According to Technician A, fuel pump modules are spring-loaded so they can be compressed to fit the aperture.
Electric fuel pumps are often mounted in the fuel tank to utilize the fuel in the tank to cool the pump and ensure a steady supply of fuel. Each injector has a spring-loaded valve that is kept closed by the force of the spring. The valve doesn't open until fuel is squirted into it. The fuel pump driver module controls the voltage supplied to the fuel pump in a vehicle. By adjusting voltage, the module ensures ideal fuel pressure and flow to the engine throughout its entire operating range.
Learn more about voltage here-
https://brainly.com/question/29445057
#SPJ4
fairings are attached to the front and back of a cylindrical body to make it look more streamlined. what is the effect of this modification on the (a) friction drag, (b) pressure drag, and (c) total drag? assume the reynolds number is high enough so that the flow is turbulent for both cases.
The correct answer is (a) friction drag . therefore the correct option is the option (b).
Friction drag, also referred to as skin friction drag, is resistance felt by an object traveling through a fluid as it comes into contact with its surface. It grows with the square of the velocity and is exactly proportional to the area of the surface in contact with the fluid. For connected flows (where there is no separation), frictional drag is significant and is correlated with the exposed surface area. For separated flows, pressure drag is crucial, because it is correlated with the body's cross-sectional area. The air blowing directly above the Earth experiences frictional drag.
To learn more about friction drag click the link below:
brainly.com/question/1389727
#SPJ4
an engineer has performed an experiment to study the effect of four factors on the surface roughness of a machined part. the factors are: a
the correct answer is the option (b).
Surface roughness is the measurement of the relative smoothness of a surface’s profile, calculated via the microscopic deviations in a surface's true form. The larger the deviation from its true form, the rougher the surface, whilst the smaller the deviation, the smoother the surface.A rougher finish cannot be achieved through machining. A secondary process like bead-blasting or tumbling is required. There is no one way to achieve a particular surface roughness as both the machining process and secondary finishing influence the surface roughness. Get in touch with a member of our team to discuss the optimal procedure for finishing your parts.
to learn more about surface roughness click the link below given:
brainly.com/question/27805243
What polymer is a package made of?
Answer:
polyethylene
Explanation:
The elasticity of polyethylene makes it an ideal material for food packaging. Polyethylene is used extensively in the automotive industry. Polyethylene is often used for manufacturing stock poly bags, zip lock bags, bottles, food containers, food crates, stretch film, tape, pallets and plastic sheeting.
Polythene is commonly used as a packaging material. The most common polyethylene types used in food packaging are high-density polyethylene (HDPE), low-density polyethylene (LDPE), and linear low-density polyethylene (LLDPE).
Explanation:One of the most popular materials used in the food industry for packaging is petroleum plastics (synthetic polymers). Such polymers include polyethylene terephthalate (PET), low and high-density polyethylene (LDPE and HDPE respectively), polypropylene (PP), polyvinyl chloride (PVC), and polystyrene (PS). Paper, paperboard, and cardboard cartons are frequently used as packaging for products in stores as well as used in shipping. Corrugated cardboard, for example, has excellent structural stability for shipping, storing, and even marketing products.
part b - designing and analyzing a series rl low-pass filter using the available 130 h inductor, what is the value of the resistor needed to make a low-pass filter with a cutoff frequency of 18 hz ? express your answer to three significant figures and include appropriate units. g
When built, an RL circuit functions as a low pass filter. The resistor is the shunt component in the circuit, and the inductor is the series component.
The inductors' reaction to a rise in operating frequency is what causes the circuit's filtering operation. The frequency at which the output (load) voltage is equal to 70.7% of the input (source) voltage is known as the cutoff frequency for a low-pass filter. An audio signal processor called a low-pass filter (LPF) takes out undesired frequencies from a signal that are above a preset cutoff frequency. It allows the low-end to flow through, ideally unchanged, while gradually filtering out (attenuating) the high-end over the cutoff frequency.
