Answer:
b. abc
Explanation:
The phase rotation and its sequence is order in which voltage is reached to their respective sources. The wave forms of a polyphase flow through AC source to the panel. The three phase system has two possible sequence which can be a-b-c or c-b-a. The correct answer is therefore b.
Report of invertor to convert 12 volt to 220 volt.
Technician A says that when the malfunction indicator light or service engine light is on you should retrieve the diagnostic trouble code and follow the manufacturers recommended procedure. Technician B says that all obd-ll monitors must have the enabled criteria achieved before a test is performed. Who is correct?
Answer:both
Explanation:
A student lab group is brainstorming the design of an experiment that uses an ammeter (measures current) and different resistors to determine the effect of the resistance of a resistor upon the current in a simple circuit. Which Post-it note describes the most effective design?Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data. Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Move the ammeter to a different location in the circuit. Measure the current at this new location. Continue moving the ammeter to different locations within the circuit but be careful to keep the resistor in a fixed location. Measure and record all current values. Obtain a variety of batteries and build several circuits. Make sure that each circuit has at least one resistor and make sure that the resistance values are different in the different circuits. Place various ammeters in each circuit. Measure the number of batteries and the current for each of the circuits. Record the resistance values used in each of these circuits. Put a 10.0-ohm resistor in a circuit with a single D-cell. Measure the current in the circuit. Add a second D-cell and measure the current with two D-cells. Repeat trials for three, four, and five D-cells, being careful to get accurate current measurements for a fixed amount of resistance in each trial.
Answer:
Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data.
Explanation:
The only design that has resistance varying with everything else remaining the same is the first design. That would be what you'd want to do if you're exploring the effect of resistance on current.
Which of the following sentences is
punctuated incorrectly?
Answer:
Um is there suppose to be a picture with the sentences on
Answer:
It's B I did the test and I was right on B
Explanation:
I don't know I knew it was B
if you are a mechanical engineer answer these questions:
1. Are communication skills (reading, writing, and speaking) necessary in this profession?
2. How are Communicative Competences integrated into this profession?
Answer:
1. Yes, they are all necessary.
2. Both written and verbal communication skills are of the utmost importance in business, especially in engineering. Communication skills boost you or your teams' performance because they provide clear information and expectations to help manage and deliver excellent work.
1. In a mechanical design, it is recommended to use standard size/dimension to overcome uncertainties in stress or material strength.
A. True
B. False
2. Steels' surface fatigue strength can be correlated to their Brinell hardnesses.
A. True
B. False
3. If a material point has three principal stresses 01 = 02 = 03 = 300kpsi, then the maximum shear stress is Tmax = 150kpsi.
A. True
B. False
4. The endurance limit of a material is independent on the size of a part.
A. True
B. False
5. The tensile stress in a bolt is usually calculated through tensile force divided by area of unthreaded rod's cross-section area.
A. True
B. False
6. Edge shear-out or tear-out is one failure mode in bolted or riveted joints.
A. True
B. False
7. Pretension of bolts can be controlled by a torque wrench.
A. True
B. False
8. The material ultimate tensile strength of a spring coil is dependent on its coil diameter.
A. True
B. False
9. Adhesive joints are much stronger in tensile loading than shear loading.
A. True
B. False
10. The dominated loading condition in a helical spring is torsion along coils.
A. True
B. False
11. The principal advantage of conical springs is that the its spring rate is non-linear.
A. True
B. False
12. The dimensions of a bearing is coded by two-digit series numbers according to ABMA, one digit for width and the other one for diameter.
A. True
B. False
13. Three key things to determine selection of bearing are load, life and reliability.
A. True
B. False
14. Straight roller bearings can carry large radial loads and small amount of axial load.
A. True
B. False
15. In the AGMA method of gear analysis, gear strength values are the true material strengths.
A. True
B. False
16. A planetary gear train allows for two degrees of freedom.
A. True
B. False
Answer:
1. A.True
2. B.False
3. B.False
4. A.True
5. A.True
6. A.True
7. A.True
8. B.False
9. B.False
10. A.True
11. B.False
12. A.True
13. A.True
14. B.False
15. B.False
16. A.True
Explanation:
Most steels have endurance and fatigue limit about half the Tensile strength. Tensile strength of material is the limit of stress at which material then breaks. The tensile stress in a bolt is calculated through tensile force.
