At what minimum angle will you get total internal reflection of light traveling in diamond and reflected from ethanol? °

Answers

Answer 1

Answer:

34°

Using the relation

θᶜ = sin^-1(n₂/n₁),

where n1= the refractive index of light is propagating from a medium

And n2 = refractive index of medium into which light is entering

So we know that

refractive index of diamond at 589nm = 2.41= n₁

refractive index of ethanol at 589nm and 20°C = 1.36= n₂

Thus. θᶜ = sin^-1(1.361/2.417) = 0.58radians = 34°

Explanation:


Related Questions

3. Which of the following accurately describes circuits?
O A. In a parallel circuit, the same amount of current flows through each part of the circuit
O B. In a series circuit, the amount of current passing through each part of the circuit may vary
O C. In a series circuit, the current can flow through only one path from start to finish
O D. In a parallel circuit, there's only one path for the current to travel.

Answers

Answer:

Option (c)

Explanation:

In a Series circuit, as the components are connected end-to-end ,the current can flow through only one path from start to finish.

(C.) is the only correct statement in the list of choices.

In a series circuit, the current can flow through only one path from start to finish.

If a disk rolls on a rough surface without slipping, the acceleration of the center of gravity (G) will _ and the friction force will b

Answers

Answer:

Will be equal to alpha x r; less than UsN

A thermos bottle works well because:

a. its glass walls are thin
b. silvering reduces convection
c. vacuum reduces heat radiation
d. silver coating is a poor heat conductor
e. none of the above

Answers

Answer:

A thermos bottle works well because:

A) Its glass walls are thin

Answer:

A thermos bottle works well because:

C

Vacuum reduces heat radiation

A patient prescribed a metered dose inhaler will find it
A. works for lower (not upper) respiratory diseases only.
B. should be filled with medication in aerosol form only.
C. is filled with medication used to administer a fixed amount of medication per inhalation through the mouth.
D. should be filled with medication in powder form only.

Answers

Answer:The correct answer should be C. is filled with medication used to administer a fixed amount of medication per inhalation through the mouth.

Explanation:

Answer:

c. is filled with medication used to administer a fixed amount of medication per inhalation through the mouth.

local unit of measurement of length : confined to a particular place cise Choose the best answer from the given alterna MKS system stands for ........ i. mass, kilogram and second ii. metre, kilogram and second iii. metre, kilometre and second iv. metre, kilogram and standard​

Answers

MKS stands for metre , kilogram and second

A projectile is shot from the edge of a cliff 80 m above ground level with an initial speed of 60 m/sec at an angle of 30° with the horizontal. Determine the time taken by the projectile to hit the ground below.

Answers

Answer:

8 seconds

Explanation:

Answer:

Explanation:

Going up

Time taken to reach maximum height= usin∅/g

=3 secs

Maximum height= H+[(usin∅)²/2g]

=80+[(60sin30)²/20]

=125 meters

Coming Down

Maximum height= ½gt²

125= ½(10)(t²)

t=5 secs

Three capacitors C1 = 10.7 µF, C2 = 23.0 µF, and C3 = 29.3 µF are connected in series. To avoid breakdown of the capacitors, the maximum potential difference to which any of them can be individually charged is 125 V. Determine the maximum energy stored in the series combination.

Answers

Answer:

E = 1336.71875 J

Explanation:

We are given;. Capacitance of Capacitor 1; C1 = 10.7 µF

Capacitor 2; C2 = 23.0 µF

Capacitor 3; C3 = 29.3 µF

Supply voltage;V = 125 V

Formula for capacitance in series is;

Capacitors in series circuit: C(eq) = 1/C(1) +1/C(2) +1/C(3) .......

