Answer: Designs need to be feasible.
Explanation: don’t know, guessed got it right
Which of the following has led to a safer and more prosperous global community within the last century? the Bronze Age composite materials new materials ceramics
Answer:
The bronze age
Answer: New materials
Explanation: I read it in the article.
A data bus can be visualized as a multilane highway
A. and each component is located at an intersection where it will turn or go straight
B. with each component having an individual address
C. and each component located in a curve where the data will slow down
D. with each component acting as a traffic light, stop-go
Answer:
B. with each component having an individual address
Explanation:
A data bus is a system within a computing system, that consists of a set of wires or connectors, that provides transportation for data. A data bus can transfer data and information through a computing system, or between two or more computing systems. Each component in the computer has its own unique address by which data or information is sent to it, to or fro the central processing unit, and the data or information travelling through the data bus, which serves as the highway, reaches each component using this address. This is analogous to the postal service system of moving letters and packages, through a series of networks that locates the address of the receiver.
Below are listed the atomic weight, density and atomic radius for three hypothetical metal alloys. For each determine whether its crystal structure is FCC, BCC, or simple cubic and then justify your determination.
Alloy
A
B
C
Atomic
Weight
(g/mol)
43.1
184.4
91.6
Density
(g/cm
3)
6.40
12.30
9.60
Atomic
Radius
(nm)
0.122
0.146
0.137
The names of each of the crystal structures for each of the given metal alloys are; Alloy A is BCC structure; Alloy B is SC structure; Alloy C is BCC structure
What is a Crystal Structure?To solve for each of the three given alloys, we will need to do so by trial and error method to calculate the density and compare it to the value given in the problem.
The density formula is;
ρ = nA/(V_c × N).
Where;
n is 1, 2 and 4 for SC, BCC & FCC crystal structures respectively.
A is atomic weight
V_c is volume expressed as a³.
a is given by 2R,4R/√3, 2R√2 for SC, BCC & FCC crystal structures respectively with R being the atomic radius.
N is avogadros number of atoms and has a constant value of 6.022 × 10^(23) atoms/mol
A) For metal alloy A, we are given;A = 43.1 g/mol
If we assume it's a BCC structure, then;
n = 2
V_c = a³ = (4R/√3)³ = (4 × 1.22 × 10^(-8) × 1/√3)³ = 22.4756 × 10^(-24) cm³
N = 6.022 × 10^(23) atoms/mol
Plugging in the relevant values into the density formula, we have;
ρ = (2 × 43.1)/(22.4756 × 10^(-24) × 6.022 × 10^(23)) ≈ 6.4 g/cm³
This value is same as the one in the question, thus metal alloy A is a BCC crystal structure
B) For metal alloy B, we are given;A = 184.4 g/mol
If we assume it's a SC structure, then;
n = 1
Thus;
V_c = a³ = (2 × 1.46 × 10^(-8))³ = 24.897 × 10^(-24) cm³
Plugging in the relevant values into the density formula, we have;
ρ = (1 × 184.4)/(24.897 × 10^(-24) × 6.022 × 10^(23)) ≈ 12.3 g/cm³
This value is same as the one in the question, thus metal alloy B is an SC crystal structure
C) For metal alloy C, we are given;A = 91.6 g/mol
If we assume it's a BCC structure, then;
n = 2
V_c = a³ = (4R/√3)³ = (4 × 1.37 × 10^(-8) × 1/√3)³ = 31.67 × 10^(-24) cm³
Plugging in the relevant values into the density formula, we have;
ρ = (2 × 91.6)/(31.67 × 10^(-24) × 6.022 × 10^(23)) ≈ 9.6 g/cm³
This value is same as the one in the question, thus metal alloy C is an SC crystal structure.
Read more about crystal structures at;https://brainly.com/question/14831455
Copper (Cu) has FCC crystal structure. Atomic mass of Cu is 63.55 gmol-1 and radius of a copper atom is 0.128 nm, mean speed of conduction electrons in Cu is 1.5 × 10^6 m/s and frequency of vibration of the Cu atoms at 27 ° is 4 × 10^12 s-1. Nordheim’s Coefficient of Au in Cu is 5500 nΩ −m. a) Calculate the atomic density of copper b) Estimate the drift mobility of electrons in Cu c) Find the resistivity of pure Cu d) Find the resistivity of Cu if 1 at.% of Au is mixed in Cu. pls solve it
Answer:
First, there are 4 atoms in the FCC unit cell.