Suppose we have 999 records of employees Emp1, Emp2, Emp5, Emp6 and so on up to Emp998 and Emp999 stored in a sequence. Hence, records are nothing but a row in the table. In the employee table, we want to insert new records Emp3 and Emp4 in the sequence, and once we have done insertion we need to update and retrieve the record efficiently to optimize the performance of a database by minimizing the access time when query is being executed.
The records in the table represents the employee ID of each employee. Assume the table name is EMPLOYEES and the field name of employee IDs is ID, the following SQL query inserts Emp3 and Emp4 into the employees table.
INSERT INTO EMPLOYEES (ID) values (Emp3), (Emp4)
The complete question requires that we list the pros and cons of solving the problem using Index sequential access method (ISAM).
The advantage of using ISAM is that priorities are given to the indices of the records being inserted. So, Emp3 and Emp4 will be inserted immediately after Emp2.
However, a major disadvantage of using ISAM is that it is very expensive to keep the indices in a sequential order;
See attachment for the illustration of Index sequential access method (ISAM).
Read more about Index sequential access method (ISAM) at:
https://brainly.com/question/4692093
1. Two types of superchargers include
A. turbine and piston.
B. roots-type and centrifugal.
C. double- and single-acting
D. rotary and reciprocating.
A fixed mass of saturated water vapor at 400 kpa is isothermally cooled until it is a saturated liquid. Calculate the amount of heat rejected during this process in kJ/kg.
The amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.
What is heat?
Heat is defined as the process of kinetic energy being transferred from an energy source to a medium or an item. These three mechanisms radiation, conduction, and convection can all transmit energy. These three modes of heat transfer are typically combined, and it often happens on its own. The heat energy can be transformed into other types of energy, such as mechanical and kinetic energy. Thermal (heat) energy is a type of energy that is produced by the movement of particles and is a component of all matter.
The process rejects a certain amount of heat, which is
-q = w + Δu
q = - w - Δu
q = - 185.5 kJ/kg - 1948.9 kJ/kg
q = 2133.4 kJ/kg
Thus, the amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.
To learn more about heat, refer to the link below:
https://brainly.com/question/1429452
#SPJ2
Input resistance of a FET is very high due to A) forward-biased junctions have high impedance B) gate-source junction is reverse-biased C) drain-source junction is reverse-biased D) none of the above
Answer:
B) gate-source junction is reverse-biased
Explanation:
FET is described as an electric field that controls the specific current and is being applied to a "third electrode" which is generally known as "gate". However, only the electric field is responsible for controlling the "current flow" in a specific channel and then the particular device is being "voltage operated" that consists of high "input impedance".
In FET, the different "charge carriers" tend to enter a particular channel via "source" and exits through "drain".
Consider a Diesel cycle that starts (at point a in Fig. 20.7) with air at temperature Ta. The air may be treated as an ideal gas. (a) If the temperature at point c is Tc, derive an expression for the efficiency of the cycle in terms of the compression ratio r. (b) What is the efficiency if Ta
Answer:
b
Explanation:
what is anythin efficiency if ta
There are some sections of the SDS that are not mandatory
True or false
Answer:
True
Explanation:
There are 16 in all and 4 are not mandatory
There are some sections of the SDS that are not mandatory. Thus, option A is correct.
What is SDS?A Safety Data Sheet, previously known as a Material Safety Data Sheet, is a thorough instructional report written by a dangerous product's producer or exporter. It gives a description of something like the product's chemical and physical characteristics.
Sections 1 through 11 and 16 must be used; sections 12 through 15 are optional but could be included. the section which will are not compulsory are:
Section 12: Environmental data
Section 13: Guidelines for Recycling
Section 14: Documentation regarding mobility
Section 15: Relevant data about regulations
In Safety Data Sheet, all the sections are not compulsory or mandatory. this statement is true. Therefore, option A is the correct option.
Learn more about Safety Data Sheet, here:
https://brainly.com/question/1442958
#SPJ2
Question 1 of 8.
What should you do to drive safely in the station?
Turn on your hazard lights
Roll your windows down and turn off the radio
Maintain idle speed (below 5mph)
All of the above
Mark for follow up
Answer: all of the above
Explanation:
To drive safely in the station, the correct option is D. All of the above.
It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.
One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights
Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.
In conclusion, the correct option is D.
Read related link on:
https://brainly.com/question/18889428
In order to enhance net radiation exchange between a high temperature surface and a low temperature surface in an enclosure, one should:________.