Thus, equivalent capacitance is;

C(eq) = (1/10.7) + (1/23) + (1/29.3) = 0.1711 µF = 0.1711 × 10^(6) F

Now, the formula for maximum energy stored is;

E = ½ × C(eq) × V²

E = ½ × 0.1711 × 10^(-6) × 125²

E = 1336.71875 J

What type of energy conversion occurs when you place your feet near the fireplace and they become warm?
O Radiant to thermal
o Thermal to mechanical
O Mechanical to chemical
O Nuclear to thermal​

Answers

Answer:

It is the first one RADIENT TO THERMAL

Explanation:

The heat emitted from the campfires is an an example of radiant energy and thermal energy is refers to the energy contained within a system that is responsible for its tempreture with in this case is the campfires and heat energy being reflected upon your feet.

Answer:

A

Explanation:

The elastic portion of the downward-sloping straight-line demand curve lies:_______
a. at the intersection with the supply curve.
b. anywhere to the right of the current market price.
c. above the point of unit elasticity.
d. below the point where total revenue is maximized.

Answers

Answer:

c. above the point of unit elasticity.

Explanation:

The elastic portion of the downward-sloping straight-line demand curve lies above the point of unit elasticity. Supply and demand are fundamental concept in economics. The demand curve shows how much of a good people will want at a different prices. The demands curves illustrates the intuition why people purchase a good for a lower price. For the demand curve, the price is always shown on the vertical axis and the demand curve is shown on the horizontal axis. Thus , the quantity demanded increases as the price gets lower. However, the price elasticity of the demand curve varies along the demand curve. This is because there is a key distinction between the gradient and the elasticity. The gradient which is the slope of the line is always the same in the demand curve but elasticity of the demand changes in the percentage of the quantity demand. Therefore, elasticity will vary along the downward-sloping straight - line demand curve. So,  in a downward-sloping straight-line demand curve, the elastic portion is usually above the  point of unit elasticity

Suppose we want to calculate the moment of inertia of a 56.5 kg skater, relative to a vertical axis through their center of mass.

Required:
a. First calculate the moment of inertia (in kg-m^2) when the skater has their arms pulled inward by assuming they are cylinder of radius 0.11 m.
b. Now calculate the moment of inertia of the skater (in kg-m^2) with their arms extended by assuming that each arm is 5% of the mass of their body. Assume the body is a cylinder of the same size, and the arms are 0.875 m long rods extending straight out from their body being rotated at the ends.

Answers

Answer:

a. 0.342 kg-m² b. 2.0728 kg-m²

Explanation:

a. Since the skater is assumed to be a cylinder, the moment of inertia of a cylinder is I = 1/2MR² where M = mass of cylinder and r = radius of cylinder. Now, here, M = 56.5 kg and r = 0.11 m

I = 1/2MR²

= 1/2 × 56.5 kg × (0.11 m)²

= 0.342 kgm²

So the moment of inertia of the skater is

b. Let the moment of inertia of each arm be I'. So the moment of inertia of each arm relative to the axis through the center of mass is (since they are long rods)

I' = 1/12ml² + mh² where m = mass of arm = 0.05M, l = length of arm = 0.875 m and h = distance of center of mass of the arm from the center of mass of the cylindrical body = R/2 + l/2 = (R + l)/2 = (0.11 m + 0.875 m)/2 = 0.985 m/2 = 0.4925 m

I' = 1/12 × 0.05 × 56.5 kg × (0.875 m)² + 0.05 × 56.5 kg × (0.4925 m)²

= 0.1802 kg-m² + 0.6852 kg-m²

= 0.8654 kg-m²

The total moment of inertia from both arms is thus I'' = 2I' = 1.7308 kg-m².

So, the moment of inertia of the skater with the arms extended is thus I₀ = I + I'' = 0.342 kg-m² + 1.7308 kg-m² = 2.0728 kg-m²

a) The moment of inertia as the skater pulled his/her arm inward by assuming he/she is a cylinder is 0.3418kg-m².

b) If the body of the skater is assumed to be a cylinder of the same size, and the arms are rods extending straight out from his/her body being rotated at the ends, the moment of inertia is 1.7495kg-m².