The unit volume of the unit can be calculated based on the atomic radii, in which case the hypotenuse of the cube of the unit cell would be 4 X 0.1278
Next, find the weight of one atom by taking (63.55g / mol) X (mols / 6.0221415 x 10 ^ 23 atoms)
So now you have all the numbers you need. Take the weight of the atom X 4 divided by the cube volume taken from the hypotenuse.
Explanation:
Which of the following statement(s) are true?
A. NAND gates output a 1 when each of its inputs is a 1.
B. All circuits can be created using only NOR gates.
C. A circuit with 4 inputs has 16 possible combinations (truth table lines).
D. You should never tie 2 outputs of two distinct circuits together.
In a voltage-divider biased npn transistor, if the upper voltage-divider resistor (the one connected to VCC) opens:______.
a) the transistor goes into cutoff.
b) the transistor goes into saturation.
c) the transistor burns out.
d) the supply voltage is too high.
Answer:
The transistor goes into cutoff ( A )
Explanation:
In a voltage-divider biased npn transistor, if the upper voltage-divider resistor (the one connected to VCC) opens the transistor goes into cutoff
Voltage-divider biased npn transistor is a transistor that consists of some resistors and this resistors help to divide and distribute the voltage entering the transistor into its correct levels ( this is the most popular means of biasing a BJT transistor )
Which of the following answer options can damage flexible and extension cords?
Staples
Door or window
Fastenings
Aging
Abrasion from adjacent
(Select all that apply)
Answer:
staples
Door or window
Explanation:
staples.- can hit the internal core and risk of electrocution.
Door or window - can damage the outer core
staples.- can hit the internal core and risk of electrocution or Door or window - can damage the outer core.
What is Extension cords?A length of flexible electrical power cable (flex) with a plug on one end and one or more sockets on the other end (often of the same kind as the plug) is known as an extension cord (US), power extender, drop cord, or extension lead (UK).
The phrase is also used to describe extensions for various types of cabling, but it mainly refers to mains (home AC) extensions.
The phrase "adapter cord" may be used if the plug and power outlet are of different types. Although they can be produced up to 300 feet long, most extension cords are between two and thirty feet long.
Therefore, staples.- can hit the internal core and risk of electrocution or Door or window - can damage the outer core.
To learn more about Extension cords, refer to the link:
https://brainly.com/question/14925233
#SPJ2
The magnitude of the line voltage at the terminals of a balanced Y-connected load is 660 V. The load impedance is 240-j70 Ω/Φ. The load is fed from a line that has an impedance of 0.5 + j4 Ω/Φ.
A) What is the magnitude of the line current?
B) What is the magnitude of the line voltage at the source?
Answer:
A) magnitude of the line current = 15.24 A
B) 6583.94 v
Explanation:
Given data :
magnitude of line voltage at terminal = 6600 v
load impedance = 240 - j70 Ω/∅
impedance of load fed from a line = 0.5 + j4 Ω/∅
attached below is the detailed solution
Trevor typically works on the highways doing maintenance. Who is most likely his employer? a large private company himself the government a small private company
Answer: The Government.
Explanation: Highways are usually a roads where people travel on. They are usually owned mainly by the government some are owned by private entities. Of the above options the most possible employer of Trevor is the government as majority of the highways are usually owned by the government.
The government provide several services on the highways such as roads maintenance, security, accidents and emergency cares etc
Answer: I think it's C, I hope this helps ;)
10. The repair order is a legal document because
A. the shop owner signs it
B. it's signed by the customer.
C. the manufacturer authorizes it
D. it's paid for by the customer
A rectangular channel 3 m wide carries 4 m3/s of water at a depth of 1.5 m. If an obstruction 15 cm high is placed across the channel, calculate the elevation of the water surface over the obstruction. What is the maximum height of the obstruction that will not cause a rise in the water surface upstream
Answer:
the elevation of the water surface over the obstruction is highest at 1.341 m
the maximum height of the obstruction h = 0.159 m
Explanation:
From the given information:
The diagrammatic expression for the water profile showing a rectangular channel with 3 cm width carrying a 4 m3/s of water at a depth of 1.5 m with an obstruction 15 cm high is placed across the channel can be seen in the diagram attached below.
