do this what would be done is to Push down on the shift lever.

Read more on driving here: https://brainly.com/question/1557131

#SPJ1

Answer: Increase in minimills

Explanation:

Maximum absolute values of the shear = 28 KN

Maximum absolute values of bending moment = 5.7 KN.m

A) We can see the beam loaded in the first image attached.

For the shear diagram, let us calculate the shear from point load to point load.

From A to C, summing vertical to zero gives; ∑fy = 0: -20 - V = 0

V = -20 KN

From C to D, summing vertical to zero gives; ∑fy = 0: -20 + 48 - V = 0

V = 28 KN

From D to E, summing vertical to zero gives; ∑fy = 0: -20 + 48 - 20 - V = 0

V = 8 KN

From E to B, summing vertical to zero gives; ∑fy = 0: -20 + 48 - 20 - 20 - V = 0

V = -12 KN

For the bending moment diagram, let us calculate the bending moment from point load to point load.

At point A, the bending moment would be zero. Thus, M_A = 0 KN.m

At point C, taking moment about point C and equating to zero gives;

M_C = 0. Thus; 20(0.225) + M = 0

M = -4.5 KN.m

At point D, taking moment about point D and equating to zero gives;

M_D = 0. Thus; 20(0.525) - 48(0.3) + M = 0

M = 3.9 KN.m

At point E, taking moment about point E and equating to zero gives;

M_D = 0. Thus; 20(0.75) - 48(0.525) + 20(0.225) + M = 0

M = 5.7 KN.m

At point B, taking moment about point E and equating to zero gives;

M_E = 0. Thus; 20(1.05) - 48(0.825) + 20(0.525) + (20 * 0.3) + M = 0

M = 2.1 KN.m

2) From the attached diagrams, we can deduce that;

Maximum absolute values of the shear = 28 KN

Maximum absolute values of bending moment = 5.7 KN.m

Read more about shear force & bending moment diagram at; https://brainly.com/question/14834487

#SPJ1

When a system is in a deep vacuum, never energize the compressor. The correct option is a.

A deep vacuum is a system in which the boiling point of liquid lowers down and the temperature lowers for outgassing. They help in freeze drying, metallurgy, distillation, etc. It used 500 or less than 500 microns for deep vacuum.

Vacuum tubes, such as cathode ray tubes, and electron microscopes are made possible by the electronic resistivity of the vacuum. Torr is the unit used to measure vacuums.

Thus, the correct option is a. never energize the compressor.

To learn more about deep vacuum, refer to the below link:

https://brainly.com/question/17465345

#SPJ1

Using the knowledge in computational language in C++ it is possible to write the code being write a class having two private variables

#include <iostream>

using namespace std;

class Rectangle { /*create a class named Rectangle*/

  private:

  float l,b; /*this class has two private variables l and b*/

  public:

  float getArea(float l, float b) /*this class has one member-function getArea which returns the area of the rectangle*/

  {

   return l*b; /*return the area of the rectangle*/

  }

};

int main () { /*the main function to check the working of our Rectangle class*/

 float l,b;

 Rectangle r1; /*create an object r1 of Rectangle class*/

 cout<<"Enter the length of the rectangle: ";

 cin>>l; /*input the length of the rectangle from the user*/

 cout<<"Enter the breadth of the rectangle: ";

 cin>>b; /*input the breadth of the rectangle from the user*/

 cout <<"Area of the rectangle is: "<< r1.getArea(l,b)<<" square units."; /*find the area of the rectangle using the member function of the class*/

 return 0;

}

See more about C++ at brainly.com/question/19705654

#SPJ1

In regards to high-wind installations, if an old composition asphalt shingle roof is going to be replaced, the roofing contractor should remove the existing shingles and underlayment.

High Wind is known to be a newly created installation techniques that is often used in the installation of offshore wind turbines and this is often done at  higher wind speeds.

Note that, In regards to high-wind installations, if an old composition asphalt shingle roof is going to be replaced, the roofing contractor should remove the existing shingles and underlayment.

Learn more about installations from

https://brainly.com/question/13093522

#SPJ1

Answer:

The reference line helps you achieve the precise connection of Walls for clean intersections.

Explanation:

Reference Lines allow you to place lines on the plot at specific locations to mark important values. You could use these to mark control limits or to indicate a trend line for a set of data.

Answer:

An isolation transformer whose main purpose is to reduce voltage spikes will have a turns ratio of 1 to 1.

This is due to the windings input and output having the same waveform and amplitude.

"1/2" is the right response to this question. Approximately half of the governor gear in vertical crankshaft engines that have a slinger or governor gear and the correct amount of oil in the crankcase is placed above the oiled surface. Draining the oil from the top oil fill tube, as well as the fuel tank and the engine, should be done when the governor gear is about halfway through its rotation.

This is further explained below.

Generally, Engine connecting rods are joined to the crankshaft through the crank mechanism, which is made up of many rotating parts, including the crankshaft, the crankpins, and the crankshaft gears.

In conclusion, "1/2" is the right answer. About half of the governor gear is visible above the oil surface in vertical crankshaft engines with a slinger or governor gear. In order to drain the oil from the top oil fill tube, both the fuel tank and the engine should be at about half of the governor gear after it is completed.

Read more about crankshaft

https://brainly.com/question/9782058

#SPJ1

Structural Safety Assessment and Traffic Control Strategies of Widened Highway Bridges under Maintenance Works Requiring Partial Lane Closure journal is based on the  way and techniques that can be used in maintaining  the Safety on the road as well as the Assessment of Traffic Control.

There are Devices that are typically used in the traffic control, and this can  include speed bumps as well as the barricades to block streets.

Others techniques are:

Traffic restraint can also entails the includes programs  that can foster bicycle as well as the pedestrian travel.

The rapid structural safety assessment help in inspecting and evaluating the concrete structure as well in determining  the damaged structure if it is  unsafe for personnel within the building .

Learn more about Traffic Control at:

https://brainly.com/question/26052026

#SPJ1

Answer:

Unit testing is a software development process in which the smallest testable parts of an application, called units, are individually and independently scrutinized for proper operation. This testing methodology is done during the development process by the software developers and sometimes QA staff. The main objective of unit testing is to isolate written code to test and determine if it works as intended.

Unit testing is an important step in the development process, because if done correctly, it can help detect early flaws in code which may be more difficult to find in later testing stages.

Unit testing is a component of test-driven development (TDD), a pragmatic methodology that takes a meticulous approach to building a product by means of continual testing and revision. This testing method is also the first level of software testing, which is performed before other testing methods such as integration testing. Unit tests are typically isolated to ensure a unit does not rely on any external code or functions. Testing can be done manually but is often automated. It might be helpful