Learn more about voltage here-
https://brainly.com/question/28632127
#SPJ4
Salt in crude oil must be removed before the oil undergoes processing in a refinery. The crude oil is fed to a washing unit where freshwater fed to the unit mixes with the oil and dissolves a portion of the salt contained in the oil. The oil (containing some salt but no water), being less dense than the water, can be removed at the top of the washer. If the “spent” wash water contains 15% salt and the crude oil contains 5% salt, determine the concentration of salt in the “washed” oil product if the ratio of crud oil (with salt) to water used is 4:1.
Answer:
What is the question?
Explanation:
A alloy bar 1m long and 200m in cross-section is subjected to compression force 20KN if the modulus of elasticity of the axial is 100Gpa. Find the decrease in length of the bar
A alloy bar 1m long and 200m in cross-section is subjected to compression force 20KN if the modulus of elasticity of the axial is 100Gpa. The decrease in the length of the bar is 1 X 10^-12m.
Define elasticity.
Elasticity, in physics and materials science, is the capacity of a body to withstand a force that distorts it and to recover its original size and shape when the force is withdrawn.
Elasticity is characterized as a feature of materials that allows them to resume their original shape after being deformed by stress that has been removed. The pascal is the SI unit for elasticity and the elastic modulus (Pa).
Solution Explained:
Given,
Length = 1m
Area of Cross-Section (A) = 200m^2
Tensile force (P) = 20kN
Modulus of elasticity (E) = 100Gpa = 1 X 10^11 N/m^2
Using the formula,
Δl = P X length / A X E
= 20 X 1 / 200 X 1 X 10^11
After calculation, we get
Δl = 1 X 10^-12m
Therefore, the decrease in length is 1 X 10^-12m.
To learn more about elasticity, use the link given
https://brainly.com/question/20067125
#SPJ1
technician a says that dynamic voltage is the voltage (usually of a battery) that exists without a load being applied. technician b says that open circuit voltage (ocv) is the voltage of the power source (battery) with the circuit in operation. who is right?
The battery electrolyte's specific gravity can be used to test the status of charge of a battery cell in the most precise and direct manner possible.
The state of charge increases with the specific gravity of the electrolyte. Voltage is the difference in electric potential between a battery's two terminals. The unit of measurement for voltage is called a volt (V), after the battery's creator, John Volta. An electronic tool called a state-of-charge battery tester is made to check the life and rechargability of an electric battery. A battery's current charging status and voltage output can be provided by a state-of-charge tester, which can also look for any defects that might impair the battery's overall performance.
Learn more about battery here-
https://brainly.com/question/17377812
#SPJ4
ase 8. while discussing the causes of a rich air-fuel ratio: technician a says that a rich air-fuel ratio may be caused by low fuel pump pressure. technician b says that a rich air-fuel ratio may be caused by a defective coolant temperature sensor. who is correct?
Answer:
technician
Explanation:
A resistor, an inductor, and a capacitor are connected in series to an ac source. What is the phase angle between the voltages of the inductor and capacitor in this rlc circuit?.
The phase angle is 180°.
A resistor, inductor, and capacitor are connected in series to an AC source.
You can learn more through link below:
https://brainly.com/question/16971122#SPJ4
_____ can process many pieces of data at the same time and learn to recognize patterns.
Neural networks can process many pieces of data at the same time and learn to recognize patterns.
However, similar to the brain, such networks are capable of processing a variety of information concurrently, learning to spot patterns, and programming themselves to address similar issues on their own. Single instruction multiple data, or SIMD, is a type of parallel processing where a computer has two or more processors that all follow the same instruction set but handle distinct types of data. Large data sets that are based on the same predefined benchmarks are frequently analyzed using SIMD. Haptic interfaces, which are frequently used in gaming consoles, clothes, and sports training equipment, give tactile feedback by imparting vibrations or pressures to the user using actuators that are embedded in the device (for example, a cell phone).