To calculate the elevation of the water surface over the obstruction, we need to determine the following:
a. the velocity of the channel
b. the froude number at the upstream of the obstruction
c. the specific energy level
To start with the velocity V of the channel.
[tex]V_1 = \dfrac{Q}{A} \\ \\ V_1 = \dfrac{4 \ m^3/s}{(3 \times 1.5 ) m^2 } \\ \\ V_1 = \dfrac{4 \ m^3/s}{4.5 \ m^2}[/tex]
[tex]V_1 = 0.88 \ m/sec[/tex]
The froude number at the upstream of the obstruction
[tex]F _{\zeta} = \dfrac{V_1}{\sqrt{gy__1}}[/tex]
[tex]F _{\zeta} = \dfrac{0.88}{\sqrt{9.81 \times 1.5}}[/tex]
[tex]F _{\zeta} = \dfrac{0.88}{\sqrt{14.715}}[/tex]
[tex]F _{\zeta} = \dfrac{0.88}{3.836}[/tex]
[tex]F _{\zeta} =0.229[/tex]
[tex]F _{\zeta} \simeq0.3[/tex] which is less than the subcritical flow.
Similarly, the specific energy level for this process can be expressed as:
[tex]E_1 = \dfrac{V_1^2}{2g}+y_1[/tex]
[tex]E_1 = \dfrac{0.88^2}{2 \times 9.81 }+1.5[/tex]
[tex]E_1 = \dfrac{0.7744}{19.62 }+1.5[/tex]
[tex]E_1 =0.039469+1.5[/tex]
[tex]E_1 =1.539469[/tex]
[tex]E_1 \simeq1.54 \ m[/tex]
[tex]E_2 + \Delta z = E_1[/tex]
[tex]E_2= E_1 - \Delta z[/tex]
[tex]E_2= (1.54 - 0.15) \ m[/tex]
[tex]E_2=1.39 \ m[/tex]
Suppose ;
[tex]V_1 y_1 = V_2y_2\\ \\ Then; \ making \ V_2 \ the \ subject \ of \ the \formula\ we \ have: \\ \\ \\V_2 = \dfrac{V_1 y_1}{y_2} ---- (1)[/tex]
From the energy equation:
[tex]E_2 + \Delta z = E_1[/tex]
we can now substitute the above derived parameter and have :
[tex]E_2 + \Delta z=y_1 + \dfrac{V_1^2}{2g}[/tex]
[tex]E_2 =y_1 + \dfrac{V_1^2}{2g} - \Delta z[/tex]
[tex]E_2 =y_2 + \dfrac{V_2^2}{2g}[/tex]
replace the value of [tex]V_2[/tex] =[tex]\dfrac{V_1 y_1}{y_2}[/tex] in equation (1), we have:
[tex]E_2 =y_2 + \dfrac{( \dfrac{V_1y_1}{y_2})^2}{2g}[/tex]
[tex]E_2 =y_2 + \dfrac{ {V_1^2y_1^2}}{2gy_2^2}[/tex]
[tex]E_2 \times y_2^2 =y^3_2 + \dfrac{ {V_1^2y_1^2}}{2g}[/tex]
[tex]y^3_2 - E_2y^2_2 + \dfrac{V_1^2y_1^2}{2g}=0[/tex]
Replacing our values now; we have:
[tex]y^3_2 - 1.39 \times y^2_2 + \dfrac{0.88^2 \times 1.5^2}{2 \times 9.81}=0[/tex]
[tex]y^3_2 - 1.39 \times y^2_2 + \dfrac{1.7424}{19.62}=0[/tex]
[tex]y^3_2 - 1.39 \times y^2_2 + 0.0888=0[/tex]
[tex]y^3_2 - 1.39 y^2_2 + 0.0888=0[/tex]
[tex]y_2 = 1.341 \ m \\ \\ y_2 = - 0.232 \ m \\ \\ y_2 = 0.281 \ m[/tex]
Therefore,the elevation of the water surface over the obstruction is highest at 1.341 m
What is the maximum height of the obstruction that will not cause a rise in the water surface upstream
In order to determine the maximum height , we need to first estimate the rise in water level surface of [tex]\Delta z[/tex]
[tex]\Delta z[/tex] = 1.5 - (1.341+ 0.15) m
[tex]\Delta z[/tex] = (1.5 - 1.491) m
[tex]\Delta z[/tex] = 0.009 m
Finally, the maximum height of the obstruction h = (0.009 + 0.15 )m
the maximum height of the obstruction h = 0.159 m
A helical compression spring is to be made with oil-tempered wire ol 4 mm diameter with a spring index of C = 10 The spring is to operate inside a hole, so buckling is not o problem and the ends can be left plan The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm (a) Determine the spring rate (b) Determine the minimum hole diameter tot the spring to operate in (c) Determine the total number of coils needed (d) Determine the solid length.