(A) polish both surfaces so that they are highly reflective
(B) paint both surfaces so that they are close to a blackbody surface
Answer: Option B
Explanation:
In order to enhance net radiation exchange between a high temperature surface and a low temperature surface in an enclosure, one should: paint both surfaces so that they are close to a blackbody surface but don't polish both surfaces so that they are highly reflective
“Snow Cover Area change Analysis for Kabul Basin”
Summarize how GIS & Remote Sensing is incorporated in this study.
GIS
The full for GIS is : Geographic Information System.
The GIS is a system of mapping that is used to create, analyze, manage and map all the types of data.
It is a method capturing, checking as well as displaying all the data that is related to the position of the surface of earth.
Remote Sensing
Remote sensing is defined as a process where the various physical characteristics of an area are constantly monitored and detected by a process of measuring the reflection of the emitted radiations at ta distance.
The snow covered areas of the Kabul basin can be monitored and analyzed by using the process of GIS and remote sensing.
They provide a continuous source of information and data about snow covered peaks, the amount of snow to the authorities.
Learn More :
https://brainly.in/question/1556256?__cf_chl_captcha_tk__=pmd_2d2d9994422ca43d3cbbcf6322e6c34da175405a-1628654009-0-gqNtZGzNAvijcnBszQ3i
Water discharging into a 10-m-wide rectangular horizontal channel from a sluice gate is observed to have undergone a hydraulic jump. The flow depth and velocity before the jump are 0.8m and 7m/s, respectively. Determine (a) the flow depth and the Froude number after the jump (b) the head loss (c) the dissipation ratio.
Answer:
A) Flow depth = 2.46 m, Froude number after jump = 0.464
B) head loss = 0.572 m
C) dissipation ratio = 0.173
Explanation:
Given data :
Velocity before jump ( v1 ) = 7 m/s
flow depth before jump ( y1 ) = 0.8 m
g = 9.81 m/s
Esi = 3.3 m ( calculated )
attached below is a detailed solution of the problem
Biết op-amp có Vsat = 12V, R1=R2=R3=R4=R, dạng sóng điện áp Vi(t) được cho như
hình 2.16b
a. Tính V0 theo Vi, độ lợi áp AV
b. Vẽ lại dạng sóng điện áp V0(t) khi Vm= 3
8 V
c. Vẽ lại dạng sóng điện áp V0(t) khi Vm = 5V
Answer:
Hello bro
Explanation:
I think i can help you something but can you translate it on english plzz
9. A box contains (4) red balls, and (7) white balls ,we draw( two) balls with return , find 1. Show the sample space & n(s) ..... 2. Probability of all results that appeared in the sample space..
Answer:
The answers to your questions are given below.
Explanation:
The following data were obtained from the question:
Red (R) = 4
White (W) = 7
1. Determination of the sample space, S.
The box contains 4 red balls and 7 white balls. Therefore, the sample space (S) can be written as follow:
S = {R, R, R, R, W, W, W, W, W, W, W}
nS = 11
2. Determination of the probability of all results that appeared in the sample space.
From the question, we were told that the two balls was drawn with return. There, the probability of all results that appeared in the sample space can be given as follow:
i. Probability that the first draw is red and the second is also red.
P(R1) = nR/nS
Red (R) = 4
Space space (S) = 11
P(R1) = nR/nS
P(R1) = 4/11
P(R2) = nR/nS
P(R2) = 4/11
P(R1R2) = P(R1) x P(R2)
P(R1R2) = 4/11 x 4/11
P(R1R2) = 16/121
Therefore, the Probability that the first draw is red and the second is also red is 16/121.
ii. Probability that the first draw is red and the second is white.
Red (R) = 4
White (W) = 7
Space space (S) = 11
P(R) = nR/nS
P(R) = 4/11
P(W) = nW/nS
P(W) = 7/11
P(RW) = P(R) x P(W)
P(RW) = 4/11 x 7/11
P(RW) = 28/121
Therefore, the probability that the first draw is red and the second is white is 28/121.
iii. Probability that the first draw is white and the second is also white.
White (W) = 7
Space space (S) = 11
P(W1) = nW/nS
P(W1) = 7/11
P(W2) = nW/n/S
P(W2) = 7/11
P(W1W2) = P(W1) x P(W2)
P(W1W2) = 7/11 x 7/11
P(W1W2) = 49/121
Therefore, the probability that the first draw is white and the second is also white is 49/121.
iv. Probability that the first draw is white and the second is red.