Learn more about network here-
https://brainly.com/question/13051988
#SPJ4
In conducting a test on the kind of music that may encourage plant growth, what practice upholds the fair test standard? A. using different kinds of plants B. giving some plants more water than others C. exposing the plants to different types of music D. using nutrient-rich soil for one and plain soil for others
In conducting a test on the kind of music that may encourage plant growth, the practice that upholds the fair test standard are:
using different kinds of plants (Option A)giving some plants more water than others (Option B)using nutrient-rich soil for one and plain soil for others (Option D).What are the factors that determine plant growth?Water, light, temperature, and nutrients are the four most important factors influencing plant development.
Plants go through the following stages: seed to sprout, vegetative, budding, blooming and maturing. Similarly, when individuals and plants develop, their dietary requirements alter.
The following are major elements influencing plant growth: Temperature: As the temperature rises, growth accelerates. Light intensity, duration, and quality all have an impact on various physiological processes that occur in plants. Water: Water is necessary for plant development.
Playing classical or jazz music stimulated growth in most plants, but harder metal music generated stress. This might be because the vibrations of metal music are too strong for plants and activate cells excessively. We compare it to massaging your plant with music; they prefer a softer touch.
Learn more about plant growth:
https://brainly.com/question/9323511
#SPJ1
Consider the following expression BNF:
::= + | - |
::= * | / |
::= | ( )
::= 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
Using recursive descent, and only recursive descent, scan expressions that adhere to this BNF
to build their expression tree; write an integer valued function that scans the tree to
evaluate the expression represented by the tree.
There are plenty of clever programs online that you can download to evaluate arithmetic
expression tree; if you want zero in this assignment, download one and submit it as
programming assignment #2; if you want a grade greater than zero, please follow our
instructions. Thanks.
Input:
• A numeric expression adhering to this BNF.
Output:
• Some representation of the expression tree.
• The result of evaluating the expression.
The program will be:
import java.io.IOException;
import java.util.Scanner;
/* This class represents a Node in Expression Tree that will contain a digit(symbol) and will have links to its
* left and right childs, which would be recursively having its own left and right sub childs accordingly
*/
class Node {
public char data; // Store Node Data
public Node leftChild; // pointer to left sub tree
public Node rightChild;// pointer to right sub tree
// Constructor to initialize Node with data
public Node(char x) {
data = x;
}
// display the Node's data stored
public void displayNode() {
System.out.print(data);
}
}
/* This is Stack class (Stack1) which performs push(), pop(), isEmpty() operation on Node's data */
class Stack1 {
private Node[] a; // Stack of type Node
private int top, m; // top = top of stack variable, m = Maximum Size of the Stack
public Stack1(int max) {
m = max;
a = new Node[m];
top = -1;
}
What is a have program?Java is a popular object-oriented programming language and software platform that powers billions of devices such as notebook computers, mobile devices, gaming consoles, medical devices, and many more.
Java's rules and syntax are based on the C and C++ programming languages. The program is illustrated based on the information.
Learn more about program on:
https://brainly.com/question/26642771
#SPJ1
air flows at 1.2 m/s along a flat surface when it encounters a jet of air issuing from the horizontal wall at point a, as in fio p8.16. the jet volume flow is 0.4 m/s per unit depth into the paper. if the jet is approximated as an inviscid line source, (a) locate the stagnation point s on the wall. (b) how far vertically will the jet flow extend into the stream?
In the upper atmosphere, jet streams are relatively narrow bands of powerful wind. Jet streams carry the winds as they go from west to east
Explain about the jet flow?Jet streams can travel at speeds of more than 275 mph (239 kts / 442 km/h) and range in height from four to eight miles. Both the Northern and Southern Hemispheres have jet streams.
At altitudes of roughly 8 to 15 kilometres, jet streams move across the tropopause, the region between the troposphere and the stratosphere (5 to 9 miles). When cold air and hot air collide, strong air currents are created that, when viewed on a jet stream map, often resemble wavy, striated rivers.