Given the data in the question;

Mass of skater; [tex]M = 56.5kg[/tex]

a)

When the skater has his arms pulled inward by assuming they are cylinder of radius; [tex]R = 0.11 m[/tex]

Moment of inertia; [tex]I = \ ?[/tex]

From Parallel axis theorem; Moment of Inertia for a cylindrical body is expressed:

[tex]I = \frac{1}{2}MR^2[/tex]

Where M is the mass and R is the radius

We substitute our given values into the equation

[tex]I = \frac{1}{2}\ *\ 56.5kg\ *\ (0.11m)^2\\\\I = \frac{1}{2}\ *\ 56.5kg\ *\ 0.0121m^2\\\\I = 0.3418kg.m^2[/tex]

Therefore, the moment of inertia as the skater pulled his/her arm inward by assuming he/she is a cylinder is 0.3418kg-m²

b)

With the skater's arms extended by assuming that each arm is 5% of the mass of their body

Mass of each arm; [tex]M_a = \frac{5}{100} * M = \frac{5}{100} * 56.5kg = 2.825kg[/tex]

Remaining mass; [tex]M_b = M - 2M_a = 56.5kg - 2(2.825kg) = 50.85kg[/tex]

Assume the body is a cylinder of the same size and the arms are 0.875 m long rods extending straight out from their body being rotated at the ends.

Length of arm; [tex]L = 0.875 m[/tex]

From Parallel axis theorem; Moment of Inertia about vertical axis is expressed as:

[tex]I = \frac{1}{2}M_bR^2 + \frac{2}{3}M_aL^2[/tex]

We substitute in our values

[tex]I = \frac{1}{2}*50.85kg*(0.11m)^2 + \frac{2}{3}*2.825kg*(0.875m)^2\\\\I = [\frac{1}{2}*50.85kg * 0.0121m^2] + [\frac{2}{3}*2.825kg*0.765625m^2]\\\\I = 0.3076kg.m^2 + 1.4419kg.m^2\\\\I = 1.7495kg.m^2[/tex]

Therefore, if the body of the skater is assumed to be a cylinder of the same size, and the arms are rods extending straight out from his/her body being rotated at the ends, the moment of inertia is 1.7495kg-m².

Learn more: https://brainly.com/question/6897330

g As observed on earth, a certain type of bacteria is known to double in number every 24 hours. Two cultures of these bacteria are prepared, each consisting initially of one bacterium. One culture is left on earth and the other placed on a rocket that travels at a speed of 0.893c relative to the earth. At a time when the earthbound culture has grown to 256 bacteria, how many bacteria are in the culture on the rocket, according to an earth-based observer

Answers

Answer:

86.4 hrs

Explanation:

The amount of bacteria is initially 1

It doubles every 24 hrs.

After first 24 hrs, the amount = 2

After next 24 hrs = 4

After next 24 hrs = 8

After next 24 hrs = 16

After next 24 hrs = 32

After next 24 hrs = 64

After next 24 hrs = 128

After next 24 hrs = 256

Total time taken to reach 256 = 24 x 8 = 192 hrs

For the bacteria culture on the rocket that travels at a speed of 0.893c relative to the earth, this time is contracted by the relationship

t = t'(1 - ¥^2)^0.5

Where t is the contracted time =?

t' is the time on earth

¥ = v/c

Where v is the speed of the rocket

c is the speed of light

since v = 0.893c

¥ = 0.893

Substituting, we have

t = 192 x (1 - 0.893^2)^0.5

t = 192 x 0.2025^0.5

t = 192 x 0.45 = 86.4 hrs

A charged capacitor and an inductor are connected in series. At time t = 0, the current is zero, but the capacitor is charged. If T is the period of the resulting oscillations, the next time, after t = 0 that the energy stored in the magnetic field of the inductor is a maximum is

Answers

Answer:

t = T / 2 all energy is stored in the inductor

Explanation:

The circuit described is an oscillating circuit where the charge of the condensation stops the inductor and vice versa, in this system the angular velocity of the oscillation is

          w = √1/LC

          2π / T =√1 / LC

          T = 2π  √LC

The energy is constant and for the initial instant it is completely stored in the capacitor

         Uc = Q₀² / 2C

In the process, the capacitor is discharging and the energy is stored in the inductor until when the charge in the capacitors zero, all the energy is stored in the inductor

        U = L I² / 2

in the intermediate instant the energy is stored in the two elements.