Red (R) = 4
White (W) = 7
Space space (S) = 11
P(W) = nW/nS
P(W) = 7/11
P(R) = nR/nS
P(R) = 4/11
P(WR) = P(W) x P(R)
P(WR) = 7/11 x 4/11
P(WR) = 28/121
Therefore, the probability that the first draw is white and the second is red is 28/121.
A two-lane, one-way ramp from an urban expressway with a design speed of 30 mi/h connects with a local road at a T-intersection. The turning roadway has a vertical curb on both sides. Determine the width of the turning roadway if the predominant turning vehicles are single unit trucks with some semi-trailers. Use 0.08 for super-elevation if applicable.
Answer:
30 feet
Explanation:
Given data :
design speed = 30 miles/h
super elevation = 0.08
determine the width of the turning roadway
calculate the value of R = V^2 / 15( e + p)
e = 0.08 , p = 0.2 , v = 30
R = (30)^2 / 15 ( 0.08 + 0.2 )
= 900 / 15 ( 0.28 )
≈ 215 ft
pavement width from the calculation above = 28 ft
width of the turning roadway = pavement width + 2 = 30 feet ( because there are two vertical widths joining up the main road at the T junction )
động cơ không đồng bộ 3 pha là gì
Answer:
uhhhhhhh lemme think
Explanation:
A steam turbine generator unit is used to produce electricity, where steam enters the turbine with a velocity of 30 m/s and enthalpy (internal energy) of 3348 kJ/kg. The 1 steam leaves the turbine as a mixture of vapor and liquid having a velocity of 60 m/s and an enthalpy of 2550 kJ/kg. The flow through the turbine is adiabatic, and changes in elevation are negligible. Determine the work output from the turbine, if the mass flow rate is 5kg/s.
Answer:
3.983 MW
Explanation:
Given that:
At the inlet:
Velocity (v₁) = 30 m/s
Enthalpy (h₁) = 3348 kJ/kg
At the outlet:
Velocity (v₂) = 60 m/s
Enthalpy (h₂) = 2550 kJ/kg
Mass flow rate (m) = m₁ = m₂ = 5kg/s
According to the steady flow energy equation:
[tex]Q+ m_1 (h_1 + \dfrac{v_1^2}{2000}+ \dfrac{gz_1}{1000} )= m_2(h_2+\dfrac{v_2^2}{2000}+\dfrac{gz_2}{1000})+W_{shaft}[/tex]
Since the elevation (z) is negligible and flow via the turbine is adiabatic:
Then,
Q = 0 and z₁ = z₂
∴
[tex]W_{shaft} = (mh_1-mh_2) + (\dfrac{mv_1^2-mv_2^2}{2000})[/tex]
[tex]W_{shaft} = ((5*3348) -(5*2550)) + (\dfrac{(5*(30)^2)-(5*(60)^2)}{2000})[/tex]
[tex]W_{shaft} = (16740-12750) + (\dfrac{4500-18000}{2000})[/tex]
[tex]W_{shaft} = (16740-12750) + (-6.75)[/tex]
[tex]W_{shaft} = 3983.25 \ kW[/tex]
[tex]\mathbf{W_{shaft} = 3.983 \ MW}[/tex]
A rate of 0.42 minute per piece is set for a forging operation. The operator works on the job for a full eight-hour day and produces 1,500 pieces. Use a standard hour plan.
Required:
a. How many standard hours does the operator earn?
b. What is the operator's efficiency for the day?
c. If the base rate is 9.80 per hour, compute the earnings for the day.
d. What is the direct labor cost per piece at this efficiency?
e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?
Answer:
b. What is the operator's efficiency for the day?
AND
e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?
Explanation:
The natural variation of a process relative to the variation allowed by the design specifications is known as
Answer:
"Process capability" is the correct answer.
Explanation:
The Process Capability seems to be a method of measuring of how and why the framework performs concerning something like the successful objectives. This same capacity is characterized as that of the client's voice over procedure speech.Through using functionality indicators it analyses the performance with an in-control process with the permissible range.What improves the structured approach in design?
A team is adopting a structured approach in design which helps them to improve the ___ of the design.
Answer:
efficiency
Explanation:
Answer:
The correct answer is Efficiency.
Explanation:
I got it right on the plato test.
What is the following diagram called?
Answer:
business
Explanation:
because shopping has great income
Answer:
is ur question right
Explanation:
is ur question right
is ur question right
An 8-m long, uninsulated square duct of cross section 0.2m x 0.2m and relative roughness 10^-3 passes through the attic space of a house.. Hot air (80°C) enters an 8 m long un-insulated square duct (cross section 0.2 m x 0.2 m) that passes through the attic of a house at a rate of 0.15 m^3 /s. The duct is isothermal at a temperature of 60°C. Determine the rate of heat loss from the duct to the attic space and the pressure difference between the inlet and outlet sections of the duct.