The mid to upper troposphere, the part of the Earth's atmosphere where we live and breathe, is where jet streams are found, about five to nine miles above the planet's surface.
To learn more about jet flow refer to:
https://brainly.com/question/5993570
#SPJ4
the small-signal model is said to be valid for voltage variations of about 5 mv. to what percentage current change does this correspond? (consider both positive and negative signals.) what is the maximum allowable voltage signal (positive or negative
The signal is "high" when it is over the high threshold. Undefined intermediate levels lead to extremely implementation-specific circuit behavior.
It is customary to allow for some tolerance in the voltage levels utilized; for instance, logic 0 might be represented by 0 to 2 volts, and logic 1 by 3 to 5 volts. An example of a widely used signal standard is 0-10 volts, which states that a signal of 0 volts represents 0% of the measurement, a signal of 10 volts represents 100% of the measurement, a signal of 5 volts represents 50% of the measurement, and so on. For a "low" logic state and a "high" logic state, respectively, acceptable input signal voltages range from 0 volts to 0.8 volts and 2 volts to 5 volts. The supply voltage will, for the most part, determine the operating range.
Learn more about voltage here-
https://brainly.com/question/28632127
#SPJ4
a distribution transformer is near a home to convert high voltage from power station to wall outlets. the wall outlets have 120 v rms. the primary to secondary turn ratio in the transformer is 200:1. find the rms power station voltage in kv.
High voltages enable the transmission of power over long distances because, as was previously mentioned, they require less current to transmit a given quantity of power, which reduces line loss.
However, large voltages provide more risks, hence transformers are used to generate lower power close to the user. The primary and secondary coils are the two coils. In typical operation, the input voltage is applied to the primary, and the secondary generates the output voltage after transformation. The primary coil's magnetic field is not only trapped by the iron core, but also strengthened by the core's magnetization. Due to the AC input voltage, the secondary receives a time-varying magnetic flux that induces an AC output voltage.
Learn more about voltage here-
https://brainly.com/question/28632127
#SPJ4
3. When using the Cold Saw what is the correct Water to Coolant ratio?
a.
b.
10:1
20:1
c. 15:1
d. 25:1
When using the cold saw, the correct water-to-coolant ratio should be 20:1.
What is a cold saw?
A cold saw is a sawing machine that uses a circular saw blade to cut metal.
What happens if coolant to water ratio is too high?
Having too much water will not cool the engineHaving too much antifreeze could cause your water pump to fail.What happens if you don't add water to the coolant?
Water has minerals that can deform deposits inside the radiator and the cooling system passages of your engine. And over a long period of time, they can lead to overheating.Therefore, in a cold saw the water-to-coolant ratio should always be 20:1.
To know more about water as a coolant from the given link:
https://brainly.com/question/14624644
#SPJ1
technician a says that loose fan belts are usually destroyed more rapidly than belts that are adjusted too tight. technician b says that too tight adjustment on poly-v fan belts can destroy bearings. who is correct?
The bearings and shaft experience additional loads as a result of this increased tension. Bearings' lifespans might be shortened by excessive stress.
Explain about poly v belt?The inside of the Poly-V Belt, also known as the Ribbed Belt, is lined with longitudinal v-shaped ribs. These ribs give the pulley and the belt a bigger surface area to contact, which increases friction force. Compared to a flat belt or rubber v-belt of the same size, the belt can convey more power as a result.
The Poly-V Belt's design ensures superior protection for all reinforcing cords, resulting in a more even load distribution. The Poly-V Belt also serves as a guide for a belt tensioner or idler pulley. Less space is needed for Poly-V Belt drives, and the Belt can be stretched under higher tension.
To learn more about Poly v belt refer to:
https://brainly.com/question/18368496
#SPJ4
Technician A says that a tapered roller bearing assembly has less rolling resistance than a similarly sized ball bearing assembly. Technician B says that the bearing assembly in a unitised wheel bearing assembly can normally be disassembled, cleaned, and repacked. Who is correct?