Since the period of the system is T for time t = 0 all energy is stored in the capacitor and for t = T / 2 all energy is stored in the inductor

After t = 0 the maximum energy stored in the magnetic field of the inductor is equal to [tex]U'=\dfrac{L I^{2}}{2}[/tex] for the time period, half of period of oscillation  (t = T/2).

The given problem is based on the charging and discharging concepts of capacitor. An oscillating circuit is a circuit where the charge of the capacitor stops the inductor and vice versa, in this system the angular frequency of the oscillation is given as,

[tex]\omega =\dfrac{1}{\sqrt{LC}}\\\\\\\dfrac{2 \pi}{T} =\dfrac{1}{\sqrt{LC}}\\\\\\T = 2\pi \times \sqrt{LC}[/tex]

here, T is the period of oscillation.

 

Also, the energy stored in the capacitor is constant and for the initial instant it is completely stored in the capacitor. So, the energy stored is given as,

[tex]U =\dfrac{Q^{2}}{2C}[/tex]

here, C is the capacitance.

In the process, the capacitor is discharging and the energy is stored in the inductor until when the charge in the capacitors zero, all the energy is stored in the inductor. So, the expression for the energy stored in the inductor is,

[tex]U'=\dfrac{L I^{2}}{2}[/tex]

here, L is the inductance and I is the current.

Note :- The period of the system is T for time t = 0 all energy is stored in the capacitor and for t = T / 2 all energy is stored in the inductor.

Thus, we conclude that after t = 0 the maximum energy stored in the magnetic field of the inductor is equal to [tex]U'=\dfrac{L I^{2}}{2}[/tex] for the time period, half of period of oscillation  (t = T/2).

Learn more about the capacitance here:

https://brainly.com/question/12644355

"A light beam incident on a diffraction grating consists of waves with two different wavelengths. The separation of the two first order lines is great if"

Answers

Answer:

A light beam incident on a diffraction grating consists of waves with two different wavelengths. The separation of the two first order lines is great if

the dispersion is great

The speed of a horse is 134 meters per second how long does it takes to travel a distance of 19,311?

Answers

Answer:

just need some focus

Explanation:

tan 13. The speed of a horse is 134 meters per second how long does it take to travel a distance of 19,311m? M+ tud V 134 14. You are walking down the block and see your neighbor's pitbull 30 meters away, out of the fence, starring at you. Suddenly, he starts running towards you at 20m/s. How long will it be before you're the pitbull's lunch?  V 15. A pendulum has a frequency of 2 Hz what is it's period. T = 1/2 16. You have just finished a 1600 mile trip, and it took you 16 hours. What was your average speed V = Ad At 17. You are flying from New York, NY to SanFrancisco California, a distance of 2582 miles, it takes 6.33hrs to complete the flight what was your average speed? give answer in m/s. V = Ad = At 3 of 6

Charge of uniform density (0.30 nC/m2) is distributed over the xy plane, and charge of uniform density (−0.40 nC/m2) is distributed over the yz plane. What is the magnitude of the resulting electric field at any point not in either of the two charged planes?

Answers

Answer: E = 39.54 N/C

Explanation: Electric field can be determined using surface charge density:

[tex]E = \frac{\sigma}{2\epsilon_{0}}[/tex]

where:

σ is surface charge density

[tex]\epsilon_{0}[/tex] is permitivitty of free space ([tex]\epsilon_{0} = 8.85.10^{-12}[/tex][tex]C^{2}/N.m^{2}[/tex])

Calculating resulting electric field:

[tex]E=E_{1} - E_{2}[/tex]

[tex]E = \frac{\sigma_{1}-\sigma_{2}}{2\epsilon_{0}}[/tex]

[tex]E = \frac{[0.3-(-0.4)].10^{-9}}{2.8.85.10^{-12}}[/tex]

[tex]E=0.03954.10^{3}[/tex]

E = 39.54

The resulting Electric Field at any point is 39.54N/C.