Answer:
the rate of heat loss from the duct to the attic space = 1315.44 W
the pressure difference between the inlet and outlet sections of the duct = 7.0045 N/m²
Explanation:
We know that properties of air 80⁰C and 1atm (from appendix table) are;
density p = 0.9994 kg/m³, Specifice heat Cp = 1008 J/kg.⁰C
Thermal conductivity k = 0.02953 W/m.⁰C, Prandtl number Pr = 0.7154,
Kinematic viscosity v = 2.097 × 10⁻⁵ m²/s
haven gotten that, we calculate the hydraulic diameter of square duct
Dh = 4Ac / P { Ac = is cross sectional area of duct and P = perimeter}
now we substitute a² for Ac and 4a for P ( we know from the question that a = 0.2 m)
Dh = 4a² / 4a
Dh = 4(0.2)² / 4(0.2)
Dh = 0.2 m
Now we calculate the average velocity of air
Vₐ = Vˣ / Ac { vˣ = volume flow rate of air}
Vₐ = Vˣ / a² { Ac = a² }, we know that a = 0.2m₂, Vˣ = 0.15 m³
Vₐ = 0.15 / (0.2)²
Vₐ = 3.75 m/s
Next we calculate the Reynolds number
Re = Vₐ Dh / V
Re = (3.75 × 0.2) / 2.097× 10⁻⁵
Re = 35765.379
The Reynolds number IS GREATER than 10,000
so the flow is turbulent and entry length in this case is nearly 10 times the hydraulic diameter
Lh ≈ Lt ≈ 10D
= 10 × 0.2
= 2m
As this length is quite small when compared to the total of tube, we assume fully developed flow for the entire tube length.
Now we calculate the Nusselt number from this relation;
Nu = 0.023 Re⁰'⁸ Pr⁰'³
so we substitute for Re and Pr
Nu = 0.023(35765.379)⁰'⁸ (0.7154)⁰'³
Nu = 91.4
Now calculate the convective heat transfer coefficient
h = Nu × K/ Dh
we substitute
h = 91.4 × 0.02953 W/m.°C / 0.2 m
h = 13.5 W/m².°C
We calculate the surface area of the square duct
Aₓ = 4aL { L= length of duct}
we substitute
Aₓ = 4 × 0.2 × 8
Aₓ = 6.4 m²
Mass flow rate of air
m = pVˣ
we substitute again ( from our initials)
m = 0.9994 kg/m₃ × 0.15 m³/s
m= 0.150 kg/s
We calculate the exit temperature of the air from the duct
Te = Ts - (Ts -Ti) exp ( - hAₓ / mCp)
we know that
Ts = 60°C , Ti = 80°C, h = 13.5 W/m².°C , Aₓ = 6.4m², m = 0.150 kg/s , Cp = 1008 J/kg.°C
we substitute
Te = 60 - (60-80) exp(- ((13.5 × 6.4)/(0.15 × 1008))
Te = 71.3°
Now we calculate the rate of heat loss from the duct.
Q = mCp ( Ti -Te )
we substitute again
Q = 0.150 × 1008 × ( 80 - 71.3 )
Q = 1315.44 W
Next we calculate the estimated friction factors by using Haaland equation
1/√f = - 1.8log₁₀ [ 6.9/Re + (E/D)/3.7)¹'¹¹]
we know that E/D = relative roughness = 10⁻³
we substitute
so
1/√f = - 1.8log₁₀ [ (6.9/35765.379) + ( 10⁻³/3.7)¹'¹¹]
1/√f = - 1.8log₁₀ { 0.000192924 + 0.00010947}
1/√f = - 1.8log₁₀ 0.000302324
√f = 1/6.334
f = (1/6.334)²
f = 0.02492
We calculate the pressure difference between inlet and outlet sections of the duct
ΔPl = fLPVa² / Dh × 2
ΔPl = {0.02492 × 8 × 0.9994 × (3.75)²} / 0.2 × 2
ΔPl = 2.8018 / 0.4
ΔPl = 7.0045 N/m²
Therefore pressure deference is 7.0045 N/m²
An AC generator supplies an rms voltage of 120 V at 50.0 Hz. It is connected in series with a 0.650 H inductor, a 4.80 μF capacitor and a 301 Ω resistor.