Technician A says that a tapered roller bearing assembly has less rolling resistance than a similarly sized ball bearing assembly. Technician B says that the bearing assembly in a unitized wheel bearing assembly can normally be disassembled, cleaned, and repacked. The technician that is correct is Technician B.
What is a Tapered Roller Bearing Assembly?A cup and cone assembly is used in tapered roller bearings. The cup is made up of the outer ring, and the cone assembly is made up of the inner ring, rollers, and cage. This bearing design accommodates combined loads while maintaining minimal friction during operation.
A roller bearing is a cylindrical element that allows a bushing or bearing block to move with little friction.
A ball bearing is a spherical unit with the same purpose as a roller bearing. The real distinction is the contact surface between the bearing and the rail.
Learn more about tapered roller bearing assembly:
https://brainly.com/question/15313541
#SPJ1
a(n) is a support system that is completely concealed in the wall and supports the load of the fixture by means of a suitable face plate and base support firmly anchored to the floor.
Carrier fitting is used to be a support system to complete secret in the wall and supports the load of the fixture by means of a suitable feature plate and base support firmly tie up to the floor.
Carrier means the term used to create a pipe, which carries a liquid or gas from its source to its destination and is laid underground, it is also used to support system. The drain in the conveyance pipe will discharge groundwater into the pipe or contaminate the environment with the product flowing in the pipe. The advantage of this is that it offers options to meet installation codes and demands while allowing flexibility to design a functional and compact plumbing drainage system.
Learn more about carrier fitting at https://brainly.com/question/28119674
#SPJ4
13. The type of building that can be built in an area would be covered in
O A. building permits.
O B. deed restrictions.
O C. sales contracts.
O D. zoning restrictions.
a w18x65 of a992 steel is laying on its side and is being bent about its weak or y-axis. assuming the member is only supported at its ends and is simply supported, what is the maximum span length it can have before it reaches its design moment capacity based on it plastic moment due to its self-weight only? (hint: do not apply a load factor since the self-weight is well-known.)
A framework for a shared understanding of the acceptable standards when contracting for structural steel is provided by the AISC Code of Standard Practice.
What is meant by AISC?The AISC created the American Institute of Steel Construction (AISC), a company-level accreditation for the manufacture and construction of structural steel. Companies that construct steel structures, such as buildings, bridges, and the parts of bridges and highways, are eligible for this certification.IS: 2062 - General Steel Purpose Specifications.AISC Certification looks at a company's QMS as a whole, going much beyond the minimal standards for product inspection. AISC-Certified businesses must have a comprehensive QMS that addresses every aspect of fabrication or erection, from quality objectives to employee development to product delivery.All errata to earlier printings have been incorporated into the most recent version of ANSI/AISC 360-16, which was published in March 2021 (the following errata lists also include updates to other sections of the 15th Edition Steel Construction Manual).To Learn more About AISC Code Refer To:
https://brainly.com/question/21497348
#SPJ4
land subsidence due to overdrawing can cause what to occur? question 19 options: the formation of sinkholes the inability to recharge the aquifer in the future damages to roads, building foundations, and sewer lines all of these choices are correct.
Land subsidence is the gradual or abrupt sinking of the Earth's surface caused by the migration of earth elements underground.
Aquifer-system compaction, drainage of organic soils, underground mining, hydro compaction, natural compaction, sinkholes, are the main causes of land subsidence. The loss of levee freeboard and subsequent reduction in flood protection, the change in gradient along water conveyance canals, damage to roads and bridges, and the collapse of water well casings are some major consequences of land. When a lot of groundwater has been taken out of particular kinds of rocks, like fine-grained sediments happens. The ground is held up in part by the water, which causes the rock to compact. The rocks collapse in on themselves when the water is turned off.
Learn more about protection here-
https://brainly.com/question/28639832
#SPJ4
An example of an external irreversibility associated with the Rankine cycle is
a. expansion of the working fluid through the turbine.
b. frictional effects resulting in pressure drops.
c. combustion of fuel.
d. irreversibilities in the pump.