Answer:
a) the spring rate is 3.333 N/mm
b) the minimum hole diameter for the compression spring is 44 mm
c) the total number of coils needed is 11.6
d) the solid length is 50.4 mm
Explanation:
a)
to calculate the mean spring coil diameter, we take a look at the expression from the relation;
D = Cd
where C is the spring index ( 10 ) and d is the diameter of helical compression spring (4 mm)
so we substitute
D = 10 × 4 = 40 mm
Torsional stiffness G for the tempered wire with diameter 4 mm is 77.2 Gpa ( 77.2 × 10³ Mpa) ( obtained from Table: Mechanical properties of spring wires).
so when the spring is compressed, the spring force is given by the following expression(realtion)
Fs = k × ys
where ys is the deflection of the spring (15 mm) and k is the spring rate, Fs is the force (50N)
so we substitute
50N = k × 15mm
k = 50N / 15mm
k = 3.333 N/mm
∴ the spring rate is 3.333 N/mm
b)
to calculate the minimum hole diameter for the compression spring
Now the entire spring is within a hole in the ground, therefore the hole should have a diameter equal to the outer diameter of the spring.
so D₀ = D + d
and from our initial equations, the mean spring coil diameter D = 40mm and the diameter of the helical compression spring d = 4mm
we substitute
D₀ = 40 + 4
D₀ = 44 mm
the minimum hole diameter for the compression spring is 44 mm
c)
Consider the following relation to calculate the total number of coils needed
Na coils are actually working to support the springs structure and its all dependent on the cut at the edge (end). ( from the table, Nt elates to Na)
Na = (d⁴G) / 8D³k
where the mean spring coil diameter D = 40mm and the diameter of the helical compression spring d = 4mm, G is the torsional stiffness (77.2 × 10³ Mpa), the the spring rate k is 3.333 N/mm
so we substitute
Na = (4⁴(77.2 × 10³)) / ( 8(40³)(3.333))
Na = 19,763,200 / 1,706,496
Na = 11.6
the total number of coils needed is 11.6
d)
As the number of active coils and total number of coils are the same, we get the following relation;
Na = Nt
Nt which is also total number of coils
Now to calculate the solid length
Ls = d ( Nt + 1 )
so we substitute
Ls = 4 ( 11.6 + 1 )
Ls = 50.4 mm
the solid length is 50.4 mm
The spring rate is of the spring is 3.33N/mm, the minimum hole diameter required for the spring to operate in is 44mm while the number of coil needed is 11.6 or approximately 12 and the solid length of the spring is 50.4mm
Given data:
d=4mmC=10mm; D/d = mean coil diameter / wire diameter = 10; D = 10 * 4 = 40mm.Free length of the spring = 80mmForce (f)= 50Nδ=15mma) Spring rate:
[tex]k = f/[/tex]δ = [tex]50/15=3.33N/mm[/tex]
b) Minimum hole diameter;
The minimum hole diameter(D[tex]_i[/tex]) is the sum of diameter of the wire + D
[tex]D_i=40+4=44mm[/tex]
c) Total number of coils needed:
To solve this, we need to use a constant known as the modulus of rigidity and it's given as G = [tex]77.2*10^3N/mm[/tex]
From δ=[tex]\frac{8fD^3N}{Gd^4}[/tex]
Making N the subject, we would have
[tex]N=\frac{15*77.2*10^3*4^4}{8*50*40^3}=11.58[/tex]≈11.6 coils
The number of coils needed is 11.6 coils or approximately 12 coils.
d) The solid length;
The solid length formula is given as
[tex]L_s=(N+1)d=(11.6+1)*4=50.4mm[/tex]
Learn more on elasticity here:
https://brainly.com/question/9821607
https://brainly.com/question/2901244
https://brainly.com/question/14468674
What would happen if an exposed film was accidentally placed in the fixer before being placed in the developer
the amount of phase shift between input and output signal is important when measuring ____ circuit
Answer:
The amount of phase shift between input and output signal is important when measuring a common emitter amplifier circuit.
Explanation:
the amount of phase shift between input and output signal is important when measuring a common emitter amplifier circuit
In signal processing, phase distortion is change in the shape of the waveform, that occurs when the phase shift introduced by a circuit is not directly proportional to frequency.
In a common emitter amplifier circuit there is an 180-degree phase shift between the input and output waveforms.
Drag each tile to the correct box.
Arrange the types of movie discs in terms of the amount of content they can hold.
DVD
Blu-ray
CD
->
Answer:
Bluray
DVD
CD
Explanation:
Blu ray can hold 25gb per layer
Dvd can hold 4.7GB on a single layer
Cd can hold around 737 mb
Also, dvds can go up to 2 layers
Blu ray can go up to 4
Answer:
CD
↓
DVD
↓
Blu-ray
Explanation:
Sam constructs a circuit, connects a lead acid battery of 2 V to a lamp of resistance 3 Ω and places an ammeter across it. What must be the reading of the ammeter?
A.
0.66 A
B.
0.5 A
C.
0.54 A
D.
0.61 A
Answer:
A. 0.66 Amps
Explanation:
Using ohms law, we can say that Voltage is equivalent to Current times Resistance. We are given the voltage and the resistance of the circuit, so we simply need to find the current.
V = IR
Solve for I, where V = 2volts and R = 3ohms.
V = IR
V * 1/R = I * R * 1/R
I = V/R
I = 2/3 Amps
Hence, we should choose option A, 0.66 Amps for the current in this simple circuit.
Cheers.
5) Calculate the LMC wal thickness of a pipe and tubing with OD as 35 + .05 and ID as 25 + .05 A) 4.95 B) 5.05 C) 10 D) 15.025
Answer:
B) 5.05
Explanation:
The wall thickness of a pipe is the difference between the diameter of outer wall and the diameter of inner wall divided by 2. It is given by:
Thickness of pipe = (Outer wall diameter - Inner wall diameter) / 2
Given that:
Inner diameter = ID = 25 ± 0.05, Outer diameter = OD = 35 ± 0.05
Maximum outer diameter = 35 + 0.05 = 35.05
Minimum inner diameter = 25 - 0.05 = 24.95
Thickness of pipe = (maximum outer wall diameter - minimum inner wall diameter) / 2 = (35.05 - 24.95) / 2 = 5.05
or
Thickness = (35 - 25) / 2 + 0.05 = 10/2 + 0.05 = 5 + 0.05 = 5.05
Therefore the LMC wall thickness is 5.05
Ten dollars per hour is about how much income per year
Answer:
see below
Explanation:
10 per hour
example: 37.5 hours in a week
10 x 37.5 hours per week x 52 weeks in a year
19,500 per year.
you can use the above calculation depending on how much you want to work per week.
For the reactions of ketone body metabolism, _______.
A. NADH is produced by catabolism of D‑β‑hydroxybutyrate.
B. Liver lacks thiolase and therefore cannot use ketone bodies as a fuel.
C. Conversion of 2 acetyl-CoA to acetoacetyl-CoA is accompanied by hydrolysis of ATP to AMP and PPi.
D. The enzymes that catalyze biosynthesis of ketone bodies are found in the cytosol of hepatocytes.
Answer:
Is
Explanation:
Who is father of Engineer?
John Smeatom, U.K. 18th century, was the first self-proclaimed, civil engineer in the 18th century and IS considered “the father of modern, civil engineering”.
hoped this helped! :)
Answer:
Sir Mokshagundam Visvesvaraya
A concrete column has a diameter of 390 mm and a length of 2.8 m . If the density (mass/volume) of concrete is 2.45 Mg/m3, determine the weight of the column in pounds.
Answer: 1804.61 lbs
Explanation:
Given, diameter of concrete column = 390 mm
= 0.390 m [ 1 mm =0.001 m]
⇒ Radius = [tex]\dfrac{0.390}{2}=0.195\ m[/tex]
also, Length = 2.8 m
Volume of column (cylindrical)= [tex]\pi r^2l[/tex]
[tex]=(3.14)(0.195)^2(2.8)[/tex]
[tex]=0.3343158\ m^3[/tex]
Density [tex]=\dfrac{Mass }{Volume}=2.45\ Mg/m^3[/tex]
⇒ Mass = 2.45 x (Volume)
= 2.45 (0.3343158) Mg
= 0.81907371 Mg
⇒ Mass = 819.07271 kg [1 Mg =1000 kg]
Weight = [tex]{mass}\times{gravity}={819.07271}\times{9.8}=8026.91\ N[/tex]
1 N= 0.22482 lb
Then, Weight = [tex]0.22482\times 8026.91=1804.61\ lb[/tex]
Weight of the column in pounds.= 1804.61 lbs (approx)
Weight of the column is 1804.61 lbs.
Given that,
Diameter of column is 390mm or 0.39m.Length (l) of column is 2.8m.Density of column is 2.45 Mg/m3According to the given data, calculation are as follows,
Diameter = 0.39m
So, radius (r) = 0.39 [tex]\div[/tex] 2 = 0.195m
Volume of column = [tex]\pi r^{2}l [/tex]
By putting the value, we get
Volume = [ (3.14)[tex]\times[/tex] [tex](0.195)^{2} [/tex] [tex]\times[/tex] 2.8m ]
= [tex]0.3343158m^{3} [/tex]
Now, as we know that,
Density = Mass [tex]\div[/tex] Volume
Or, Mass (M) = Density [tex]\times[/tex] Volume
= 2.45 [tex]\times[/tex] 0.3343158
= 819.07271 kg
Now Weight = (M [tex]\times[/tex] Gravity ) Value of gravity is 9.8.
Weight = 819.07271 kg [tex]\times[/tex] 9.8
= 8026.91N
Where, 1N = 0.22482 lbs
So, Weight of the column = 1804.61 lbs
Learn more : https://brainly.com/question/21667661
The Ksp for Ag2CrO4 is 9.0 x 10-12. If 200 mL of 0.0050 M AgNO3 is combined with 300 mL of 0.0020 M K2CrO4, will a precipitate form?
Answer:
Qsp > ksp
Explanation:
given data
Ag2CrO4 = 9.0 × [tex]10^{-12}[/tex]
solution
new [[tex]Ag^+[/tex]] = [tex]\frac{0.005 \times 200}{200+300}[/tex] = 0.002 M .................1
and
new [[tex]CrO^{2-}_4[/tex]] = [tex]\frac{0.002 \times 300}{200+300}[/tex] = 0.0012M ..............2
so here solubility equation will be as
[tex]Ag_2CrO_4(s)[/tex] ⇄ 2[tex]Ag^+[/tex] (aq) + [tex]CrO^{2-}_4[/tex] (aq) ......................3
so
Qsp = [tex][Ag^+]^2[/tex] [ [tex]CrO^{2-}_4[/tex]]
put here value
Qsp = (0.002)² × (0.0012)
Qsp = 4.80 × [tex]10^{-9}[/tex]
so that we can say that Qsp > ksp
Represent each of the following combinations ~f units in the correct SI form using an appropriate prefix:______
(a) m/ ms,
(b) µkm,
(c) ks/ mg,
(d) km· µN.
Answer:
(a) km/s
(b) mm
(c) Gs/kg
(d) mmN
Explanation:
(a) Given:
m / ms => the proper SI unit should be m/s
So let's convert to m/s
m / ms = [tex]\frac{m}{ms}[/tex]
The denominator is ms which means milliseconds.
But milli = 10⁻³
∴ [tex]\frac{m}{ms}[/tex] = [tex]\frac{m}{10^{-3}s}[/tex] = [tex]\frac{10^3m}{s}[/tex]
Also 10³ = kilo (k)
[tex]\frac{10^3m}{s}[/tex] = [tex]\frac{km}{s}[/tex]
∴ m / ms = [tex]\frac{km}{s}[/tex] = km/s
(b) Given:
μkm => the proper SI unit should be m
So let's convert to m
μkm = 10⁻⁶ km [since μ = 10⁻⁶]
=> μkm = 10⁻⁶ x 10³ m [since k = 10³]
=> μkm = 10⁻³ m
But 10⁻³ = milli (m)
=> μkm = 10⁻³ m = mm
∴ μkm = mm
(c) Given:
ks/mg => the proper SI unit should be s/kg
So let's convert to s/kg
ks/mg = 10³s / mg [since k = 10³]
=> ks/mg = 10³s / 10⁻³g [since m = 10⁻³]
=> ks/mg = 10³ x 10³ s / g
=> ks/mg = 10⁶ s / g
=> ks/mg = [tex]\frac{10^6 s}{g}[/tex]
Multiply the numerator and denominator by 10³
=> ks/mg = [tex]\frac{10^6 X 10^3s}{10^3 X g}[/tex]
=> ks/mg = [tex]\frac{10^9s}{10^3 X g}[/tex]
=> ks/mg = [tex]\frac{Gs}{10^3 X g}[/tex] [since 10⁹ = Giga (G) ]
=> ks/mg = [tex]\frac{Gs}{kg}[/tex] [since 10³ = Kilo (k) ]
∴ ks/mg = [tex]\frac{Gs}{kg}[/tex] = Gs/kg
(d) Given:
km.μN => the proper SI unit should be mN or Nm
So let's convert to km.μN
km.μN = 10³m.μN [since k = 10³]
=> km.μN = 10³m.10⁻⁶N [since μ = 10⁻⁶]
=> km.μN = 10⁻³ mN
=> km.μN = mmN [since m = milli = 10⁻³]
∴ km.μN = mmN
Pick up the correct statement from the following:
A. The theory of formation of concrete is based on the phenomena of formation of voids
B. The bulking of sand is taken into account while volumetric proportioning of the aggregates
C. The dry sand and the sand completely flooded with water, have practically the same volume
D. All the above
Answer:
D. All the above
Explanation:
A is correct. The theory of formation of concrete is based on this phenomenon of formation of voids because, a coarse aggregate aggregate on its own, contain voids. When a fine aggregate like sand is added, it occupies these voids. Further, when finely powdered cement is added to the mixture, it further occupies the voids between the sand particles.
B is correct. The bulking of sand should be taken into account when volumetric proportioning of the aggregates is adopted. Otherwise, less quantity of concrete per bag of cement will be produced, which naturally will increase the cost of concrete. This is because sand particles when left on their own, do not pack properly near each other due to sand buckling, leaving too many void spaces between the sand particles.
C is correct . The dry sand and the sand completely flooded with water have practically the same volume. This is due to the bulking of sand. When water is added to the sand, up to complete flooding, the sand particles pack near each other and the amount of bulking of sand is decreased. The addition of the volume of water, leads to a decrease in the volume of the sand due to the extra voids. These cancels out to practically leave the dry sand and the flooded sand with the same volume.
How is the caliber of a rifle or handgun determined
How can visual communication enhance the message conveyed with the speaker? Cite with a particular situation where in it is best to use visual communication
Answer:
1) Visual Communication involves the use of images ans symbolism for the exchange of ideas from a source to the intended audience.
Visual Communication can help enhance the message conveyed by the speaker when the message being conveyed is new to the audience, such as instructional or educational presentation by enable the audience to more quickly understand the the point of view of the speaker
2) A particular situation where it is best to use visual communication is in a communication that involves giving of traffic and way finding details to a tourist
Explanation:
Visual communication can improve the message that is transmitted with the speaker through the transmission of additional concepts to the message, such as gestures, body expressions or communicative looks, which add meanings to the words emitted.
Today, visual communication is extremely developed and is designed to perform several tasks at once. Communication through visual images is progressing thanks to the development of new technologies. Visual communication is one of the key components of modern media and social media.
Learn more in https://brainly.com/question/6753854
The subsequent result of the
system to the input is known
as
Select one:
A.Response
B.Command
C.Process Control
D.Process Controller
as
Under the right conditions, it is possible, due to surface tension,to have metal objects float on water. Consider placing a shortlength of a small diameter steel ( γ = 490 lb/ft3)rod on a surface of water. What is the maximum diameter that therod can have before it will sink? Assume that the surface tensionforces act vertically upward. Note: A standard paper cliphas a diameter of 0.036 in. Partially unfold a paper clip and seeif you can get it to float on water. Do the results of thisexperiment support your analysis?
Answer:
A) 0.0614 inches
b) The standard steel paper clip should float on water
Explanation:
The maximum diameter that the rod can have before it will sink
we can calculate this using this formula :
D = [tex](\frac{8\alpha }{\pi y } )^{\frac{1}{2} }[/tex] ----- 1
∝ = value of surface tension of water at 60⁰f = 5.03×10^−3 lb/ft
y = 490 Ib/ft^3
input the given values into equation 1 above
D = [tex](\frac{8*(5.3*10^{-3}) }{\pi *490 } )^{\frac{1}{2} }[/tex]
= 5.11 * 10^-3 ft convert to inches
= 5.11 *10^-3 ( 12 in/ 1 ft ) = 0.0614 inches
B) The diameter of a standard paper Cliphas = 0.036 inches
and the diameter of the rod = 0.0614. Hence the standard steel paper clip should float on water
A series motor runs at 1000 r.P.M. When the voltage is 415 V and the current is 30 A. The armature resistance is 0.5Ω and the series field resistance is 0.25 Ω. Determine the resistance to be connected in series to reduce the speed to 800 r.P.M with the same current.