(a) What is the impedance of the circuit?
(b) What is the rms current through the resistor?
(c) What is the average power dissipated in the circuit?
(d) What is the peak current through the resistor?
(e) What is the peak voltage across the inductor?
(f) What is the peak voltage across the capacitor?
The generator frequency is now changed so that the circuit is in resonance. What is that new (resonance) frequency?
Answer:
Explanation:
f = 50.0 Hz, L = 0.650 H, π = 3.14
C = 4.80 μF, R = 301 Ω resistor. V = 120volts
XL = wL = 2πfL
= 2×3.14×50* 0.650
= 204.1 Ohm
Xc= 1/wC
Xc = 1/2πfC
Xc = 1/2×3.14×50×4.80μF
= 1/0.0015072
= 663.48Ohms
1. Total impedance, Z = sqrt (R^2 + (Xc-XL)^2)= √ 301^2+ (663.48Ohms - 204.1 Ohm)^2
√ 90601 + (459.38)^2
√ 90601+211029.98
√ 301630.9844
= 549.209
Z = 549.21Ohms
2. I=V/Z = 120/ 549.21Ohms =0.218Ampere
3. P=V×I = 120* 0.218 = 26.16Watt
Note that
I rms = Vrms/Xc
= 120/663.48Ohms
= 0.18086A
4. I(max) = I(rms) × √2
= 0.18086A × 1.4142
= 0.2557
= 0.256A
5. V=I(max) * XL
= 0.256A ×204.1
=52.2496
= 52.250volts
6. V=I(max) × Xc
= 0.256A × 663.48Ohms
= 169.85volts
7. Xc=XL
1/2πfC = 2πfL
1/2πfC = 2πf× 0.650
1/2×3.14×f×4.80μF = 2×3.14×f×0.650
1/6.28×f×4.8×10^-6 = 4.082f
1/0.000030144× f = 4.082×f
1 = 0.000030144×f×4.082×f
1 = 0.000123f^2
f^2 = 1/0.000123048
f^2 = 8126.922
f =√8126.922
f = 90.14 Hz
Punctuate or edit the following sentences. Your punctuation and/or revisions should reflect best TW style and grammar writing practices.
1. The author an expert in cybersecurity will speak via Zoom this Wednesday.
2. Williams' book contains many illustrations, this makes it quick reading.
3. Based on the available evidence the university administrators have opted for a hybrid format for the fall quarter which begins September 20.
4. (Thesis statement) Free laptops should be offered to all students who need them.
I inferred you want literal editing of the text above.
Explanation:
Here's a correction of the sentences:
1. The author, an expert in cybersecurity will speak via Zoom on Wednesday.
In this sentence, punctuation mark ( , ) was added and the word 'this' was replaced with 'on'.
2. Williams' book contains many illustrations, which makes it easy to read.
Added punctuation and made a revision of the sentence.
3. Based on the available evidence, the university administrators have opted for a hybrid format for the fall, which begins September 20.
Mainly added punctuations to make the senstence clarer.
4. (Thesis statement) I believe Free laptops should be offered to all students who need them.
Made a few additions.
If the tank is designed to withstand a pressure of 5 MPaMPa, determine the required minimum wall thickness to the nearest millimeter using the maximum-shear-stress theory. Apply a factor of safety of 1.5 against yielding.
Answer: hello some aspects of your question is missing below is the missing information
The gas tank is made from A-36 steel and has an inner diameter of 1.50 m.
answer:
≈ 22.5 mm
Explanation:
Given data:
Inner diameter = 1.5 m
pressure = 5 MPa
factor of safety = 1.5
Calculate the required minimum wall thickness
maximum-shear-stress theory ( σ allow ) = σγ / FS
= 250(10)^6 / 1.5 = 166.67 (10^6) Pa
given that |σ| = σ allow
3.75 (10^6) / t = 166.67 (10^6)
∴ t ( wall thickness ) = 0.0225 m ≈ 22.5 mm
"The transistor base-emitter voltage (VBE) a. increases with an increase in temperature. b. is not affected by temperature change. c. decreases with an increase in temperature. d. has no effect on collector current."
Answer:
C) Decreases with an increase in temperature
Explanation:
As the temperature of a transistor increases, the thermal runaway property of the transistor becomes more significant and the transistors, conducting more freely as a result of the rise in temperature, causes an increase in the collector current or leakage current. The transistor base-emitter voltage decreases as a result.
With increased heating due to heavy current flow, the transistor is damaged.