An example of an external irreversibility associated with the Rankine cycle is combustion of fuel. Option C is correct.
What is the Rankine cycle?The Rankine cycle is defined as a modified thermodynamic cycle that describes how certain heat engines, such as steam turbines or reciprocating steam engines, extract mechanical work from a fluid as it passes between a heat source and a heat sink.
The Rankine cycle, also known as the Rankine Vapor Cycle, is a process that is widely used in power plants such as coal-fired power plants and nuclear reactors. The best example of an external irreversibility associated with the Rankine cycle is combustion of fuel.
Therefore, option C is correct.
Learn more about the Rankine cycle, refer to:
https://brainly.com/question/16836203
#SPJ1
tech a says that duo-servo brake shoes are only anchored on the top. tech b says that duo-servo brake shoe systems typically adjust automatically during normal brake applications in a forward direction. who is correct?
Tech A is correct. Duo-servo Brakes with the Bendix design are simple to recognize. At the top of the backing plate, they feature a single fixed anchor pin, and below the anchor is a dual-piston wheel cylinder.
Two brake shoes, referred to as the primary shoe and secondary shoe, are connected by an adjuster in the duo servo type's mechanism. Strong pressure from the primary shoe's servo effect (self-boosting effect) is transferred to the linked secondary shoe, creating a significant amount of braking force. The disadvantage of a dual servo is that it will use 80% of the braking force in reverse as opposed to a single servo's 20%, which will make it simpler to reverse your trailer.
Learn more about brakes here-
https://brainly.com/question/17205672
#SPJ4
a half-wave rectifier circuit with a 500-q load operates from a 120-v (rms) 60-hz household supply through a 12-to-l step-down transformer. it uses a silicon diode that can be modeled to have a 0.7-v drop for any current. what is the peak voltage of the rectified output? for what fraction of the cycle does the diode conduct? what is the average output voltage? what is the average current in the load?
A sinusoidal waveform's average voltage (VAV) is calculated by multiplying the peak voltage value by the constant 0.637,which is equal to two divided by pi.
Explain about the Average output voltage?A waveform's level that is determined by the requirement that the region enclosed by the curve above it is exactly equal to the region enclosed by the curve below it.
The amount of power averaged throughout time is referred to as average power. By averaging the instantaneous power's time throughout a single cycle, we may determine average power.
By multiplying the peak value by 0.637 or the RMS value by 0.9, average or mean voltage and current values may be derived that can be used to calculate the same amount of power consumption as for analogous DC values. When converting from AC to DC, the average or mean value is frequently utilized (rectification).
To learn more about Average output voltage refer to:
https://brainly.com/question/15710971
#SPJ4
a tidal power plant has a pool area of 26 km2 . the tide has a range of 8.5 m. how much energy (kwh) is generated in one cycle of filling and emptying the tidal impoundment, if the turbinegenerator efficiency is 75%?
3.676 x [tex]10^{6}[/tex] kWh of energy generated in one cycle of filling and emptying the tidal impoundment.
Energy generated in one filling (or emptying) process is
Energy = [tex]\frac{1}{2}[/tex] ρgA([tex]R^{2}[/tex] – [tex]r^{2}[/tex]), Joules
Where,
ρ = density of sea water = 1025 kg/[tex]m^{3}[/tex]
g = acceleration due to gravity = 9.81 m/[tex]s^{2}[/tex]
A = basin area = 26 km2 = 26 x [tex]10^{6}[/tex] [tex]m^{2}[/tex]
R = minimum head for turbine operation = 3m
E = 1/2 x 1025 x 9.81 x 26 x 106 x 135 J
= 1,76,46,963.75 x [tex]10^{6}[/tex] J
= (1,76,46,963.75 x [tex]10^{6}[/tex]) / (1000 x 3600) kWh
= 4.901 x [tex]10^{6}[/tex] kWh
But the theoretically available tidal energy in one filling process has to be multiplied by 73% or 0.73 to get actual energy generated by the turbine generator.