The magnitude of the resulting electric field at any point should be  28.2 N/C.

Calculation of the magnitude:

Since the Charge of uniform density (0.30 nC/m2) should be allocated over the xy plane, and charge of uniform density (−0.40 nC/m2)should be allocated over the yz plane.

So,

E1

= σ1/2ε0

= 0.30e-9/(2*8.85e-12)

= 16.949 N/C

So, direction of E1 is +z

Now

E2 = σ2/2ε0

= 0.40e-9/(2*8.85e-12)

= 22.6 N/C

So,  direction of E2 is -x

Now

E = √(E1*E1+E2*E2)

= √(16.949*16.949+22.6*22.6)

= 28.2 N/C

Learn more about magnitude here: https://brainly.com/question/14576767

A child is trying to throw a ball over a fence. She gives the ball an initial speed of 8.0 m/s at an angle of 40° above the horizontal. The ball leaves her hand 1.0 m above the ground and the fence is 2.0 m high. The ball just clears the fence while still traveling upwards and experiences no significant air resistance. How far is the child from the fence?

Answers

Answer:

the child is 1.581 m far from the fence

Explanation:

The diagrammatic illustration that give a better view of what the question denote can be seen in the image attached below.

From the image attached below, let assume that the release point is the origin, then equation of the motion (x) is as follows:

[tex]x - x_o = u_xt[/tex]

[tex]\mathtt{x = u_xt \ \ \ since (x_o = 0)}[/tex]  ---- (1)

the equation of the motion y is :

[tex]\mathtt{y - y_o =u_yt - 0.5 gt^2}[/tex]

[tex]\mathtt{y = u_yt-4.9t^2 \ \ \ since (y_o =0)}[/tex]

[tex]\mathtt{ 1= (u \ sin 40^0)t -4.9 \ t^2 }[/tex]

[tex]\mathtt{1 = 8 sin 40^0 t - 4.9 t^2}[/tex]

[tex]\mathtt{1 = 5.14t - 4.9t^2}[/tex]

[tex]\mathtt{4.9t^2 - 5.14t +1 = 0}[/tex]

By using the quadratic formula, we have;

[tex]\mathtt{ \dfrac{ -b \pm \sqrt{b^2 - 4ac}}{2a}} }[/tex]

where;

a = 4.9,   b = -5.14     c = 1

[tex]= \mathtt{ \dfrac{ -(-5.14) \pm \sqrt{(-5.14)^2 - 4(4.9)(1)}}{2(4.9)}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{26.4196 -19.6}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{6.8196}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14+ \sqrt{6.8196}}{9.8} \ \ OR \ \ \dfrac{ 5.14- \sqrt{6.8196}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14+ 2.6114}{9.8} \ \ OR \ \ \dfrac{ 5.14- 2.6114}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 7.7514}{9.8} \ \ OR \ \ \dfrac{ 2.5286}{9.8}} }[/tex]

[tex]= \mathbf{ 0.791 \ \ OR \ \ 0.258} }[/tex]

In as much as the ball is traveling upward, then we consider t= 0.258sec.

From equation (1)

[tex]\mathtt{x = u_x(0.258)}[/tex]

[tex]\mathtt{x = ucos 40^0 (0.258)}[/tex]

[tex]\mathtt{x = 8 \ cos 40^0 (0.258)}[/tex]

[tex]\mathbf{x = 1.581 \ m}[/tex]

Thus, the child is 1.581 m far from the fence

The advantage of a hydraulic lever is A : it transforms a small force acting over a large distance into a large force acting over a small distance. B : it transforms a small force acting over a small distance into a large force acting over a large distance. C : it allows you to exert a larger force with less work. D : it transforms a large force acting over a large distance into a small force acting over a small distance. E : it transforms a large force acting over a small distance into a small force acting over a large distance.

Answers

Answer:

A) it transforms a small force acting over a large distance into a large force acting over a small distance.

Explanation:

The hydraulic lever works based on Pascal's law of transmission of pressure through a fluid. In the hydraulic lever, the pressure transmitted is the same.

Pressure transmitted P = F/A

where F is the force applied

and A is the area over which the force is applied.

This pressure can be manipulated on the input end as a small force applied over a small area, and then be transmitted to the output end as a large force over a large area.

F/A = f/a

where the left side of the equation is for the output, and the right side is for the input.

The volume of the displaced fluid will be the same on both ends of the hydraulic lever. Since we know that

volume V = (area A) x (distance d)

this means that the the piston on the input smaller area of the hydraulic lever will travel a greater distance, while the piston on the larger output area of the lever will travel a small distance.

From all these, we can see that the advantage of a hydraulic lever is that it transforms a small force acting over a large distance into a large force acting over a small distance.

550 J of heat is added to the gas in an isothermal process. As the gas expands, pushing against the piston, how much work does it do

Answers

Answer:

The work done by the system is 550 J

Explanation:

Given;

heat added to the system, Q = 550 J

Apply the first law of thermodynamics;

ΔU = Q - W

Where;

ΔU is change in internal energy

Q is the heat added to the system

W is the work done by the system

During an isothermal process, the temperature of the system is constant for the entire process. During this process, the change in the internal energy is zero.

0 = Q - W

W = Q

W = 550 J

Therefore, the work done by the system is 550 J

What is the angle between a wire carrying an 8.40 A current and the 1.20 T field it is in, if 50.0 cm of the wire experiences a magnetic force of 2.55 N? ° (b) What is the force (in N) on the wire if it is rotated to make an angle of 90° with the field? N

Answers

Answer:

A. 30.38°

B 5.04N

Explanation:

Using

F= ILBsin theta

2 .55N= 8.4Ax 0.5mx 1.2T x sintheta

Theta = 30.38°

B. If theta is 90°

Then

F= 8.4Ax 0.5mx 1.2x sin 90°

F= 5.04N

A thick wire with a radius of 4.0 mm carries a uniform electric current of 1.0 A, distributed uniformly over its cross-section. At what distance from the axis of the wire, and greater than the radius of the wire, is the magnetic field strength equal to that at a distance 2.0 mm from the axis. distance

Answers

Answer:

8 mm

Explanation:

From the information given:

The Ampere circuital law can be used to estimate the magnetic field strength at two points when the distance is less than the radius and when the distance is greater than the radius.

when the distance is less than the radius ; we have:

[tex]B_1 = \dfrac{ \mu_o \times I \times r}{2 \times \pi \times \ d^2}[/tex]

when the distance is greater than the radius; we have:

[tex]B_2 = \dfrac{\mu_o \ \times I}{2 \ \times \pi \times R}[/tex]

Equating both equations together ; we have :

[tex]\dfrac{ \mu_o \times I \times r}{2 \times \pi \times \ d^2} = \dfrac{\mu_o \ \times I}{2 \ \times \pi \times R}[/tex]

[tex]\dfrac{1}{R}= \dfrac{r}{d^2}[/tex]

[tex]R= \dfrac{d^2}{r}[/tex]

where; d = radius of the wire and r = distance;

[tex]R =\dfrac{4^2}{2}[/tex]

[tex]R =\dfrac{16}{2}[/tex]

R = 8 mm

Select the situation for which the torque is the smallest.

a. A 200 kg piece of silver is placed at the end of a 2.5 m tree branch.
b. A 20 kg piece of marble is placed at the end of a 25 m construction crane arm.
c. A 8 kg quartz rock is placed at the end of a 62.5 m thin titanium rod.
d. The torque is the same for two cases.
e. The torque is the same for all cases.

Answers

Answer:

e. The torque is the same for all cases.

Explanation:

The formula for torque is:

τ = Fr

where,

τ = Torque

F = Force = Weight (in this case) = mg

r = perpendicular distance between force an axis of rotation

Therefore,

τ = mgr

a)

Here,

m = 200 kg

r = 2.5 m

Therefore,

τ = (200 kg)(9.8 m/s²)(2.5 m)

τ = 4900 N.m

b)

Here,

m = 20 kg

r = 25 m

Therefore,

τ = (20 kg)(9.8 m/s²)(25 m)

τ = 4900 N.m

c)

Here,

m = 8 kg

r = 62.5 m

Therefore,

τ = (8 kg)(9.8 m/s²)(62.5 m)

τ = 4900 N.m

Hence, the correct answer will be:

e. The torque is the same for all cases.

The highest mountain on mars is olympus mons, rising 22000 meters above the martian surface. If we were to throw an object horizontaly off the mountain top, how long would it take to reach the surface? (Ignore atmospheric drag forces and use gMars=3.72m/s^2

a. 2.4 minutes
b. 0.79 minutes
c. 1.8 minutes
d. 3.0 minutes

Answers

Answer:

  t = 1.81 min ,     the correct answer is c

Explanation:

This is a missile throwing exercise

The object is thrown horizontally, so its vertical speed is zero (voy = 0), let's use the equation

             y = y₀ + [tex]v_{oy}[/tex] t - ½ g t²

the final height is y = 0 and the initial height is y₀ = 22000 m

            0 = y₀ + 0 - ½ g t²

             

            t = √y 2y₀ / g

let's calculate

           t = √(2  22000 / 3.72)

           t = 108.76 s

let's reduce to minutes

           t = 108.76 s (1 min / 60 s)

           t = 1.81 min

The correct answer is c

A horizontal board of negligible thickness and area 1.0 m2 hangs from a spring scale that reads 50 N when a 4.0 m/s wind moves above the board. The air below the board is stationary. What does the scale read when the wind stops? The density of air is 1.25 kg/m3 .

Answers


Scale reading for no wind
Explanation:
From the question we are told that
Area
Weight of board
Velocity
Density of air
Generally the equation for pressure difference by Bernoulli equation is mathematically given by


Generally force acting on the board by air is mathematically given by


Therefore
Scale reading for no wind W'


Scale reading for no wind W'=60Ng

If a bus travels 50 km in 10 hours, how fast was the
bus travelling?

Answers

Answer:

5 kilometers per hour

Explanation:

Speed = distance / time

Distance: 50km

Time: 10 hours

Speed = 50/10 = 5kph

Answer:

5kmph

Explanation:

if the bus traveled 50 km in 10 hours, we have to divide 50 by 10 to see how fast it traveled per hour.

50/10 = 5

therefore, the bus was traveling 5 km per hour

hope this helps :)

When a battery is connected to a lightbulb properly, current flows through the lightbulb and makes it glow. How much current flows through the battery compared with the lightbulb

Answers

Answer:

The same amount of current flows through the battery and light bulb

Explanation:

Because for a single loop, the current is the same at every point in the loop. Thus, the amount of current that flows through the lightbulb is the same as the amount that flows through the battery

Answer:

The same amount of current flows through the battery and light bulb

Explanation:

Activity
Spend time observing or thinking about events that involve matter and energy. Which events can you explain? Which
events can't you explain? Now answer the following questions.
Part A
Describe three events that you cannot explain.

Answers

Answer:Eating. Your muscles in your arms and mouth use energy to feed itself. Then your body digest the food which also takes energy.

Sleep. When your tired, you don’t have much energy. It is said that you use more energy while your sleeping. But how do you become energized if you were using even more energy than before?

Answer:

Different kinds of balls bounce to different heights when dropped on the same floor.

Sugar dissolves faster in hot milk than in cold milk.

Plants grow more slowly when they are not near a window.

Explanation:

what is liquid pressure? and tell me its si unit please ​

Answers

The SI unit of pressure is the pascal: 1Pa=1N/m2 1 Pa = 1 N/m 2 . Pressure due to the weight of a liquid of constant density is given by p=ρgh p = ρ g h , where p is the pressure, h is the depth of the liquid, ρ is the density of the liquid, and g is the acceleration due to gravity.

In order to waken a sleeping child, the volume on an alarm clock is doubled. Under this new scenario, how much more energy will be striking the child's ear drums each second?

Answers

Answer:4 times more energy will be striking the childbearing

Explanation:

Because Volume is directly proportional to amplitude of sound. Energy is proportional to amplitude squared. If you triple the amplitude, you multiply the energy by 4

If the terminals of a battery with zero internal resistance are connected across two identical resistors in series, the total power delivered by the battery is 8.00 W. If the same battery is connected across the same resistors in parallel, what is the total power delivered by the battery

Answers

Answer:

24W

Explanation:

The series connection has a resistance of 2R

The parallel connection has a resistance of R/2 .. the resistance has decreased by a factor 4

Assuming the battery still provides the same pd .. the current increases by a factor of 4 .. increasing the power output by a factor of 4 also (P = V x A)

Power output = 4 x 8W .. .. So P = 24 W

Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 2.2% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of the galaxy relative to the earth

Answers

Answer:

Vrel= 0.75c

Explanation:

See attached file

Other Questions
The circumference of a sphere was measured to be 82 cm with a possible error of 0.5 cm. A. Use differentials to estimate the maximum error in the calculated volume.What is the relative error? B. Use differentials to estimate the maximum error in the calculated volume.What is the relative error? Please help with this question! A plant does not grow when its apical meristem is cut. justify the statement Proportion problems8 chickens would lay 20 eggs in 3 days.If chickens always lay eggs at the same rate,a) how many days would it take to chickens to lay 100 eggs?= 10 daysb) how many chickens would be required if a farmer needed 30 eggs each day?i need help how to do question b. i know answer bu,.t i need explaining.:] element x has two isotopes: x-27 and x-29. x-27 has an atomic mass of 26.975 and a relative abundance of 82.33%, and x-29 has an atomic mass of 29.018 and a relative abundance of 17.67%. calculate the atomic mass od element x. show your work A line passes through the point ( 10,3 ) and has a slope of 1/2. write an equation in slope-intercept form for this line. what is a fixed income Read the examples of how someone might feel after moving to a new place. Match each example with the tile on theright that shows the kind of challenge the speaker is facing.Why is she calling me a bookworm?I wonder what that means.succeeding in schoolI used to wear sandals every day, butno one here does.adjusting to differences in appearanceSunday is a day for rest, notfor shoppingunderstanding values and beliefsParking meters are all over this city!learning about government and lawsWith weekly tests in my classes,I'm always studyingovercoming language barriers A gold, ornate box with the purpose of holding a person's body after death.The image above is a photograph of King Tuts _______________.a.casingc.portraitb.sarcophagusd.monument Write a three paragraph argument for or against the idea of using controlled fires to protect wild areas. a car averaged 72 kph .on a trip if the car travelled for 9 hours how far did it go for each of the following express the first quantity as a percentage of the second quantity 1 year ' 4 month According to the lecture, bauxite is very important to which of the following industries? A. jewelry B. shipbuilding C. electronics D. soda Q3 Who did babur deafet In the first Battle of panipat ? I believe you can help me Given the equation 3x+7 which order of operations completely solves for x QUESTION 4Which action is the best method for assessing fluid balance?O a. Ask the client what his daily fluid intake usually is?O b. As the client to describe his daily elimination patterns.O c. Compare the amount of a client's fluid intake with fluid output.d. Summarize the client's daily diet and analyse his fluid needs. What caused the substantial schedule delay of software development for the Jaguar project? (b) How did the software problem impact the project? (c) If you were the project manager, what would you have done differently to prevent the software problem from happening? The loudness, L , of a sound (measured in decibels, dB) is inversely proportional to the square of the distance, d , from the source of the sound. When a person 14 feet from a jetski, it is 70 decibels loud. How loud is the jetski when the person is 46 feet away? A proposed cost-saving device has an installed cost of $790,000. The device will be used in a five-year project but is classified as three-year MACRS property for tax purposes. The required initial net working capital investment is $77,000, the tax rate is 21 percent, and the project discount rate is 10 percent. The device has an estimated Year 5 salvage value of $118,000. What level of pretax cost savings do we require for this project to be profitable?