Answer:
2.62 Ω
Explanation:
For a series motor, the field resistance is in series with the armature resistance. The back emf (e) is given by:
[tex]V=E_b+I_A(R_a+R_f)\\\\Where\ V\ is\ the\ terminal\ voltage, R_a=armature\ resistance,R_f=field \ resistance\\\\Given: V=415\ V,R_a=0.5 \Omega, R_f=0.25 \Omega,I_a=30A\\\\415=E_{b1}+30(0.5+0.25)\\\\415=E_{b1}+22.5\\\\E_{b1}=415-22.5=392.5V[/tex]
For a back emf of 392.5 V, the speed is 1000 rpm.
Speed is directly proportional to back emf. It is given as:
[tex]Nk\phi=E_b\\\\N_1k\phi_1= E_{b1}\\\\N_2k\phi_2= E_{b2}\\\\N_1=1000\ rpm, N_2=800\ rpm, E_{b1}=392.5\\\\\frac{E_{b1}}{E{b2}}= \frac{k\phi_1N_1}{k\phi_2N_2}\\\\\frac{E_{b1}}{E{b2}}= \frac{\phi_1N_1}{\phi_2N_2}\\But\ \phi\ is\ directly\ proportional\ to I_a\\\\\frac{E_{b1}}{E{b2}}= \frac{kI_{a1}N_1}{kI{a2}N_2}\\\\I_{a1}=I_{a2}\\\\\frac{E_{b1}}{E{b2}}= \frac{N_1}{N_2}\\\\E_{b2}=\frac{E_{b1}N_2}{N_1}=\frac{392.5*800}{1000}=314\ V[/tex]
Let the added resistance be R
[tex]V=E_{b2}+I_A(R_a+R_f+R)\\\\415=314+30(0.5+0.25+R)\\\\415=314+22.5+30R\\\\415=336.5+30R\\\\30R=78.5\\\\R=2.62\Omega[/tex]
1. Represent each of the following combinations of units in the correct SI form using the appropriate prefix: (a) μMN, (b) N/μm, (c) MN/ks2, and (d) kN/ms.
2. Represent each of the following quantities in the correct SI form using the appropriate prefix: (a) 0.000431 kg, (b) 35.3(103) N, (c) 0.00532 km.
3. Represent each of the following combinations of units in the correct SI form: (a) Mg/ms, (b) N/nm, and (c) mN/(kg⋅μs).
Answer:
Kindly check explanation
Explanation:
(a) μMN, (b) N/μm, (c) MN/ks2, and (d) kN/ms.
(a) μMN = (10^-6 * 10^6) = 10^(-6 + 6) = 10^0 = N
b) N/μm = N / 10^-6 m = 10^6 * N/m = MN/m
(c) MN/ks2 = 10^6N / (10^3 s)^2
10^6 N / 10^6s^2 = 10^6 * 10^-6 N /s^2 = N/s^2
D) kN/ms = 10^3N / 10^-3 s = 10^3 * 10^3 * N/s = 10^6N / s = MN/s
2)
a) 0.000431kg = 431 × 10^6 kg = 431 * 10^9g = 431Gg
b) 35.3 × 10^3 N
10^3 = kilo(K)
35.3 KN
C) 0.00532km = 5.32 * 10^3 km = 5.32 * 10^3 * 10^3 = 5.32 * 10^6 = 5.32Mm
3) Represent each of the following combinations of units in the correct SI form: (a) Mg/ms, (b) N/nm, and (c) mN/(kg⋅μs).
a) Mg/ms = 10^6g / 10^-3s = 10^6 * 10^3 g/s = 10^9 g/s = Gg/s
b) N/nm = N / 10^-9 m = 10^9 N/m = GN/m
c) mN/(kg⋅μs) = 10^6N / kg(10^-6s) = 10^12N/(kg.s)
= TN/(kg.s)