Therefore, actual energy generated, [tex]E_{actual}[/tex]is given by
[tex]E_{actual}[/tex] = 75% of [tex]E_{theoretical}[/tex]
= 0.75 x 4.901 x [tex]10^{6}[/tex]
= 3.676 x [tex]10^{6}[/tex] kWh
To know more about tidal power plant, visit: https://brainly.com/question/11353919
#SPJ13
discuss why pressure tests of pressurized tanks such as steam boilers, pipes and tanks including gases such as nitrogen, air, oxygen, etc. with high pressure are carried out hydrostatically by using liquids such as water and hydraulic oil.
The reason that pressure tests of pressurized tanks such as steam boilers, pipes and tanks including gases such as nitrogen, air, oxygen, etc. with high pressure are carried out hydrostatically by using liquids such as water and hydraulic oil is because some of them are very volatile such as oxygen and can explode and as such the use of hydrostatic solvent can reduce its temperature.
Why do you use nitrogen for pressure testing?The use of pressure tests is to ensure the integrity of equipment including pressure vessels, pipes, plumbing lines, gas cylinders, boilers, and fuel tanks, pressure tests are a non-destructive option. The piping codes demand that it be verified that a piping system can support its rated pressure and is leak-free.
Nitrogen is free from many of the issues that come with utilizing air or water for pressure testing because it is inert, odorless, and has a low moisture content. Additionally, thanks to portable nitrogen generators, nitrogen is perfect for testing in a range of places.
Tanks and pipes are subjected to hydrostatic pressure testing to check for leaks. A hydrostatic test is carried out by pressurizing the vessel or piping under test, filling it, and then checking for changes in the pressurization level.
Note that there is the district cooling or district heating systems, by performing a pressure test. In addition to ensuring proper operation, this kind of examination will enable us to identify any leaks in a specific pipe so that repairs may be completed.
Learn more about pressure tests from
https://brainly.com/question/10162194
#SPJ1
a steam power plant operating on the simple ideal rankine cycle is considered. the heat input into the cycle is 2728 kj/kg, and the heat output is 2018 kj/kg. determine the thermal efficiency of this cycle.
The average temperature at which heat is fed to the cycle is raised, increasing the Rankine cycle's thermal efficiency. lowering the typical temperature at which the cycle rejects heat.
Power plants that employ coal or nuclear energy frequently use the Rankine cycle, also known as the Rankine Vapor Cycle. A fuel is used in this mechanism to generate heat in a boiler, turning water into steam that expands via a turbine to provide useful work. The Rankine cycle's efficiency is lower than that of a Carnot cycle operating between the same maximum and minimum temperatures because the mean temperature at which heat is provided is lower than the maximum temperature,
Learn more about efficiency here-
https://brainly.com/question/13154811
#SPJ4
which three gauges or indicators are the most important to be aware of? coolant temperature gauge, oil pressure gauge, and high beam indicator fuel gauge, oil pressure gauge, battery voltage gauge coolant temperature gauge, oil pressure gauge, and battery voltage gauge fuel gauge, coolant temperature gauge, and battery voltage gauge
Your three gauges will be: Oil pressure, battery voltage, and a coolant temperature indicator are all included.
What gauges to install in car?Your three gauges will be: Boost Gauge. Oil Pressure Gauge A wideband gauge for the air/fuel ratio.The oil pressure gauge is the most crucial device in the car. A mechanical gauge is the instrument of choice for the majority of racecars. There are many different mechanical gauges available, but one thing to think about is the gauge's overall range.The speedometer and fuel gauge are the two most used gauges. This is because (clearly, we hope) staying aware of your speed is essential to maintaining both your safety and compliance with the law. The speedometer used to be connected to a cable that went into the gearbox box.To Learn more About three gauges Refer To:
https://brainly.com/question/28087119
#SPJ4
How many physically different ways are there to realize V.W.X four 2-input AND gates? Justify your answer.
Answer: 16
Explanation: